Wear protective gloves. Sharp areas on the parts may injure your hands.
A bolt without a torque specification is shown in the standard bolt chart.
Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS
1.INSTALL FRONT SEAT WIRE LH
Attach the 6 clamps to install the front seat wire LH.
Connect the 3 connectors.
2.INSTALL SEAT ADJUSTER COVER CAP
Install the 2 seat adjuster cover caps to the separate type front seat cushion spring assembly LH.
3.INSTALL FRONT OUTER SEAT CUSHION EDGE PROTECTOR LH
Install the front outer seat cushion edge protector LH in the direction indicated by the arrow in the illustration.
4.INSTALL FRONT INNER SEAT CUSHION EDGE PROTECTOR LH
Use the same procedure described for the front outer seat cushion edge protector LH.
5.INSTALL FRONT LOWER SEAT CUSHION SHIELD LH
Attach the clip to install the front lower seat cushion shield LH.
Attach the hook in the direction indicated by the arrow in the illustration.
Install the screw.
6.INSTALL FRONT LOWER SEAT CUSHION SHIELD RH
Use the same procedure described for the front lower seat cushion shield LH.
7.INSTALL FRONT SEAT INNER BELT ASSEMBLY LH
Install the front seat inner belt assembly LH with the nut.
Attach the 2 clamps.
| *1 | Wire Harness Clamp |
| *2 | Connector Clamp |
Attach the 2 wire harness clamps and connector clamp.
8.INSTALL SEAT POSITION AIRBAG SENSOR
9.INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY LH
10.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER
Set the separate type front seat cushion cover in place.
Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 21 new hog rings as shown in the illustration.
Be careful not to damage the separate type front seat cushion cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.
Install the hog rings at the cutouts if they are there.
| *1 | Hog Ring Pliers | - | - |
| *a | Cutout | - | - |
11.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD
Attach the 9 hooks to install the separate type front seat cushion cover with pad.
| *1 | Wire Harness Clamp |
| *2 | Connector Clamp |
Attach the 3 wire harness clamps and connector clamp to connect the seat cushion heater wire.
Connect the connector.
12.INSTALL FRONT NO. 2 SEAT WIRE LH
Attach the 2 clamps to install the front No. 2 seat wire LH.
Connect the 2 connectors.
13.INSTALL FRONT SEAT AIRBAG ASSEMBLY LH
14.INSTALL SEATBACK FELT
Install the seatback felt to the separate type front seatback spring assembly LH.
15.INSTALL SEPARATE TYPE FRONT SEATBACK PAD
Install the separate type front seatback pad to the separate type front seatback spring assembly LH.
16.INSTALL FRONT SEATBACK HEATER ASSEMBLY LH
17.INSTALL SEPARATE TYPE FRONT SEATBACK COVER
Set the separate type front seatback cover in place.
| *1 | Hog Ring Pliers |
| *a | Cutout |
Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with 8 new hog rings as shown in the illustration.
Be careful not to damage the separate type front seatback cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.
Install the hog rings at the cutouts if they are there.
Pass the separate type front seatback cover bracket through the separate type front seatback pad.
Install the 2 nuts.
Close the 2 fasteners.
Pull the straps to tighten them and confirm that there is a protrusion visible on each side.
| *1 | Hog Ring Pliers |
| *a | Cutout |
Using hog ring pliers, connect the straps of the separate type front seatback cover to the separate type front seatback frame sub-assembly LH with 3 new hog rings as shown in the illustration.
Be careful not to damage the separate type front seatback cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the straps of the separate type front seatback cover.
Install the hog rings at the cutouts if they are there.
| *1 | Hog Ring Pliers |
| *a | Cutout |
Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback frame sub-assembly LH with 5 new hog rings as shown in the illustration.
Be careful not to damage the separate type front seatback cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the straps of the separate type front seatback cover.
Install the hog rings at the cutouts if they are there.
18.INSTALL FRONT SEAT HEADREST SUPPORT
Attach the 4 claws to install the 2 front seat headrest supports.
19.INSTALL SEPARATE TYPE FRONT SEATBACK ASSEMBLY
Install the separate type front seatback assembly with the 4 bolts.
Attach the 2 hooks.
Connect the connector and attach the wire harness clamp.
| *1 | Fastener |
Attach the fastener to connect the wire harness of the front seat airbag assembly LH.
| *1 | Wire Harness Clamp |
| *2 | Connector Clamp |
Attach the 4 wire harness clamps and connector clamp.
Connect the connector.
Attach the wire harness clamp and connector clamp.
Connect the rubber band.
20.INSTALL FRONT INNER SEAT CUSHION SHIELD LH
|
First |
|
Second |
Attach the 3 guides and 2 claws as indicated by the arrows in the order shown in the illustration to install the front inner seat cushion shield LH.
21.INSTALL POWER SEAT SWITCH ASSEMBLY
22.INSTALL POSITION CONTROL ECU AND SWITCH ASSEMBLY
23.INSTALL RECLINING POWER SEAT SWITCH KNOB
Attach the 2 claws to install the reclining power seat switch knob.
24.INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB
Attach the 2 claws to install the slide and vertical power seat switch knob.
25.INSTALL FRONT SEAT CUSHION SHIELD LH
Connect the 3 connectors and attach the 3 clamps.
Attach the 3 claws to close the cover.
|
First |
|
Second |
Attach the 3 guides and claw as indicated by the arrows in the order shown in the illustration to install the front seat cushion shield LH.
Attach the clip.
26.INSTALL FRONT INNER NO. 1 SEAT CUSHION SHIELD LH
Attach the 2 claws, guide and clip in the direction indicated by the arrow shown in the illustration to install the front inner No. 1 seat cushion shield LH.
Attach the claw and install the screw.