Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)
RM30B0U _58 Vehicle Interior _009988 HEATING / AIR CONDITIONING _0054778 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  B1442/42  Air Inlet Damper Control Servo Motor Circuit  


DESCRIPTION

The No. 1 blower damper servo sub-assembly (air inlet) sends pulse signals to inform the air conditioning amplifier assembly of the damper position. The air conditioning amplifier assembly activates the motor (normal, reverse) based on the signals to move the air inlet mode selection No. 1 blower damper servo sub-assembly (air inlet) to any position, which controls the intake air settings (FRESH, FRESH/RECIRCULATION, and RECIRCULATION).

The air conditioning amplifier assembly communicates with the servo through a communication/driver IC and wiring assembly called the air conditioning harness assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
B1442/42 Air Inlet Damper Control Servo Motor Circuit Air inlet damper position sensor value does not change even if air conditioning amplifier assembly operates No. 1 blower damper servo sub-assembly (air inlet)
·

No. 1 blower damper servo sub-assembly (air inlet)

·

Air conditioning harness assembly

·

Air conditioning amplifier assembly


Memorized (30 seconds or more) -

HINT:

The air conditioning amplifier assembly stores the DTC of the respective malfunction if it has occurred for the period of time indicated in the brackets.


WIRING DIAGRAM

E269946
5.573,3.115 6.031,3.313 0.458,0.198 10 false z7 3.719,3.302 4.969,3.76 1.25,0.458 10 false Air Conditioning Harness Assembly 5.563,3.302 6.781,3.76 1.219,0.458 10 false Air Conditioning Amplifier Assembly 0.198,3.104 1.99,3.781 1.792,0.677 10 false No. 1 Blower Damper Servo Sub-assembly (Air Inlet) 5.625,0.833 6.083,1.031 0.458,0.198 10 false BUS G 5.385,0.729 5.573,0.927 0.188,0.198 10 false 2 5.635,2.521 6.094,2.719 0.458,0.198 10 false B BUS 5.385,1.563 5.573,1.76 0.188,0.198 10 false 3 5.625,1.698 6.083,1.896 0.458,0.198 10 false BUS 5.375,2.396 5.563,2.594 0.188,0.198 10 false 4

CAUTION / NOTICE / HINT

NOTICE:

When the battery is disconnected or the air conditioning amplifier assembly is replaced, be sure to perform servo motor initialization.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)>INITIALIZATION


HINT:

Confirm that no mechanical problem is present because this diagnostic code can be output when either a damper link or the damper is mechanically locked.


PROCEDURE

1.READ VALUE USING TECHSTREAM
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Operate the R/F (Recirculation/Fresh) switch.


e.

Enter the following menus: Body Electrical / Air Conditioner / Data List.


f.

Check the value(s) by referring to the table below.

Body Electrical > Air Conditioner > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Air Inlet Damper Targ Pulse No. 1 blower damper servo sub-assembly (air inlet) target pulse Min.: 0
Max.: 255
RECIRCULATION: 19 (pulse)
FRESH: 7 (pulse)
Body Electrical > Air Conditioner > Data List
Tester Display
Air Inlet Damper Targ Pulse
50003 121 73
OK:

The display is as specified in the normal condition column.



Result:
Result Proceed to
OK (When troubleshooting according to the DTC) A
OK (When troubleshooting according to Problem Symptoms Table) B
NG C



A

2.CHECK NO. 1 BLOWER DAMPER SERVO SUB-ASSEMBLY (AIR INLET)

B

C

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

2.CHECK NO. 1 BLOWER DAMPER SERVO SUB-ASSEMBLY (AIR INLET)
a.

Replace the No. 1 blower damper servo sub-assembly (air inlet).

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT>DISASSEMBLY

HINT:

Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or known good one and check that the condition returns to normal.



b.

Check for DTC.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)>DTC CHECK / CLEAR

Body Electrical > Air Conditioner > Trouble Codes
50001 121

Result:
Proceed to
DTC B1442/42 is not output
DTC B1442/42 is output



DTC B1442/42 is not output

END (NO. 1 BLOWER DAMPER SERVO SUB-ASSEMBLY [AIR INLET] IS DEFECTIVE)

DTC B1442/42 is output

3.CHECK AIR CONDITIONING HARNESS ASSEMBLY
3.CHECK AIR CONDITIONING HARNESS ASSEMBLY
a.

Replace the air conditioning harness assembly.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT>REMOVAL

HINT:

Since the air conditioning harness assembly cannot be inspected while it is removed from the vehicle, replace the air conditioning harness assembly with a new or known good one and check that the condition returns to normal.



b.

Check for DTC.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)>DTC CHECK / CLEAR

Body Electrical > Air Conditioner > Trouble Codes
50001 121

Result:
Proceed to
DTC B1442/42 is not output
DTC B1442/42 is output



DTC B1442/42 is not output

END (AIR CONDITIONING HARNESS ASSEMBLY IS DEFECTIVE)

DTC B1442/42 is output

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY