Home › Drivetrain › GF1A TRANSFER / 4WD / AWD › DYNAMIC TORQUE CONTROL AWD SYSTEM
RM30B0U _52 Drivetrain _009983 GF1A TRANSFER / 4WD / AWD _0058072 DYNAMIC TORQUE CONTROL AWD SYSTEM C

GF1A TRANSFER / 4WD / AWD  DYNAMIC TORQUE CONTROL AWD SYSTEM  C1299/99  Cancellation of 4WD Control  


DESCRIPTION

This DTC is output if the heat generated by the transmission coupling assembly exceeds a certain amount or if the estimated oil temperature of the transfer exceeds a certain amount while driving.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1299/99 Cancellation of 4WD Control When one of the following conditions is met:
·

Condition that controls coupling calorific value is predefined value or more.

·

Condition that transfer oil temperature is predefined value or more.


·

Condition, size or tire pressure of the front or rear tires

·

Suspension and ball joint

·

Drive shaft

·

Propeller shaft

·

Transmission coupling assembly

·

4WD ECU assembly



CAUTION / NOTICE / HINT

HINT:

Check the condition of each related circuit connector before troubleshooting.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


PROCEDURE

1.CHECK VEHICLE USAGE
a.

Check that there has been no unintended vehicle usage.

OK:

There is no evidence of rough use (the vehicle has not been driven on damaged or snowy roads, etc. for a long time).



Result:
Proceed to
OK
NG



OK

2.CHECK FOR DTC

NG

2.CHECK FOR DTC
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Check if the brake control system DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRAC > Trouble Codes
50001 105

e.

Read the DTCs using the Techstream.

Result:
Result Proceed to
Only "C1299/99" is output A
"C1299/99" and other DTCs (brake control system DTC) B




A

3.CHECK RELATED PART

B

REPAIR CIRCUIT INDICATED BY OUTPUT CODE (BRAKE CONTROL SYSTEM)

3.CHECK RELATED PART
a.

Check the condition, size and tire pressure of the front and rear tires.


b.

Inspect the suspension and ball joint, etc. for rattle.


c.

Inspect the drive shaft and propeller shaft rotation condition.


Result:
Proceed to
OK
NG



OK

4.RECONFIRM DTC

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS

4.RECONFIRM DTC
a.

Clear the DTC.

Click hereDrivetrain>GF1A TRANSFER / 4WD / AWD>DYNAMIC TORQUE CONTROL AWD SYSTEM>DTC CHECK / CLEAR

Chassis > Four Wheel Drive > Clear DTCs
50002 118

b.

Start the engine.


c.

Drive the vehicle at a speed of 20 km/h (12 mph) or more and check that the same DTC is output.

Click hereDrivetrain>GF1A TRANSFER / 4WD / AWD>DYNAMIC TORQUE CONTROL AWD SYSTEM>DTC CHECK / CLEAR

Chassis > Four Wheel Drive > Trouble Codes
50001 118
Result:
Proceed to
DTC is output
DTC is not output




DTC is output

5.REPLACE 4WD ECU ASSEMBLY

DTC is not output

5.REPLACE 4WD ECU ASSEMBLY
a.

Replace the 4WD ECU assembly.

Click hereDrivetrain>GF1A TRANSFER / 4WD / AWD>4WD CONTROL ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.RECONFIRM DTC
6.RECONFIRM DTC
a.

Clear the DTC.

Click hereDrivetrain>GF1A TRANSFER / 4WD / AWD>DYNAMIC TORQUE CONTROL AWD SYSTEM>DTC CHECK / CLEAR

Chassis > Four Wheel Drive > Clear DTCs
50002 118

b.

Start the engine.


c.

Drive the vehicle at a speed of 20 km/h (12 mph) or more and check that the same DTC is output.

Click hereDrivetrain>GF1A TRANSFER / 4WD / AWD>DYNAMIC TORQUE CONTROL AWD SYSTEM>DTC CHECK / CLEAR

Chassis > Four Wheel Drive > Trouble Codes
50001 118
Result:
Proceed to
DTC is output
DTC is not output




DTC is output

REPLACE TRANSMISSION COUPLING ASSEMBLY

DTC is not output

END