Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)
RM30B0U _58 Vehicle Interior _009988 HEATING / AIR CONDITIONING _0054778 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  B1412/12  Ambient Temperature Sensor Circuit  


DESCRIPTION

The cooler (ambient temperature sensor) thermistor is installed in front of the condenser to detect the ambient temperature which is used to control the air conditioning system AUTO mode. This sensor is connected to the air conditioning amplifier assembly and detects fluctuations in the ambient temperature. This data is used for controlling the cabin temperature. The sensor sends a signal to the air conditioning amplifier assembly. The resistance of the cooler (ambient temperature sensor) thermistor changes in accordance with the ambient temperature. As the temperature decreases, the resistance increases. As the temperature increases, the resistance decreases.

The air conditioning amplifier assembly applies a voltage (5 V) to the cooler (ambient temperature sensor) thermistor and reads voltage changes due to changes in the resistance of the cooler (ambient temperature sensor) thermistor. The combination meter assembly sends the read signal to the air conditioning amplifier via CAN communication.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
B1412/12 Ambient Temperature Sensor Circuit Open or short in cooler (ambient temperature sensor) thermistor circuit
·

Cooler (ambient temperature sensor) thermistor

·

Harness or connector

·

Air conditioning amplifier assembly

·

Combination meter assembly


Memorized (4 seconds or more) -

HINT:
·

The air conditioning amplifier assembly stores the DTC of the respective malfunction if it has occurred for the period of time indicated in the brackets.

·

If the ambient temperature is approximately -52.9°C (-63.22°F) or less, DTC B1412/12 may be output even though the system is normal.



WIRING DIAGRAM

E269944
5.25,1.656 5.708,1.854 0.458,0.198 10 G81 5.25,1.823 6.833,2.177 1.583,0.354 10 Air Conditioning Amplifier Assembly 2.948,1.646 3.406,1.844 0.458,0.198 10 G16 2.948,1.823 4.208,2.177 1.26,0.354 10 Combination Meter Assembly 0.479,1.646 0.938,1.844 0.458,0.198 10 A26 0.469,1.813 2.26,2.167 1.792,0.354 10 Cooler (Ambient Temperature Sensor) Thermistor 0.635,2.406 2.458,2.615 1.823,0.208 10 : CAN Communication Line 3.083,1.313 3.698,1.51 0.615,0.198 10 TX1+ 1.271,1.417 1.615,1.615 0.344,0.198 10 SO+ 1.302,0.615 1.646,0.813 0.344,0.198 10 SO- 3.083,0.542 3.698,0.74 0.615,0.198 10 TX1- 2.813,0.406 3.021,0.594 0.208,0.188 10 34 1.635,0.396 1.844,0.583 0.208,0.188 10 1 2.802,1.208 3.01,1.396 0.208,0.188 10 35 1.646,1.198 1.854,1.385 0.208,0.188 10 2

CAUTION / NOTICE / HINT

NOTICE:

When the battery is disconnected or the air conditioning amplifier assembly is replaced, be sure to perform servo motor initialization.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)>INITIALIZATION


PROCEDURE

1.READ VALUE USING TECHSTREAM
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / Air Conditioner / Data List.


e.

Check the value(s) by referring to the table below.

Body Electrical > Air Conditioner > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Ambient Temp Sensor Cooler (ambient temperature sensor) thermistor Min.: -23.30°C (-9.94°F)
Max.: 65.95°C (150.71°F)
Actual ambient temperature displayed -
Body Electrical > Air Conditioner > Data List
Tester Display
Ambient Temp Sensor
50003 121 2
OK:

The display is as specified in the normal condition column.



Result:
Result Proceed to
OK (When troubleshooting according to Problem Symptoms Table) A
OK (When troubleshooting according to the DTC) B
NG C



A

B

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

C

2.INSPECT COOLER (AMBIENT TEMPERATURE SENSOR) THERMISTOR
2.INSPECT COOLER (AMBIENT TEMPERATURE SENSOR) THERMISTOR
a.

Remove the cooler (ambient temperature sensor) thermistor.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AMBIENT TEMPERATURE SENSOR>REMOVAL


b.

Inspect the cooler (ambient temperature sensor) thermistor.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AMBIENT TEMPERATURE SENSOR>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (COOLER [AMBIENT TEMPERATURE SENSOR] THERMISTOR - COMBINATION METER ASSEMBLY)

NG

REPLACE COOLER (AMBIENT TEMPERATURE SENSOR) THERMISTOR

3.CHECK HARNESS AND CONNECTOR (COOLER [AMBIENT TEMPERATURE SENSOR] THERMISTOR - COMBINATION METER ASSEMBLY)
a.

Disconnect the A26 cooler (ambient temperature sensor) thermistor connector.


b.

Disconnect the G16 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A26-1 (SO-) - G16-34 (TX1-) Always Below 1 Ω
A26-2 (SO+) - G16-35 (TX1+) Always Below 1 Ω
A26-1 (SO-) - Body ground Always 10 kΩ or higher
A26-2 (SO+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR