Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)
RM30B0U _56 Audio / Visual / Telematics _009403 AUDIO / VIDEO _0054848 AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)  Radio Broadcast cannot be Received or Poor Reception  


PROCEDURE

1.CHECK RADIO RECEIVER ASSEMBLY
a.

Check the radio automatic station search function by activating it.


Result:
Proceed to
Automatic station search function does not stop
Automatic station search function stops on a station



Automatic station search function does not stop

2.CHECK OPTIONAL COMPONENTS

Automatic station search function stops on a station

2.CHECK OPTIONAL COMPONENTS
a.

Check if any optional components that may decrease reception capacity, such as sunshade film or a telephone antenna, are installed.

NOTICE:

Do not remove optional components without the permission of the customer.



Result:
Proceed to
Optional components are not installed
Optional components are installed



Optional components are not installed

3.CHECK RADIO ANTENNA

Optional components are installed

REMOVE OPTIONAL COMPONENTS AND CHECK AGAIN (SEE NOTICE ABOVE)

3.CHECK RADIO ANTENNA
a.

Remove the roof antenna pole sub-assembly from the amplifier antenna assembly.


b.

Turn the ignition switch ACC with the radio receiver assembly connector connected.


c.

Turn the radio on and tune into AM mode.


d.

Place a screwdriver, thin wire, or other metal object on the amplifier antenna threaded installation portion for the roof antenna pole sub-assembly and check that noise can be heard from the speakers.


Result:
Proceed to
Noise does not occur
Noise occurs



Noise does not occur

4.CHECK RADIO RECEIVER ASSEMBLY

Noise occurs

REPLACE RADIO RECEIVER ASSEMBLY

4.CHECK RADIO RECEIVER ASSEMBLY
a.
E187251

Remove the antenna connector from the radio receiver assembly.


b.

Turn the ignition switch ACC with the radio receiver assembly connector connected.


c.

Turn the radio on and tune into AM mode.


d.

Place a screwdriver, thin wire or other metal object on the radio receiver assembly antenna jack and check that noise can be heard from the speakers.


Result:
Proceed to
Noise can be heard from the speakers
Noise cannot be heard from the speakers



Noise can be heard from the speakers

5.INSPECT RADIO RECEIVER ASSEMBLY

Noise cannot be heard from the speakers

REPLACE RADIO RECEIVER ASSEMBLY

5.INSPECT RADIO RECEIVER ASSEMBLY
a.

Disconnect the RA radio receiver assembly connector.


b.
E188455
1.552,1.104 1.146,1.479 true 0.844,1.51 1.24,1.677 0.396,0.167 10 ANT+

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
5 (ANT+) - Body ground Ignition switch ACC
Radio switch on and FM or AM selected
11 to 14 V



Result:
Proceed to
OK
NG



OK

6.CHECK ANTENNA CORD SUB-ASSEMBLY

NG

REPLACE RADIO RECEIVER ASSEMBLY

6.CHECK ANTENNA CORD SUB-ASSEMBLY
a.

Replace the antenna cord sub-assembly and check if radio broadcasts can be received normally.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER>REMOVAL


Result:
Proceed to
Radio broadcasts can be received normally
Radio broadcasts cannot be received normally



Radio broadcasts can be received normally

END (ANTENNA CORD SUB-ASSEMBLY IS DEFECTIVE)

Radio broadcasts cannot be received normally

7.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY
7.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY
a.

Replace the No. 2 antenna cord sub-assembly and check if radio broadcasts can be received normally.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD(for Roof Side)>REMOVAL


Result:
Proceed to
Radio broadcasts can be received normally
Radio broadcasts cannot be received normally



Radio broadcasts can be received normally

END (NO. 2 ANTENNA CORD SUB-ASSEMBLY IS DEFECTIVE)

Radio broadcasts cannot be received normally

8.CHECK NO. 3 ANTENNA CORD SUB-ASSEMBLY
8.CHECK NO. 3 ANTENNA CORD SUB-ASSEMBLY
a.

Replace the No. 3 antenna cord sub-assembly and check if radio broadcasts can be received normally.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD(for Roof Side)>REMOVAL


Result:
Proceed to
Radio broadcasts can be received normally
Radio broadcasts cannot be received normally



Radio broadcasts can be received normally

END (NO. 3 ANTENNA CORD SUB-ASSEMBLY IS DEFECTIVE)

Radio broadcasts cannot be received normally

9.CHECK ROOF ANTENNA POLE SUB-ASSEMBLY
9.CHECK ROOF ANTENNA POLE SUB-ASSEMBLY
a.

Check that the roof antenna pole sub-assembly is securely installed.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA POLE>REMOVAL


Result:
Proceed to
The roof antenna pole sub-assembly is installed properly
The roof antenna pole sub-assembly is not installed properly



The roof antenna pole sub-assembly is installed properly

10.CHECK ROOF ANTENNA POLE SUB-ASSEMBLY

The roof antenna pole sub-assembly is not installed properly

REINSTALL ROOF ANTENNA POLE SUB-ASSEMBLY

10.CHECK ROOF ANTENNA POLE SUB-ASSEMBLY
a.

Replace the roof antenna pole sub-assembly and check if radio broadcasts can be received normally.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA POLE>REMOVAL


Result:
Proceed to
Radio broadcasts can be received normally
Radio broadcasts cannot be received normally



Radio broadcasts can be received normally

END (ROOF ANTENNA POLE SUB-ASSEMBLY IS DEFECTIVE)

Radio broadcasts cannot be received normally

11.CHECK ANTENNA WITH HOLDER ASSEMBLY
11.CHECK ANTENNA WITH HOLDER ASSEMBLY
a.

Replace the antenna with holder assembly and check if radio broadcasts can be received normally.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA HOLDER>REMOVAL


Result:
Proceed to
Radio broadcasts can be received normally
Radio broadcasts cannot be received normally



Radio broadcasts can be received normally

END (ANTENNA WITH HOLDER ASSEMBLY IS DEFECTIVE)

Radio broadcasts cannot be received normally

REPLACE RADIO RECEIVER ASSEMBLY