The circuit for the side collision sensor LH or RH (to determine deployment of the front seat airbag assembly LH or RH and curtain shield airbag assembly LH or RH) is composed of the airbag sensor assembly, rear airbag sensor LH or RH and door side airbag sensor LH or RH.
The door side airbag sensor LH or RH and rear airbag sensor LH or RH detect impacts to the vehicle and send signals to the airbag sensor assembly to determine if the airbag should be deployed.
DTC B1642/82 or B1647/82 is stored when a malfunction is detected in the circuit for the side satellite sensor bus LH or RH (to determine deployment of the front seat airbag assembly LH or RH and curtain shield airbag assembly LH or RH).
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B1642/81 | Lost Communication with Side Satellite Sensor Bus RH | One of the following conditions is met:
·
The airbag sensor assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the circuit for the side satellite sensor bus RH for 2 seconds. ·
A door side airbag sensor RH malfunction. ·
A rear airbag sensor RH malfunction. ·
An airbag sensor assembly malfunction. |
·
Floor wire ·
Front door wire RH ·
Door side airbag sensor RH ·
Rear airbag sensor RH ·
Airbag sensor assembly |
| B1647/82 | Lost Communication with Side Satellite Sensor Bus LH | One of the following conditions is met:
·
The airbag sensor assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the circuit for the side satellite sensor bus LH for 2 seconds. ·
A door side airbag sensor LH malfunction. ·
A rear airbag sensor LH malfunction. ·
An airbag sensor assembly malfunction. |
·
No. 2 floor wire ·
Front door wire LH ·
Door side airbag sensor LH ·
Rear airbag sensor LH ·
Airbag sensor assembly |
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
After replacing the airbag sensor assembly, refer to initialization.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
Turn the ignition switch to off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| DTC B1642/81 is output |
| DTC B1647/82 is output |
| DTC B1642/81 and B1647/82 are not output |
Codes other than DTC B1642/81 and B1647/82 may be output at this time, but they are not related to this check.
DTC B1642/81 is output
DTC B1647/82 is output
DTC B1642/81 and B1647/82 are not output
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Check that the connectors are properly connected to the airbag sensor assembly and rear airbag sensor RH.
| Proceed to |
|---|
| The connectors are properly connected |
| The connectors are not properly connected |
The connectors are properly connected
The connectors are not properly connected
Disconnect the connectors from the airbag sensor assembly and rear airbag sensor RH.
| *1 | Rear Airbag Sensor RH |
| *2 | Airbag Sensor Assembly |
| *3 | Floor Wire |
Check that the connectors (on the airbag sensor assembly side and rear airbag sensor RH side) are not damaged.
| Proceed to |
|---|
| The connectors are not deformed or damaged |
| The connectors are deformed or damaged |
The connectors are not deformed or damaged
The connectors are deformed or damaged
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
| *1 | Rear Airbag Sensor RH | *2 | Airbag Sensor Assembly |
| *3 | Floor Wire | *4 | Connector C |
| *5 | Connector B | *6 | Service Wire |
| *a | Front view of wire harness connector
(to Rear Airbag Sensor RH) |
*b | Rear view of wire harness connector
(to Airbag Sensor Assembly) |
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| M7-4 (BCR+) - Body ground | Ignition switch ON | Below 1 V |
| M7-3 (BCR-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Using a service wire, connect terminals 24 (BBR+) and 23 (BBR-) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M7-4 (BCR+) - M7-3 (BCR-) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M7-4 (BCR+) - M7-3 (BCR-) | Always | 1 MΩ or higher |
| M7-4 (BCR+) - Body ground | Always | 1 MΩ or higher |
| M7-3 (BCR-) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check that the connector is properly connected to the door side airbag sensor RH.
| Proceed to |
|---|
| The connector is properly connected |
| The connector is not properly connected |
The connector is properly connected
The connector is not properly connected
Disconnect the connector from the door side airbag sensor RH.
| *1 | Door Side Airbag Sensor RH |
| *2 | Rear Airbag Sensor RH |
Check that the connector (on the door side airbag sensor RH side) is not damaged.
| Proceed to |
|---|
| The connector is not deformed or damaged |
| The connector is deformed or damaged |
The connector is not deformed or damaged
The connector is deformed or damaged
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
| *1 | Door Side Airbag Sensor RH | *2 | Rear Airbag Sensor RH |
| *3 | Connector E | *4 | Connector B |
| *5 | Service Wire | - | - |
| *a | Front view of wire harness connector
(to Door Side Airbag Sensor RH) |
*b | Front view of wire harness connector
(to Rear Airbag Sensor RH) |
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| M7-1 (BDR+) - Body ground | Ignition switch ON | Below 1 V |
| M7-2 (BDR-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Using a service wire, connect terminals 2 (BDR+) and 1 (BDR-) of connector E.
Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M7-1 (BDR+) - M7-2 (BDR-) | Always | Below 1 Ω |
Disconnect the service wire from connector E.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M7-1 (BDR+) - M7-2 (BDR-) | Always | 1 MΩ or higher |
| M7-1 (BDR+) - Body ground | Always | 1 MΩ or higher |
| M7-2 (BDR-) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Rear Airbag Sensor LH |
| *2 | Airbag Sensor Assembly |
Connect the connectors to the airbag sensor assembly and door side airbag sensor RH.
Interchange the rear airbag sensor RH with LH and connect the connectors to them.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 90 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| DTC B1647/82 is output |
| DTC B1642/81 is output |
| DTC B1642/81 and B1647/82 are not output |
Codes other than DTC B1642/81 and B1647/82 may be output at this time, but they are not related to this check.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Return the rear airbag sensor LH and RH to their original positions and connect the connectors to them.
DTC B1647/82 is output
DTC B1642/81 is output
DTC B1642/81 and B1647/82 are not output
Disconnect the floor wire connector from the front door wire RH.
| *1 | Door Side Airbag Sensor RH | *2 | Rear Airbag Sensor RH |
| *3 | Front Door Wire RH | *4 | Floor Wire |
| *5 | Connector C | *6 | Connector B |
| *7 | Service Wire | - | - |
| *a | Front view of wire harness connector
(to Front Door Wire RH) |
*b | Front view of wire harness connector
(to Rear Airbag Sensor RH) |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| M7-1 (BDR+) - Body ground | Ignition switch ON | Below 1 V |
| M7-2 (BDR-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Using a service wire, connect terminals 2 (BDR+) and 1 (BDR-) of connector C.
Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M7-1 (BDR+) - M7-2 (BDR-) | Always | Below 1 Ω |
Disconnect the service wire from connector C.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M7-1 (BDR+) - M7-2 (BDR-) | Always | 1 MΩ or higher |
| M7-1 (BDR+) - Body ground | Always | 1 MΩ or higher |
| M7-2 (BDR-) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Door Side Airbag Sensor LH |
| *2 | Rear Airbag Sensor RH |
Interchange the door side airbag sensor RH with LH and connect the connectors to them.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 90 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| DTC B1647/82 is output |
| DTC B1642/81 is output |
| DTC B1642/81 and B1647/82 are not output |
Codes other than DTC B1642/81 and B1647/82 may be output at this time, but they are not related to this check.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Return the door side airbag sensor LH and RH to their original positions and connect the connectors to them.
DTC B1647/82 is output
DTC B1642/81 is output
DTC B1642/81 and B1647/82 are not output
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Check that the connectors are properly connected to the airbag sensor assembly and rear airbag sensor LH.
| Proceed to |
|---|
| The connectors are properly connected |
| The connectors are not properly connected |
The connectors are properly connected
The connectors are not properly connected
Disconnect the connectors from the airbag sensor assembly, rear airbag sensor LH and door side airbag sensor LH.
| *1 | Rear Airbag Sensor LH |
| *2 | Airbag Sensor Assembly |
| *3 | No. 2 Floor Wire |
Check that the connectors (on the airbag sensor assembly side and rear airbag sensor LH side) are not damaged.
| Proceed to |
|---|
| The connectors are not deformed or damaged |
| The connectors are deformed or damaged |
The connectors are not deformed or damaged
The connectors are deformed or damaged
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
| *1 | Rear Airbag Sensor LH | *2 | Airbag Sensor Assembly |
| *3 | No. 2 Floor Wire | *4 | Connector C |
| *5 | Connector B | *6 | Service Wire |
| *a | Front view of wire harness connector
(to Rear Airbag Sensor LH) |
*b | Rear view of wire harness connector
(to Airbag Sensor Assembly) |
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| N9-4 (BCL+) - Body ground | Ignition switch ON | Below 1 V |
| N9-3 (BCL-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Using a service wire, connect terminals 17 (BBL+) and 18 (BBL-) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N9-4 (BCL+) - N9-3 (BCL-) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N9-4 (BCL+) - N9-3 (BCL-) | Always | 1 MΩ or higher |
| N9-4 (BCL+) - Body ground | Always | 1 MΩ or higher |
| N9-3 (BCL-) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check that the connector is properly connected to the door side airbag sensor LH.
| Proceed to |
|---|
| The connector is properly connected |
| The connector is not properly connected |
The connector is properly connected
The connector is not properly connected
Disconnect the connector from the door side airbag sensor LH.
| *1 | Door Side Airbag Sensor LH |
| *2 | Rear Airbag Sensor LH |
Check that the connector (on the door side airbag sensor LH side) is not damaged.
| Proceed to |
|---|
| The connector is not deformed or damaged |
| The connector is deformed or damaged |
The connector is not deformed or damaged
The connector is deformed or damaged
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
| *1 | Door Side Airbag Sensor LH | *2 | Rear Airbag Sensor LH |
| *3 | Connector E | *4 | Connector B |
| *5 | Service Wire | - | - |
| *a | Front view of wire harness connector
(to Door Side Airbag Sensor LH) |
*b | Front view of wire harness connector
(to Rear Airbag Sensor LH) |
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| N9-1 (BDL+) - Body ground | Ignition switch ON | Below 1 V |
| N9-2 (BDL-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Using a service wire, connect terminals 2 (BDL+) and 1 (BDL-) of connector E.
Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N9-1 (BDL+) - N9-2 (BDL-) | Always | Below 1 Ω |
Disconnect the service wire from connector E.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N9-1 (BDL+) - N9-2 (BDL-) | Always | 1 MΩ or higher |
| N9-1 (BDL+) - Body ground | Always | 1 MΩ or higher |
| N9-2 (BDL-) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Rear Airbag Sensor RH |
| *2 | Airbag Sensor Assembly |
Connect the connectors to the airbag sensor assembly and door side airbag sensor LH.
Interchange the rear airbag sensor LH with RH and connect the connectors to them.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 90 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| DTC B1642/81 is output |
| DTC B1647/82 is output |
| DTC B1642/81 and B1647/82 are not output |
Codes other than DTC B1642/81 and B1647/82 may be output at this time, but they are not related to this check.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Return the rear airbag sensor RH and LH to their original positions and connect the connectors to them.
DTC B1642/81 is output
DTC B1647/82 is output
DTC B1642/81 and B1647/82 are not output
Disconnect the No. 2 floor wire connector from the front door wire LH.
| *1 | Door Side Airbag Sensor LH | *2 | Rear Airbag Sensor LH |
| *3 | Front Door Wire LH | *4 | No. 2 Floor Wire |
| *5 | Connector C | *6 | Connector B |
| *7 | Service Wire | - | - |
| *a | Front view of wire harness connector
(to Front Door Wire LH) |
*b | Front view of wire harness connector
(to Rear Airbag Sensor LH) |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| N9-1 (BDL+) - Body ground | Ignition switch ON | Below 1 V |
| N9-2 (BDL-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Using a service wire, connect terminals 3 (BDL+) and 1 (BDL-) of connector C.
Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N9-1 (BDL+) - N9-2 (BDL-) | Always | Below 1 Ω |
Disconnect the service wire from connector C.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N9-1 (BDL+) - N9-2 (BDL-) | Always | 1 MΩ or higher |
| N9-1 (BDL+) - Body ground | Always | 1 MΩ or higher |
| N9-2 (BDL-) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Door Side Airbag Sensor RH |
| *2 | Rear Airbag Sensor LH |
Interchange the door side airbag sensor LH with RH and connect the connectors to them.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 90 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| DTC B1642/81 is output |
| DTC B1647/82 is output |
| DTC B1642/81 and B1647/82 are not output |
Codes other than DTC B1642/81 and B1647/82 may be output at this time, but they are not related to this check.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Return the door side airbag sensor RH and LH to their original positions and connect the connectors to them.
DTC B1642/81 is output
DTC B1647/82 is output
DTC B1642/81 and B1647/82 are not output