Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR
RM30B0U _59 Vehicle Exterior _009875 DOOR / HATCH _0054766 FRONT DOOR A

DOOR / HATCH  FRONT DOOR  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.

·

A bolt without a torque specification is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS



PROCEDURE

Hide 1.INSTALL FRONT DOOR PANEL CUSHION

a.

Install 2 new front door panel cushions.


Hide 2.INSTALL FRONT DOOR LOWER OUTSIDE MOULDING SUB-ASSEMBLY LH

Hide 5.INSTALL FRONT DOOR WINDOW REAR FRAME MOULDING LH

Hide 6.INSTALL DOOR FRAME GARNISH LH

a.

Attach the clip to install a new door frame garnish LH.


Hide 7.INSTALL FRONT DOOR WEATHERSTRIP LH

a.

Attach the 18 clips to install the front door weatherstrip LH.


b.

Attach the 2 clips.


Hide 8.INSTALL FRONT DOOR CHECK ASSEMBLY LH

a.

Apply MP grease to the sliding area of the front door check assembly LH.


b.

When reusing a bolt labeled A:

i.

Clean the threads of the bolt with non-residue solvent.


ii.

Apply adhesive to the threads of the bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.




c.

Install the front door check assembly to the door panel with the 2 bolts labeled B.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


d.
B337360
1.292,1.844 1.76,1.531 false 2.281,1.792 2.271,1.365 false 1.74,0.344 2.302,0.344 false 2.219,1.802 2.531,1.958 0.313,0.156 10 *1 2.323,0.26 2.635,0.417 0.313,0.156 10 *2 1.125,1.781 1.438,1.938 0.313,0.156 10 *2
*1 Bolt A
*2 Bolt B


Install the front door check assembly to the body panel with the bolt labeled A.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


Hide 9.INSTALL FRONT DOOR LOCK OPEN ROD LH

a.

Install the front door lock open rod LH to the front door outside handle frame sub-assembly LH.


b.
B333940
2.646,0.365 2.896,0.271 false 3.01,0.521 3.344,0.719 0.333,0.198 10 (1) 2.427,0.094 2.76,0.292 0.333,0.198 10 (2) 2.927,0.167 3.156,0.354 0.229,0.188 10 *1
*1 Snap


Rotate the snap in the direction indicated by the arrow shown in the illustration to attach the snap to the front door lock open rod LH.


Hide 10.INSTALL FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH

a.

Apply MP grease to the sliding area of the front door outside handle frame sub-assembly LH.


b.
B341307
0.042,0.052 0.354,0.208 0.313,0.156 10 *A 0.063,2.25 0.375,2.406 0.313,0.156 10 *B
*A Inside
*B Outside


Using a T30 "TORX" socket wrench, attach the claw to install the front door outside handle frame sub-assembly LH with the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


c.

w/ Entry and Start System:

Attach the 3 clamps.


Hide 11.INSTALL FRONT DOOR FRONT OUTSIDE HANDLE PAD

a.

Attach the 3 claws to install the front door front outside handle pad.


Hide 12.INSTALL FRONT DOOR REAR OUTSIDE HANDLE PAD

a.

Attach the 2 claws to install the front door rear outside handle pad.


Hide 13.INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH

a.

Apply MP grease to the sliding area of the front door outside handle assembly LH.


b.
B337364

Install the front door outside handle assembly LH by moving it in the direction indicated by the arrow shown in the illustration.


c.

w/ Entry and Start System:

i.

Attach the claw of the connector to connect the connector.


ii.

Attach the 2 claws of the connector cover to connect the connector cover.



Hide 14.INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY LH

a.

Install the front door inside locking cable assembly LH.


b.

Attach the 3 claws to close the cover.


Hide 15.INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH

a.

Install the front door lock remote control cable assembly LH.


Hide 16.INSTALL FRONT DOOR WITH MOTOR LOCK ASSEMBLY LH

Hide 17.INSTALL DOOR LOCK CYLINDER LH

a.

Attach the 2 claws to install the door lock cylinder LH to the front door outside handle cover LH.


Hide 18.INSTALL FRONT DOOR OUTSIDE HANDLE COVER LH

a.

Using a T30 "TORX" socket wrench, install the front door outside handle cover LH together with the front door lock cylinder with the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


b.

Install the hole plug.


Hide 19.INSTALL FRONT DOOR BELT MOULDING ASSEMBLY LH

Hide 20.INSTALL FRONT DOOR NO. 2 STIFFENER CUSHION

HINT:

When installing the front door No. 2 stiffener cushion, heat the front door panel using a heat light.


Standard:
Item Temperature
Front Door Panel 40 to 60°C (104 to 140°F)


NOTICE:

Do not heat the front door panel excessively.


a.

Clean the front door panel surface.

i.

Using a heat light, heat the front door panel surface.


ii.

Remove the double-sided tape from the front door panel.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Install a new front door No. 2 stiffener cushion.

i.

Using a heat light, heat the front door panel.


ii.

Remove the peeling paper from the face of the front door No. 2 stiffener cushion.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



iii.

Install the front door No. 2 stiffener cushion with the 2 bolts.

HINT:

Press the front door No. 2 stiffener cushion firmly to install it.


Torque:
6.2 N*m (63 kgf*cm, 55 in.*lbf)



Hide 21.INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH

a.

Attach the guide to install the front door rear lower frame sub-assembly LH with the bolt.

Torque:
6.2 N*m (63 kgf*cm, 55 in.*lbf)


Hide 22.INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

Hide 23.INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY LH

a.

Apply MP grease to the sliding and rotating areas of the front door window regulator sub-assembly LH.


b.

Temporarily install the temporary bolt to the front door window regulator sub-assembly LH.


c.
B341324
2.094,1.125 1.396,0.313 true 2.344,1.823 2.552,2.052 0.208,0.229 10 (1) 2.635,0.792 2.833,1.01 0.198,0.219 10 (2) 2.177,0.927 2.385,1.177 0.208,0.25 10 (3) 2.698,1.615 2.917,1.833 0.219,0.219 10 (4) 1.792,1.094 1.99,1.344 0.198,0.25 10 (5) 1.521,0.958 1.729,1.208 0.208,0.25 10 (6) 1.24,0.229 1.458,0.448 0.219,0.219 10 *1
*1 Temporary Bolt


Install the front door window regulator sub-assembly LH with the 5 bolts, and then tighten the temporary bolt.

HINT:

Tighten the bolts in the order shown in the illustration.


Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

NOTICE:

Be careful not to drop the front door window regulator as it may become damaged.



d.

Connect the connector.


Hide 24.INSTALL FRONT DOOR GLASS RUN LH

a.

Install the front door glass run LH.


Hide 25.INSTALL FRONT DOOR GLASS SUB-ASSEMBLY LH

a.

Temporarily install the power window regulator master switch assembly with front door armrest base panel.


b.

Connect the cable to the negative (-) battery terminal.


c.

Operate the front door window regulator so that the front door glass can be installed.


d.

Disconnect the cable from the battery negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



e.

Remove the power window regulator master switch assembly with front door armrest base panel.


f.
B337363
1.906,0.281 2.229,0.51 0.323,0.229 10 (1) 0.552,0.625 1.115,0.844 0.563,0.219 10 (2)

Insert the front door glass sub-assembly LH into the front door panel along the front door glass run LH as indicated by the arrows in the order shown in the illustration.


g.

Install the front door glass sub-assembly LH with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 26.INSTALL FRONT DOOR SERVICE HOLE COVER LH

a.

Apply new butyl tape to the front door panel.


b.
B341312
0.438,0.354 0.292,0.396 false 2.573,0.531 2.656,0.573 false 0.125,0.354 0.354,0.531 0.229,0.177 10 false *a 2.688,0.531 2.896,0.76 0.208,0.229 10 false *a
*a Reference Point


Pass the front door inside locking cable assembly LH, front door lock remote control cable assembly LH and wire harness through a new front door service hole cover LH, and then attach the front door service hole cover LH using the reference points on the front door panel.

HINT:
·

Securely install the front door service hole cover to prevent wrinkles and air bubbles.

·

There should be no wrinkles or folds after installing the front door service hole cover.

·

After installing the front door service hole cover, check the seal quality.




c.

Connect the connector.


d.

Attach the 3 clamps.


e.

Install the bolt to the wire harness.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


Hide 27.INSTALL FRONT NO. 1 SPEAKER ASSEMBLY

Hide 29.INSTALL OUTER REAR VIEW MIRROR ASSEMBLY LH

Hide 30.INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP LH

a.
B337361

Install the front door inner glass weatherstrip LH to the front door trim board sub-assembly LH and fold down the 7 claws in the directions indicated by the arrows shown in the illustration.


Hide 31.INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY LH

a.

Attach the 2 claws and guide to install the front door inside handle sub-assembly LH.


Hide 32.INSTALL SEAT MEMORY SWITCH

Hide 33.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

a.

Connect the front door lock remote control cable assembly LH and front door inside locking cable assembly LH.


b.

Engage the front door lock remote control cable assembly LH and front door inside locking cable assembly LH to the 2 clamps.


c.

Attach the 9 clips to install the front door trim board sub-assembly LH.


d.

Install the 3 screws.


Hide 34.INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG LH

a.

Attach the 3 claws to install the front door inside handle bezel plug LH.


Hide 35.INSTALL FRONT DOOR ASSIST GRIP COVER LH

a.

Attach the guide, 2 clips and 4 claws to install the front door assist grip cover LH.


Hide 36.INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (for Driver Side)

Hide 37.INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)

a.

Connect the connector.


b.

Attach the 6 claws, 2 guides and 2 clips to install the power window regulator master switch assembly with front door armrest base panel.


Hide 38.INSTALL DOOR CONTROL SWITCH (for Front Passenger Side)

Hide 39.INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Front Passenger Side)

Hide 40.INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)

a.

Connect the connector.


b.

Attach the 6 claws, 2 guides and 2 clips to install the power window regulator switch assembly with front door armrest base panel.


Hide 41.INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH LH

a.

Attach the 2 claws, 2 clips and 2 guides to install the front door lower frame bracket garnish.


Hide 42.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 44.INITIALIZE POWER WINDOW CONTROL SYSTEM (w/ Jam Protection Function)

Hide 46.CHECK POWER DOOR LOCK CONTROL SYSTEM