Home › Steering › STEERING COLUMN › STEERING LOCK SYSTEM
RM30B0U _55 Steering _010850 STEERING COLUMN _0057945 STEERING LOCK SYSTEM C

STEERING COLUMN  STEERING LOCK SYSTEM  B2788  IG2 Signal Malfunction  


DESCRIPTION

This DTC is stored when the steering lock ECU detects an IG2 power supply malfunction.

HINT:

The steering lock ECU is not connected to the CAN communication system. However, the steering lock ECU is connected to the certification ECU (smart key ECU assembly) via LIN communication and communicates with other components via CAN communication through the certification ECU (smart key ECU assembly).


DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
B2788 IG2 Signal Malfunction Mismatch between the steering lock ECU IG2 input from the LIN communication system and from the direct line (1-trip detection logic*).
·

IGN fuse

·

Steering lock ECU (Steering lock actuator assembly)

·

Harness or connector


No confirmation operation is necessary (monitoring is continuous).

*: Only output while a malfunction is present and the engine switch is on (IG).


Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
The steering cannot be locked or unlocked. For this reason, the engine cannot be started. -

Related Data List and Active Test Items
DTC No. Data List Item Active Test Item
B2788 - -

WIRING DIAGRAM

C240290
4.031,1.615 4.396,1.813 0.365,0.198 10 false IGN 1.229,0.49 1.469,0.698 0.24,0.208 10 false 17 0.26,3.063 0.719,3.26 0.458,0.198 10 false G84 2.74,3.344 4.385,3.531 1.646,0.188 10 false LIN Communication Line 1.771,1.438 2.813,1.677 1.042,0.24 10 false from IG2 Relay 0.271,3.208 1.823,3.573 1.552,0.365 10 false Certification ECU (Smart Key ECU Assembly) 5.344,0.625 5.708,0.823 0.365,0.198 10 false LIN 5.333,1.417 5.625,1.583 0.292,0.167 10 false IG2 5.323,2.208 5.667,2.385 0.344,0.177 10 false GND 5.146,2.104 5.302,2.281 0.156,0.177 10 false 1 5.156,1.323 5.344,1.5 0.188,0.177 10 false 6 5.146,0.469 5.333,0.646 0.188,0.177 10 false 5 4.958,3 5.26,3.198 0.302,0.198 10 false G5 4.969,3.188 6.771,3.552 1.802,0.365 10 false Steering Lock ECU (Steering Lock Actuator Assembly) 0.917,0.646 1.219,0.844 0.302,0.198 10 false LIN

CAUTION / NOTICE / HINT

NOTICE:
·

When using the Techstream with the engine switch off to troubleshoot:

Connect the Techstream to the DLC3 and turn a courtesy light switch on and off at 1.5 second intervals until communication between the Techstream and vehicle begins.

·

The steering lock system uses LIN communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After performing repairs, confirm that no DTCs are output again.

Click hereSteering>STEERING COLUMN>STEERING LOCK SYSTEM>DTC CHECK / CLEAR

·

When replacing the steering lock ECU (steering lock actuator assembly), registration must be performed.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Smart Key System)>REGISTRATION



PROCEDURE

1.INSPECT STEERING LOCK ECU (POWER SOURCE MODE SIGNAL)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the G5 steering lock ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G5-1 (GND) - Body ground Always Below 1 Ω



d.

Reconnect the G5 steering lock ECU connector.


e.
C157849
0.25,0.781 0.74,1.115 0.49,0.333 1.323,1.958 0.76,2.75 false 2.281,1.958 2.781,2.771 false 0.396,0.875 0.677,1.063 0.281,0.188 10 G5 0.208,0.208 0.49,0.396 0.281,0.188 10 *a 0.656,2.771 0.896,2.958 0.24,0.188 10 IG2 2.688,2.813 3.146,3 0.458,0.188 10 GND
*a Component with harness connected
(Steering Lock ECU (Steering Lock Actuator Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G5-6 (IG2) - G5-1 (GND) Engine switch on (IG) 11 to 14 V
G5-6 (IG2) - G5-1 (GND) Engine switch off Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR