Home › Steering › STEERING COLUMN › STEERING LOCK SYSTEM
RM30B0U _55 Steering _010850 STEERING COLUMN _0057945 STEERING LOCK SYSTEM J

STEERING COLUMN  STEERING LOCK SYSTEM  Unable to Unlock Steering Wheel (Engine cannot Start)  


DESCRIPTION

The steering lock actuator assembly activates the steering lock motor and moves the lock bar into the steering column to lock the steering.

The steering may not unlock when the lock bar gets stuck in the lock hole of the steering column. In this case, if an engine start operation is performed while shaking the steering wheel in the same manner as is done for a vehicle with a mechanical key, the lock bar will be unlocked. If the certification ECU (smart key ECU assembly) or ECM is replaced, the system needs to be initialized. Otherwise, the steering cannot be unlocked and the engine cannot be started.

Related Data List and Active Test Items
Problem Symptom Data List Item Active Test Item
Unable to unlock steering wheel (Engine cannot start)
Smart Key

All items

(Click here)


-

WIRING DIAGRAM

C280606
2.302,0.927 3.167,1.115 0.865,0.188 10 false from Battery 3.844,1.083 4.708,1.271 0.865,0.188 10 false STRG LOCK 5.052,0.833 5.146,1.021 0.094,0.188 10 false 7 5.25,0.927 5.344,1.115 0.094,0.188 10 false B 5.042,1.51 5.135,1.698 0.094,0.188 10 false 5 5.052,2.125 5.146,2.313 0.094,0.188 10 false 3 5.052,5.031 5.146,5.219 0.094,0.188 10 false 1 5.229,1.667 5.5,1.865 0.271,0.198 10 false LIN 5.219,2.229 5.75,2.427 0.531,0.198 10 false IGE 5.24,5.198 5.854,5.396 0.615,0.198 10 false GND 5.063,5.802 5.406,5.99 0.344,0.188 10 false G5 5.073,5.958 6.844,6.333 1.771,0.375 10 false Steering Lock ECU (Steering Lock Actuator Assembly) 2.823,1.448 3.094,1.646 0.271,0.198 10 false 17 2.854,2.031 3.125,2.229 0.271,0.198 10 false 29 2.844,2.583 3.115,2.781 0.271,0.198 10 false 25 2.802,1.677 3.208,1.885 0.406,0.208 10 false G84 2.802,2.229 3.323,2.448 0.521,0.219 10 false G84 2.802,2.792 3.292,3 0.49,0.208 10 false G84 2.458,1.677 2.729,1.875 0.271,0.198 10 false LIN 2.344,2.219 2.729,2.448 0.385,0.229 10 false SLR+ 2.583,2.781 2.74,2.99 0.156,0.208 10 false P 1.604,2.958 1.875,3.156 0.271,0.198 10 false G82 1.677,2.729 1.948,2.927 0.271,0.198 10 false 11 0.031,3.521 1.677,3.885 1.646,0.365 10 false Main Body ECU (Multiplex Network Body ECU) 1.896,3.458 3.406,3.802 1.51,0.344 10 false Certification ECU (Smart Key ECU Assembly) 2.792,4.729 3.063,4.927 0.271,0.198 10 false 2 2.813,5.281 3.083,5.479 0.271,0.198 10 false 7 2.521,4.833 2.792,5.031 0.271,0.198 10 false P2 2.563,5.375 2.833,5.573 0.271,0.198 10 false E 1.677,5.823 2.052,6.021 0.375,0.198 10 false G35 1.688,6.01 3.583,6.354 1.896,0.344 10 false Shift Lock Control ECU (Lower Shift Lever Assembly) 0.813,7.042 2.542,7.229 1.729,0.188 10 false : LIN Communication Line 0.813,7.354 2.542,7.542 1.729,0.188 10 false : CAN Communication Line 1.969,2.979 2.125,3.188 0.156,0.208 10 false E

CAUTION / NOTICE / HINT

NOTICE:
·

When using the Techstream with the engine switch off to troubleshoot:

Connect the Techstream to the DLC3 and turn a courtesy light switch on and off at 1.5 second intervals until communication between the Techstream and vehicle begins.

·

Perform either of the following operations to lock/unlock the steering:

·

To unlock the steering, carry the key and turn the engine switch on (ACC) or on (IG) with the shift lever in P.

·

To lock the steering, turn the engine switch off with the shift lever in P, and then open a door.


·

The steering lock system uses LIN communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, confirm that the problem does not occur.

·

Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart.

Click hereSteering>STEERING COLUMN>STEERING LOCK SYSTEM>DIAGNOSTIC TROUBLE CODE CHART

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

When replacing the steering lock ECU (steering lock actuator assembly) or certification ECU (smart key ECU assembly), registration must be performed.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Smart Key System)>REGISTRATION

·

If the steering lock ECU (steering lock actuator assembly) is replaced, be sure to confirm that the steering is unlocked by turning the steering wheel to the left and right before starting the engine. If the steering is locked for any reason, open and close a door with the engine switch off, and then unlock the steering by pressing the engine switch. This prevents the engine from starting while the steering is locked.

·

When starting the engine, make sure that the shift lever is in P and that the shift lever is not tilted.



PROCEDURE

1.CHECK DTC (ALL)
a.

Using the Techstream, confirm the output of DTCs for all systems.

OK:

No DTCs are output.


NOTICE:
·

When using the Techstream with the engine switch off to troubleshoot:

Connect the Techstream to the DLC3 and turn a courtesy light switch on and off at 1.5 second intervals until communication between the Techstream and vehicle begins.

·

Make sure that no DTCs are output. If any DTCs are output, proceed to Diagnostic Trouble Code Chart.




Result:
Proceed to
OK
NG



OK

2.CHECK ENGINE SWITCH (SWITCH CONDITION)

NG

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS

2.CHECK ENGINE SWITCH (SWITCH CONDITION)
a.

Check the power source mode change.

i.

When the key is inside the vehicle and the shift lever is in P, check that pressing the engine switch with the brake pedal released causes the power source mode to change as follows:

OK:

Off → on (ACC) → on (IG) → off




Result:
Proceed to
OK
NG



OK

3.READ VALUE USING TECHSTREAM (UNLOCK REQUEST RECEIVE)

NG

GO TO SMART KEY SYSTEM (for Start Function) (PROBLEM SYMPTOMS TABLE)

3.READ VALUE USING TECHSTREAM (UNLOCK REQUEST RECEIVE)
a.

Use the Data List to check if the steering lock command is functioning properly.

Body Electrical > Smart Key > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Unlock Request Receive Reception state of steering unlock request signal by certification ECU (smart key ECU assembly)
HINT:
·

The reception state is maintained for 10 seconds.

·

When 10 seconds or more elapse after receiving the signal, the item changes to "NG".



OK or NG OK: Within 10 sec. of turning the engine switch on (IG) or on (ACC), or of an engine start operation being performed
NG: Engine switch on (IG) or on (ACC), or engine start operation not performed
·

The engine cannot be started when an unlock request signal cannot be received.

·

If OK is not displayed even though the steering unlock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning.


Body Electrical > Smart Key > Data List
Tester Display
Unlock Request Receive
50003 125 67
OK:

The certification ECU (smart key ECU assembly) receives a lock request signal within 10 seconds of turning the engine switch from on (IG) to off and opening a door with the shift lever in P, and OK is displayed on the Techstream screen.



Result:
Proceed to
OK
NG



OK

4.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

7.READ VALUE USING TECHSTREAM (L CODE CHECK)
4.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Measure the voltage according to the value(s) in the table below.

B264896
2.146,0.938 2.51,1.125 0.365,0.188 4.771,0.938 5.135,1.125 0.365,0.188 2.719,1.885 2.896,2.323 true 4.823,1.906 4.469,2.344 true 0.198,0.125 0.385,0.281 0.188,0.156 10 *a 2.885,2.396 3.167,2.552 0.281,0.156 10 E 2.208,0.958 2.583,1.115 0.375,0.156 10 G82 4.823,0.948 5.24,1.104 0.417,0.156 10 G84 4.365,2.396 4.646,2.552 0.281,0.156 10 P
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -


Standard Voltage:
Tester Connection Condition Specified Condition
G84-25 (P) - G82-11 (E) Shift lever in P 9 V or higher
Shift lever not in P 1.5 V or less



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

NG

9.CHECK HARNESS AND CONNECTOR (SHIFT LOCK CONTROL ECU (LOWER SHIFT LEVER ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
5.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
a.
C157850
1.542,0.813 1.948,1.063 0.406,0.25 1.188,2.427 0.635,2.021 false 2.24,2.5 2.594,2.021 false 1.625,0.854 2.083,1.052 0.458,0.198 10 G5 0.125,0.115 0.438,0.313 0.313,0.198 10 *a 2.625,1.833 2.781,2.031 0.156,0.198 10 B 0.458,1.792 0.917,1.99 0.458,0.198 10 GND
*a Front view of wire harness connector
(to Steering Lock ECU (Steering Lock Actuator Assembly))


Disconnect the G5 steering lock ECU connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G5-1 (GND) - Body ground Always Below 1 Ω


NOTICE:

If the result is not as specified, check for looseness in the connection which leads to ground.


Standard Voltage:
Tester Connection Condition Specified Condition
G5-7 (B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.INSPECT STEERING LOCK ECU (MOTOR ACTIVATION COMMAND SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT STEERING LOCK ECU (MOTOR ACTIVATION COMMAND SIGNAL)
a.

Reconnect the G5 steering lock ECU connector.


b.
C241547
0.323,2.917 1.646,3.031 1.323,0.115 2.333,2.969 2.76,3.073 0.427,0.104 1.594,4.073 2.417,4.188 0.823,0.115 0.198,0.833 0.615,1.104 0.417,0.271 0.844,1.833 1.854,1.104 false 2.833,1.833 2.292,1.104 false 2.542,3.198 2.542,3.073 false 1.99,4.063 1.99,3.938 false 0.979,3.167 0.979,3.042 false 0.906,3.167 1.219,3.323 0.313,0.156 10 *b 1.906,3.76 2.219,3.917 0.313,0.156 10 *c 2.469,3.208 2.781,3.365 0.313,0.156 10 *b 0.146,0.115 0.458,0.271 0.313,0.156 10 *a 0.708,1.865 1.167,2.063 0.458,0.198 10 IGE 2.74,1.854 3.198,2.052 0.458,0.198 10 GND 2.979,4.063 3.365,4.24 0.385,0.177 10 GND 0.302,0.885 0.667,1.083 0.365,0.198 10 G5
*a Component with harness connected
(Steering Lock ECU (Steering Lock Actuator Assembly))
*b Steering lock motor not operating
*c Steering lock motor operating


Check the signal waveform according to the condition(s) in the table below.

Standard Frequency
Item Content
Tester Connection G5-3 (IGE) - G5-1 (GND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Vehicle Condition Steering lock motor not operating → Steering lock motor operating → Steering lock motor not operating

HINT:
·

When taking measurements when the lock motor is stopped, it is not necessary to perform any operations.

·

In order to take measurements when the lock motor is operating, perform either of the following operations:

·

To unlock the steering, carry the key and turn the engine switch on (ACC) or on (IG) with the shift lever in P.

·

To lock the steering, turn the engine switch off with the shift lever in P, and then open a door.





Result:
Proceed to
OK
NG



OK

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.READ VALUE USING TECHSTREAM (L CODE CHECK)
a.

Use the Data List to check if L code certification is functioning properly.

Body Electrical > Smart Key > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
L Code Check Verification result between certification ECU (smart key ECU assembly) and steering lock ECU (steering lock actuator assembly) OK or NG OK: Verification result normal
NG: Verification result abnormal
When NG is displayed:
·

The ID code for the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator assembly) is not registered or the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator assembly) is malfunctioning.

·

The steering cannot be locked.

·

The steering cannot be unlocked (the engine cannot be started).


Body Electrical > Smart Key > Data List
Tester Display
L Code Check
50003 125 66
OK:

OK is displayed on the Techstream.


HINT:

Reasons for verification failure:

·

The steering lock ECU (steering lock actuator assembly) or certification ECU (smart key ECU assembly) is malfunctioning.

·

There is a problem with the communication between ECUs.

·

An ECU is replaced, but is not registered.

·

An ECU is replaced with an ECU which has a code already stored in it.




Result:
Proceed to
OK
NG



OK

8.REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)

NG

11.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
8.REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)
a.

Replace the steering lock ECU (steering lock actuator assembly) with a new one.

Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>DISASSEMBLY



c.

Turn the engine switch on (IG).


d.

Turn the steering wheel and check the steering condition.

OK:

Steering is unlocked.



Result:
Proceed to
OK
NG



OK

END

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

9.CHECK HARNESS AND CONNECTOR (SHIFT LOCK CONTROL ECU (LOWER SHIFT LEVER ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the G35 lower shift lever assembly connector.


b.

Disconnect the G84 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G35-2 (P2) - G84-25 (P) Always Below 1 Ω
G35-2 (P2) - Body ground 10 kΩ or higher
G84-25 (P) - Body ground



Result:
Proceed to
OK
NG



OK

10.INSPECT SHIFT LOCK CONTROL ECU (LOWER SHIFT LEVER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT SHIFT LOCK CONTROL ECU (LOWER SHIFT LEVER ASSEMBLY)
a.

Reconnect the G35 lower shift lever assembly connector.


b.
C197449
0.219,0.896 0.563,1.125 0.344,0.229 1.969,1.052 2.76,1.24 true 0.063,0.052 0.24,0.219 0.177,0.167 10 *a 2.802,1.198 3.052,1.354 0.25,0.156 10 P2 0.26,0.927 0.563,1.104 0.302,0.177 10 G35
*a Component with harness connected
(Shift Lock Control ECU (Lower Shift Lever Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G35-2 (P2) - Body ground Shift lever in P 9 V or higher
Shift lever not in P 1.5 V or less


Result:
Proceed to
OK
NG (for U760E)
NG (for U760F)




OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG (for U760E)

NG (for U760F)

11.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>CERTIFICATION ECU>REMOVAL



c.

Use the Data List to check if L code certification is functioning properly again.

Body Electrical > Smart Key > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
L Code Check Verification result between certification ECU (smart key ECU assembly) and steering lock ECU (steering lock actuator assembly) OK or NG OK: Verification result normal
NG: Verification result abnormal
When NG is displayed:
·

The ID code for the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator assembly) is not registered or the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator assembly) is malfunctioning.

·

The steering cannot be locked.

·

The steering cannot be unlocked (the engine cannot be started).


Body Electrical > Smart Key > Data List
Tester Display
L Code Check
50003 125 66
OK:

OK is displayed on the Techstream.



Result:
Proceed to
OK
NG



OK

END

NG

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)