Home › Steering › STEERING COLUMN › STEERING LOCK SYSTEM
RM30B0U _55 Steering _010850 STEERING COLUMN _0057945 STEERING LOCK SYSTEM J

STEERING COLUMN  STEERING LOCK SYSTEM  Unable to Lock Steering Wheel  


DESCRIPTION

The steering lock actuator activates the steering lock motor and moves the lock bar into the steering column to lock the steering.

When the steering lock is operating, the steering may not lock when the lock bar is not aligned with the lock hole of the steering column. In this case, the steering can be locked by turning the steering wheel a little in the same manner as is done for a vehicle with a mechanical key to change the position of the lock hole.

Related Data List and Active Test Items
Problem Symptom Data List Item Active Test Item
Unable to lock steering wheel
Smart Key

All items

(Click here)


Main Body

FL Door Courtesy SW


-

WIRING DIAGRAM

C280605
0.104,3.063 1.729,3.396 1.625,0.333 10 false Main Body ECU (Multiplex Network Body ECU) 1.979,3.052 2.281,3.208 0.302,0.156 10 false G84 1.979,3.219 3.521,3.563 1.542,0.344 10 false Certification ECU (Smart Key ECU Assembly) 2.49,1.708 2.885,1.865 0.396,0.156 10 false SLR+ 2.604,0.979 2.906,1.135 0.302,0.156 10 false LIN 2.906,0.813 3.302,0.969 0.396,0.156 10 false 17 2.917,1.573 3.313,1.729 0.396,0.156 10 false 29 5.146,0.802 5.271,0.969 0.125,0.167 10 false 5 5.146,1.594 5.271,1.76 0.125,0.167 10 false 3 5.344,0.979 5.646,1.135 0.302,0.156 10 false LIN 5.344,1.688 5.646,1.844 0.302,0.156 10 false IGE 5.167,2.385 5.292,2.552 0.125,0.167 10 false 1 5.333,2.49 5.854,2.698 0.521,0.208 10 false GND 5.208,3.021 5.51,3.177 0.302,0.156 10 false G5 5.219,3.208 6.99,3.552 1.771,0.344 10 false Steering Lock ECU (Steering Lock Actuator Assembly) 0.771,4.135 3.042,4.438 2.271,0.302 10 false : LIN Communication Line 0.771,4.458 3.042,4.76 2.271,0.302 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

When using the Techstream with the engine switch off to troubleshoot:

Connect the Techstream to the DLC3 and turn a courtesy light switch on and off at 1.5 second intervals until communication between the Techstream and vehicle begins.

·

Perform either of the following operations to lock/unlock the steering:

·

To unlock the steering, carry the key and turn the engine switch on (ACC) or on (IG) with the shift lever in P.

·

To lock the steering, turn the engine switch off with the shift lever in P, and then open a door.


·

Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart.

Click hereSteering>STEERING COLUMN>STEERING LOCK SYSTEM>DIAGNOSTIC TROUBLE CODE CHART

·

The steering lock system uses LIN communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

When replacing the steering lock ECU (steering lock actuator assembly) or certification ECU (smart key ECU assembly), registration must be performed.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Smart Key System)>REGISTRATION

·

After performing repairs, confirm that the problem does not occur.



PROCEDURE

1.CHECK DTC (ALL)
a.

Using the Techstream, confirm the output of DTCs for all systems.

OK:

No DTCs are output.


NOTICE:
·

When using the Techstream with the engine switch off to troubleshoot:

Connect the Techstream to the DLC3 and turn a courtesy light switch on and off at 1.5 second intervals until communication between the Techstream and vehicle begins.

·

Make sure that no DTCs are output. If any DTCs are output, proceed to Diagnostic Trouble Code Chart.




Result:
Proceed to
OK
NG



OK

2.READ VALUE USING TECHSTREAM (LOCK REQUEST RECEIVE)

NG

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS

2.READ VALUE USING TECHSTREAM (LOCK REQUEST RECEIVE)
a.

Use the Data List to check if the steering lock command is functioning properly.

Body Electrical > Smart Key > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Lock Request Receive Reception state of steering lock request signal by certification ECU (smart key ECU assembly)
HINT:
·

The reception state is maintained for 10 seconds.

·

When 10 seconds or more elapse after receiving the signal, the item changes to "NG".



OK or NG OK: Lock request signal received for 10 sec. of any of the doors being opened with shift lever in P and engine switch off.
NG: Except above
If OK is not displayed even though the steering lock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning.
Body Electrical > Smart Key > Data List
Tester Display
Lock Request Receive
50003 125 68
OK:

The certification ECU (smart key ECU assembly) receives a lock request signal within 10 seconds of turning the engine switch from on (IG) to off and opening a door with the shift lever in P, and OK is displayed on the Techstream screen.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (GROUND)

NG

6.READ VALUE USING TECHSTREAM (FL DOOR COURTESY SW)
3.CHECK HARNESS AND CONNECTOR (GROUND)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the G5 steering lock ECU connector.


c.
C157850
1.479,0.854 1.896,1.115 0.417,0.26 1.188,2.448 0.646,1.938 false 1.573,0.896 2.031,1.094 0.458,0.198 10 G5 0.135,0.104 0.448,0.302 0.313,0.198 10 *a 0.469,1.771 0.927,1.969 0.458,0.198 10 GND
*a Front view of wire harness connector
(to Steering Lock ECU (Steering Lock Actuator Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G5-1 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.INSPECT STEERING LOCK ECU (MOTOR ACTIVATION COMMAND SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT STEERING LOCK ECU (MOTOR ACTIVATION COMMAND SIGNAL)
a.

Reconnect the G5 steering lock ECU connector.


b.

Turn the engine switch off, make sure that the steering is unlocked and move the shift lever to P.


c.
C241547
0.323,2.917 1.646,3.031 1.323,0.115 2.333,2.969 2.76,3.073 0.427,0.104 1.594,4.073 2.417,4.188 0.823,0.115 0.198,0.833 0.615,1.104 0.417,0.271 0.844,1.833 1.854,1.104 false 2.833,1.833 2.292,1.104 false 2.542,3.198 2.542,3.073 false 1.99,4.063 1.99,3.938 false 0.979,3.167 0.979,3.042 false 0.906,3.167 1.219,3.323 0.313,0.156 10 *b 1.906,3.76 2.219,3.917 0.313,0.156 10 *c 2.469,3.208 2.781,3.365 0.313,0.156 10 *b 0.146,0.115 0.458,0.271 0.313,0.156 10 *a 0.708,1.865 1.167,2.063 0.458,0.198 10 IGE 2.74,1.854 3.198,2.052 0.458,0.198 10 GND 2.979,4.063 3.365,4.24 0.385,0.177 10 GND 0.302,0.885 0.667,1.083 0.365,0.198 10 G5
*a Component with harness connected
(Steering Lock ECU (Steering Lock Actuator Assembly))
*b Steering lock motor not operating
*c Steering lock motor operating


Check the signal waveform according to the condition(s) in the table below.

Standard Frequency
Item Content
Tester Connection G5-3 (IGE) - G5-1 (GND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Vehicle Condition Steering lock motor not operating → Steering lock motor operating → Steering lock motor not operating

HINT:
·

When taking measurements when the lock motor is stopped, it is not necessary to perform any operations.

·

In order to take measurements when the lock motor is operating, perform either of the following operations:

·

To unlock the steering, carry the key and turn the engine switch on (ACC) or on (IG) with the shift lever in P.

·

To lock the steering, turn the engine switch off with the shift lever in P, and then open a door.





Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


b.

Disconnect the G5 steering lock ECU connector.


c.

Disconnect the G84 certification ECU (smart key ECU assembly) connector.


d.

Check for deformation and corrosion of the connector case and terminals.

OK:

There is no deformation or corrosion of the connector case or terminals.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G5-3 (IGE) - G84-29 (SLR+) Always Below 1 Ω
G5-3 (IGE) - Body ground 10 kΩ or higher
G84-29 (SLR+) - Body ground



Result:
Proceed to
OK
NG



OK

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.READ VALUE USING TECHSTREAM (FL DOOR COURTESY SW)
a.

Using the Techstream, check the following main body ECU Data List item by opening and closing the driver door to confirm the state of the front door courtesy light switch assembly.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FL Door Courtesy SW Front door courtesy light switch assembly LH ON or OFF OFF: Front door LH closed
ON: Front door LH open
If this item does not change according to the actual state of the driver door, there is a malfunction in the door courtesy light switch or related part.
Body Electrical > Main Body > Data List
Tester Display
FL Door Courtesy SW
50003 123 199
OK:

The Data List item changes in accordance with the opening and closing of the driver door.



Result:
Proceed to
OK
NG



OK

7.READ VALUE USING TECHSTREAM (L CODE CHECK)

NG

GO TO LIGHTING SYSTEM (DOOR COURTESY SWITCH CIRCUIT)

7.READ VALUE USING TECHSTREAM (L CODE CHECK)
a.

Use the Data List to check if L code certification is functioning properly.

Body Electrical > Smart Key > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
L Code Check Verification result between certification ECU (smart key ECU assembly) and steering lock ECU (steering lock actuator assembly) OK or NG OK: Verification result normal
NG: Verification result abnormal
When NG is displayed:
·

The ID code for the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator assembly) is not registered or the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator assembly) is malfunctioning.

·

The steering cannot be locked.

·

The steering cannot be unlocked (the engine cannot be started).


Body Electrical > Smart Key > Data List
Tester Display
L Code Check
50003 125 66
OK:

OK is displayed on the Techstream.


HINT:

Reasons for verification failure:

·

The steering lock ECU or certification ECU (smart key ECU assembly) is malfunctioning.

·

There is a problem with the communication between ECUs.

·

An ECU is replaced, but is not registered.

·

An ECU is replaced with an ECU which has a code already stored in it.




Result:
Proceed to
OK
NG



OK

8.REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)

NG

9.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
8.REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)
a.

Replace the steering lock ECU (steering lock actuator assembly) with a new one.

Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>DISASSEMBLY



c.

Turn the engine switch on (IG).


d.

Turn the steering wheel and check the steering condition.

OK:

Steering is unlocked.



Result:
Proceed to
OK
NG



OK

END

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

9.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>CERTIFICATION ECU>REMOVAL



c.

Use the Data List to check if L code certification is functioning properly again.

Body Electrical > Smart Key > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
L Code Check Verification result between certification ECU (smart key ECU assembly) and steering lock ECU (steering lock actuator assembly) OK or NG OK: Verification result normal
NG: Verification result abnormal
When NG is displayed:
·

The ID code for the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator assembly) is not registered or the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator assembly) is malfunctioning.

·

The steering cannot be locked.

·

The steering cannot be unlocked (the engine cannot be started).


Body Electrical > Smart Key > Data List
Tester Display
L Code Check
50003 125 66
OK:

OK is displayed on the Techstream.



Result:
Proceed to
OK
NG



OK

END

NG

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)