Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)
RM30B0U _58 Vehicle Interior _009988 HEATING / AIR CONDITIONING _0054778 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  Air Conditioning Compressor Magnetic Clutch Circuit  


DESCRIPTION

When the air conditioning amplifier assembly is turned on, a magnet clutch assembly signal is sent from the MGC terminal of the air conditioning amplifier assembly. Then, the MG/CLT relay turns on to operate the magnet clutch assembly.

WIRING DIAGRAM

E271242
5.813,2.188 6.271,2.385 0.458,0.198 10 G81 5.813,2.375 7.031,2.792 1.219,0.417 10 Air Conditioning Amplifier Assembly 5.99,1.229 6.448,1.427 0.458,0.198 10 MGC 5.74,1.115 5.948,1.302 0.208,0.188 10 20 3.646,1.115 3.854,1.302 0.208,0.188 10 2 2.75,1.115 2.958,1.302 0.208,0.188 10 1 3.646,0.594 3.854,0.781 0.208,0.188 10 3 2.76,0.594 2.969,0.781 0.208,0.188 10 5 1.208,0.865 1.708,1.052 0.5,0.188 10 HTR-IG 2.802,1.563 3.917,1.771 1.115,0.208 10 MG/CLT Relay 1.354,1.979 2.771,2.219 1.417,0.24 10 from IG1 NO.1 Relay 4.01,2.875 4.469,3.073 0.458,0.198 10 3 3.625,3.073 4.083,3.271 0.458,0.198 10 MG+ 2.5,3.406 2.958,3.604 0.458,0.198 10 B68 2.5,3.573 4.167,3.781 1.667,0.208 10 Magnet Clutch Assembly

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.INSPECT MAGNET CLUTCH RELAY (MG/CLT)
a.
E273993
0.563,1.281 0.656,1.719 0.656,1.719 0.792,1.719 false 1.104,1.354 1.188,1.74 1.188,1.74 1.323,1.74 false 0.802,0.99 0.865,0.604 0.865,0.604 0.729,0.604 false 1.146,0.958 1.198,0.552 1.198,0.552 1.302,0.552 false 0.833,1.646 0.99,1.844 0.156,0.198 10 false 3 1.385,1.656 1.542,1.854 0.156,0.198 10 false 1 0.604,0.5 0.76,0.698 0.156,0.198 10 false 5 1.344,0.479 1.5,0.677 0.156,0.198 10 false 2

Remove the MG/CLT relay from the No. 2 engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage is not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage is applied to terminals 1 and 2 Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.INSPECT MAGNET CLUTCH ASSEMBLY

NG

REPLACE MAGNET CLUTCH RELAY (MG/CLT)

2.INSPECT MAGNET CLUTCH ASSEMBLY
a.
E198322
1.302,1.792 1.646,1.385 false 1.135,1.813 1.5,1.99 0.365,0.177 10 MG+

Remove the cooler compressor assembly.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>COMPRESSOR>REMOVAL


b.

Apply battery voltage to the magnet clutch assembly and check the operation of the magnet clutch assembly.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 3 (MG+)
Battery negative (-) → Body ground
Magnet clutch assembly operating sound can be heard, and magnet clutch hub and rotor lock.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (NO. 2 ENGINE ROOM RELAY BLOCK - BATTERY)

NG

3.CHECK HARNESS AND CONNECTOR (NO. 2 ENGINE ROOM RELAY BLOCK - BATTERY)
a.
E271243
0.042,0.042 0.354,0.24 0.313,0.198 10 *a 1.25,0.625 1.563,0.823 0.313,0.198 10 *1
*1 MG/CLT Relay
*a Component without relay installed
(No. 2 Engine Room Relay Block)


Remove the MG/CLT relay from the No. 2 engine room relay block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
MG/CLT relay terminal 1 - Body ground Ignition switch ON 11 to 14 V
MG/CLT relay terminal 5 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - BATTERY)
a.
E269948
1.469,0.313 1.896,0.573 0.427,0.26 0.49,0.969 0.635,0.969 0.635,0.969 0.771,1.26 true 1.542,0.365 2,0.563 0.458,0.198 10 G81 0.104,0.906 0.563,1.104 0.458,0.198 10 MGC
*a Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly)


Disconnect the air conditioning amplifier assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G81-20 (MGC) - Body ground Ignition switch off Below 1 V
G81-20 (MGC) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (NO. 2 ENGINE ROOM RELAY BLOCK - MAGNET CLUTCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (NO. 2 ENGINE ROOM RELAY BLOCK - MAGNET CLUTCH ASSEMBLY)
a.

Remove the MG/CLT relay from the No. 2 engine room relay block.


b.

Disconnect the B68 magnet clutch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
MG/CLT relay terminal 3 - B68-3 (MG+) Always Below 1 Ω
B68-3 (MG+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR