Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM30B0U _54 Brake _010842 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0058073 VEHICLE STABILITY CONTROL SYSTEM D

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  TEST MODE PROCEDURE  


WARNING LIGHT AND INDICATOR LIGHT INITIAL CHECK


a.

Release the parking brake.

NOTICE:

When releasing the parking brake, move the shift lever to P to prevent the vehicle from rolling.


HINT:

When the parking brake is applied or the brake fluid level is low, the brake warning light comes on.



b.

When the ignition switch is turned to ON, check that the ABS warning, brake warning, VSC OFF indicator, TRAC OFF indicator, AUTO LSD indicator*, and slip indicator lights come on for approximately 3 seconds.

*: for 2WD


HINT:
·

If the skid control ECU (brake actuator assembly) stores any DTCs, the ABS warning and slip indicator lights will come on.

·

If any of the indicators remain on or do not come on, proceed to troubleshooting for the light circuits listed below.



Trouble Area See Procedure
ABS warning light circuit (Remains on) (Click here)
ABS warning light circuit (Does not come on) (Click here)
Brake warning light circuit (Remains on) (Click here)
Brake warning light circuit (Does not come on) (Click here)
TRAC OFF indicator light circuit (Remains on) (Click here)
TRAC OFF indicator light circuit (Does not come on) (Click here)
VSC OFF indicator light circuit (Remains on) (Click here)
VSC OFF indicator light circuit (Does not come on) (Click here)
Slip indicator light circuit (Remains on) (Click here)
Slip indicator light circuit (Does not come on) (Click here)
AUTO LSD indicator light circuit (Remains on) (Click here)
AUTO LSD indicator light circuit (Does not come on) (Click here)



SENSOR CHECK USING TEST MODE (SIGNAL CHECK) (When Using Techstream)


NOTICE:

After replacement of the brake actuator assembly and/or yaw rate and acceleration sensor (airbag sensor assembly), perform zero point calibration of the yaw rate and acceleration sensor.


HINT:
·

If the ignition switch is turned from ON to ACC or off during Test Mode (signal check), DTCs recorded during the sensor check will be cleared.

·

During Test Mode (signal check), the skid control ECU (brake actuator assembly) records all DTCs detected in the sensor check. By performing Test Mode (signal check), the codes are cleared if a normal condition is confirmed. The remaining codes are the codes indicating where an abnormality was found.



a.

Procedure to enter Test Mode.

i.

Turn the ignition switch off.


ii.

Check that the steering wheel is in the straight-ahead position.


iii.

Check that the shift lever is in P and apply the parking brake.


iv.

Connect the Techstream to the DLC3.


v.

Turn the ignition switch to ON.


vi.

Turn the Techstream on.


vii.

Switch the skid control ECU (brake actuator assembly) to Test Mode using the Techstream.

Enter the following menus: Chassis / ABS/VSC/TRAC / Utility / Signal Check.

Chassis > ABS/VSC/TRAC > Utility
Tester Display
Signal Check
50005 105 1003

viii.

Check that the ABS warning and slip indicator lights come on for several seconds and then blink in the Test Mode blinking pattern (0.125 seconds on and 0.125 seconds off).

HINT:

If the ABS warning and slip indicator lights do not blink, inspect the TS and CG terminal circuit and ABS warning and slip indicator light circuits.


Trouble Area See Procedure
TS and CG terminal circuit (Click here)
ABS warning light circuit (Remains on) (Click here)
ABS warning light circuit (Does not come on) (Click here)
Slip indicator light circuit (Remains on) (Click here)
Slip indicator light circuit (Does not come on) (Click here)




ACCELERATION SENSOR CHECK (When Using Techstream)


a.

Keep the vehicle stationary on a level surface for 1 second or more.

HINT:

The acceleration sensor check can be performed with the master cylinder pressure sensor check below.




MASTER CYLINDER PRESSURE SENSOR CHECK (When Using Techstream)


a.

Leave the vehicle in a stationary condition and release the brake pedal for 1 second or more, and quickly and continuously depress the brake pedal with a force of 98 N (10 kgf, 22 lbf) or more for 1 second.


b.

Check that the ABS warning light stays on for 3 seconds.

HINT:
·

Ensure that the ABS warning light comes on.

·

While the ABS warning light stays on, continue to depress the brake pedal with a force of 98 N (10 kgf, 22 lbf) or more.

·

The ABS warning light comes on for 3 seconds every time the brake pedal operation above is performed.

·

If the master cylinder pressure sensor check is not completed, depressing the brake pedal causes further decreases in vacuum in the brake booster, making the sensor check difficult to complete.

·

If the vacuum is insufficient, the master cylinder pressure sensor check may not be completed. In this case, run the engine at idle to obtain sufficient vacuum.

·

If the brake pedal is strongly depressed when the vacuum is insufficient, the brake warning light may come on in accordance with booster pressure control. In this case, run the engine at idle to obtain sufficient vacuum.





SPEED SENSOR CHECK (When Using Techstream)


a.

Check the speed sensor signal.

NOTICE:

Before performing the speed sensor signal check, complete the acceleration sensor and master cylinder pressure sensor checks.


i.

Drive the vehicle straight ahead.

Accelerate the vehicle to a speed of 45 km/h (28 mph) or more for several seconds and check that the ABS warning light goes off.

·

The sensor check may not be completed if wheelspin occurs.

·

The ABS warning light blinks when the sensor check has been completed and the brake pedal is depressed.

·

The ABS warning light comes on immediately after a malfunction has been detected during the speed sensor check.




b.

Stop the vehicle.

NOTICE:
·

The speed sensor check may not be completed if the sensor check is started with the steering wheel turned or one or more wheels spinning.

·

After the ABS warning light goes off and if the vehicle speed exceeds 80 km/h (50 mph), a sensor check code will be stored again. Decelerate or stop the vehicle before the speed reaches 80 km/h (50 mph).

·

If the sensor check has not been completed, the ABS warning light blinks during driving and the ABS system does not operate.



HINT:

When the sensor check has been completed, the ABS warning light remains off during driving and blinks in the Test Mode pattern while the vehicle is stationary.




TRACTION CONTROL SWITCH CHECK (When Using Techstream)


a.

for AWD:

i.

Check that the TRAC OFF indicator light turns off when the VSC OFF switch (traction control switch) is pressed briefly.



b.

for 2WD:

i.

Check that the AUTO LSD indicator light turns on when the VSC OFF switch (traction control switch) is pressed briefly.



c.

Briefly press the VSC OFF switch (traction control switch) again.



END OF SENSOR CHECK (When Using Techstream)


a.

If the sensor check is completed, the ABS warning light and slip indicator light blink (Test Mode) when the vehicle stops and the ABS warning light is off while the vehicle is being driven.

NOTICE:
·

When the yaw rate sensor, acceleration sensor, speed sensor, and master cylinder pressure sensor checks are completed, the sensor check is completed.

·

If the sensor check is not completed, the ABS warning light blinks even while the vehicle is being driven and the ABS does not operate.





READ DTC OF SIGNAL CHECK FUNCTION (When Using Techstream)


a.

Read the DTC(s) by following the Techstream screen.

NOTICE:
·

If only the DTCs are displayed, repair the malfunction area and clear the DTCs.

·

If Test Mode sensor check DTCs and other DTCs are displayed or if only Test Mode sensor check DTCs are displayed, repair the malfunctions, clear the DTCs, and perform the Test Mode inspection again.




b.

List of DTCs.

ABS Sensor
DTC Code Detection Item Trouble Area
C1271 Low Output Signal of Front Speed Sensor RH
·

Front speed sensor RH

·

Sensor installation

·

Speed sensor rotor


C1272 Low Output Signal of Front Speed Sensor LH
·

Front speed sensor LH

·

Sensor installation

·

Speed sensor rotor


C1273 Low Output Signal of Rear Speed Sensor RH
·

Rear speed sensor RH

·

Sensor installation

·

Speed sensor rotor


C1274 Low Output Signal of Rear Speed Sensor LH
·

Rear speed sensor LH

·

Sensor installation

·

Speed sensor rotor


C1275 Abnormal Change in Output Signal of Front Speed Sensor RH Speed sensor rotor
C1276 Abnormal Change in Output Signal of Front Speed Sensor LH Speed sensor rotor
C1277 Abnormal Change in Output Signal of Rear Speed Sensor RH Speed sensor rotor
C1278 Abnormal Change in Output Signal of Rear Speed Sensor LH Speed sensor rotor
C1279 Acceleration Sensor Output Voltage Malfunction
·

Acceleration sensor (airbag sensor assembly)

·

Sensor installation


C1281 Master Cylinder Pressure Sensor Output Malfunction
·

Stop light switch assembly

·

Master cylinder pressure sensor



HINT:

The codes in this table are output only in Test Mode (signal check).



c.

Turn the ignition switch off and disconnect the Techstream.



SENSOR CHECK USING TEST MODE (SIGNAL CHECK) (When Using SST Check Wire)


NOTICE:

After replacement of the brake actuator assembly and/or yaw rate and acceleration sensor (airbag sensor assembly), perform zero point calibration of the yaw rate and acceleration sensor.


HINT:
·

If the ignition switch is turned from ON to ACC or off during Test Mode (signal check), DTCs recorded during the sensor check will be cleared.

·

During Test Mode (signal check), the skid control ECU (brake actuator assembly) records all DTCs detected in the sensor check. By performing Test Mode (signal check), the codes are cleared if a normal condition is confirmed. The remaining codes are the codes indicating where an abnormality was found.



a.

Procedure to enter Test Mode.

i.

Turn the ignition switch off.


ii.

Check that the steering wheel is in the straight-ahead position.


iii.

Check that the shift lever is in P and apply the parking brake.


iv.
C146309
0.108,0.087 0.413,0.238 0.305,0.151 10 *a 1.63,0.813 1.946,0.3 1.946,0.3 2.07,0.3 false 1.614,1.47 1.303,2.016 1.303,2.016 1.18,2.016 false 2.137,0.207 2.441,0.358 0.305,0.151 10 CG 0.933,1.943 1.238,2.094 0.305,0.151 10 TS
*a Front view of DLC3


Using SST, connect terminals 12 (TS) and 4 (CG) of the DLC3.

SST
09843-18040  


v.

Turn the ignition switch to ON.


vi.

Check that the ABS warning and slip indicator lights come on for several seconds and then blink in Test Mode.

HINT:

If the ABS warning and slip indicator lights do not blink, inspect the TS and CG terminal circuit and ABS warning and slip indicator light circuits.


Trouble Area See Procedure
TS and CG terminal circuit (Click here)
ABS warning light circuit (Remains on) (Click here)
ABS warning light circuit (Does not come on) (Click here)
Slip indicator light circuit (Remains on) (Click here)
Slip indicator light circuit (Does not come on) (Click here)




ACCELERATION SENSOR CHECK (When Using SST Check Wire)


a.

Keep the vehicle stationary on a level surface for 1 second or more.

HINT:

The acceleration sensor check can be performed with the master cylinder pressure sensor check below.




MASTER CYLINDER PRESSURE SENSOR CHECK (When Using SST Check Wire)


a.

Leave the vehicle in a stationary condition and release the brake pedal for 1 second or more, and quickly and continuously depress the brake pedal with a force of 98 N (10 kgf, 22 lbf) or more for 1 second.


b.

Check that the ABS warning light stays on for 3 seconds.

HINT:
·

Ensure that the ABS warning light comes on.

·

While the ABS warning light stays on, continue to depress the brake pedal with a force of 98 N (10 kgf, 22 lbf) or more.

·

The ABS warning light comes on for 3 seconds every time the brake pedal operation above is performed.

·

If the master cylinder pressure sensor check is not completed, depressing the brake pedal causes further decreases in vacuum in the brake booster, making the sensor check difficult to complete.

·

If the vacuum is insufficient, the master cylinder pressure sensor check may not be completed. In this case, run the engine at idle to obtain sufficient vacuum.

·

If the brake pedal is strongly depressed when the vacuum is insufficient, the brake warning light may come on in accordance with booster pressure control. In this case, run the engine at idle to obtain sufficient vacuum.





SPEED SENSOR CHECK (When Using SST Check Wire)


a.

Check the speed sensor signal.

NOTICE:

Before performing the speed sensor signal check, complete the acceleration sensor and master cylinder pressure sensor signal checks.


i.

Drive the vehicle straight ahead.

Accelerate the vehicle to a speed of 45 km/h (28 mph) or more for several seconds and check that the ABS warning light goes off.

·

The sensor check may not be completed if wheelspin occurs.

·

The ABS warning light blinks when the sensor check has been completed and the brake pedal is depressed.

·

The ABS warning light comes on immediately after a malfunction has been detected during the speed sensor check.




b.

Stop the vehicle.

NOTICE:
·

The speed sensor check may not be completed if the sensor check is started with the steering wheel turned or one or more wheels spinning.

·

After the ABS warning light goes off and if the vehicle speed exceeds 80 km/h (50 mph), a sensor check code will be stored again. Decelerate or stop the vehicle before the speed reaches 80 km/h (50 mph).

·

If the sensor check has not been completed, the ABS warning light blinks during driving and the ABS system does not operate.



HINT:

When the sensor check has been completed, the ABS warning light remains on during driving and blinks in the Test Mode pattern while the vehicle is stationary.




TRACTION CONTROL SWITCH CHECK (When Using SST Check Wire)


a.

for AWD:

i.

Check that the TRAC OFF indicator light turns off when the VSC OFF switch (traction control switch) is pressed briefly.



b.

for 2WD:

i.

Check that the AUTO LSD indicator light turns on when the VSC OFF switch (traction control switch) is pressed briefly.



c.

Briefly press the VSC OFF switch (traction control switch) again.



END OF SENSOR CHECK (When Using SST Check Wire)


a.

If the sensor check is completed, the ABS warning light and slip indicator light blink (Test Mode) when the vehicle stops and the ABS warning light is off while the vehicle is being driven.

NOTICE:
·

When the yaw rate sensor, acceleration sensor, speed sensor, and master cylinder pressure sensor checks are completed, the sensor check is completed.

·

If the sensor check is not completed, the ABS warning light will blink even while the vehicle is driven and the ABS will not operate.





READ DTC OF SIGNAL CHECK FUNCTION (When Using SST Check Wire)


a.
C146309
0.108,0.087 0.413,0.238 0.305,0.151 10 *a 1.63,0.813 1.946,0.3 1.946,0.3 2.07,0.3 false 1.614,1.47 1.303,2.016 1.303,2.016 1.18,2.016 false 2.137,0.207 2.441,0.358 0.305,0.151 10 CG 0.933,1.943 1.238,2.094 0.305,0.151 10 TS 1.855,1.47 2.165,2.016 2.165,2.016 2.289,2.016 false 2.338,1.943 2.582,2.094 0.244,0.151 10 TC
*a Front view of DLC3


Using SST, connect terminals 12 (TS), 13 (TC) and 4 (CG) of the DLC3.

SST
09843-18040  


b.

Count the number of blinks of the ABS warning and slip indicator lights.

NOTICE:
·

If only DTCs other than Test Mode sensor check DTCs are displayed, repair the malfunctions and clear the DTCs.

·

If Test Mode sensor check DTCs and other DTCs are displayed or if only Test Mode sensor check DTCs are displayed, repair the malfunctions, clear the DTCs, and perform the Test Mode inspection again.



HINT:
·

When the system is operating correctly, each light will blink continuously in a pattern of 0.25 seconds on, and then 0.25 seconds off.

·

When one DTC is output, each light will output the same code at 4 second intervals (for example, code 21 would be output as 2 flashes, a 1.5 second pause, and then 1 flash).

·

When 2 or more DTCs are output, each light will output a different code at 2.5 second intervals, and when all codes have been output, there will be a 4 second pause and the sequence will repeat.

·

When multiple codes are stored, they are output in order starting with the lowest DTC number.




c.

After performing the check, disconnect SST from terminals TS and CG, and TC and CG of the DLC3 and turn the ignition switch off.


d.

Turn the ignition switch to ON.

HINT:
·

If the ignition switch is not turned to ON after SST is removed from the DLC3, the previous Test Mode will continue.

·

If the ignition switch is turned to ON with terminals TS and CG connected, the previous Test Mode will continue.





DTC OF TEST MODE (SIGNAL CHECK) FUNCTION (When Using SST Check Wire)


ABS Sensor
DTC Code Detection Item Trouble Area
71 Low Output Signal of Front Speed Sensor RH
·

Front speed sensor RH

·

Sensor installation

·

Speed sensor rotor


72 Low Output Signal of Front Speed Sensor LH
·

Front speed sensor LH

·

Sensor installation

·

Speed sensor rotor


73 Low Output Signal of Rear Speed Sensor RH
·

Rear speed sensor RH

·

Sensor installation

·

Speed sensor rotor


74 Low Output Signal of Rear Speed Sensor LH
·

Rear speed sensor LH

·

Sensor installation

·

Speed sensor rotor


75 Abnormal Change in Output Signal of Front Speed Sensor RH Speed sensor rotor
76 Abnormal Change in Output Signal of Front Speed Sensor LH Speed sensor rotor
77 Abnormal Change in Output Signal of Rear Speed Sensor RH Speed sensor rotor
78 Abnormal Change in Output Signal of Rear Speed Sensor LH Speed sensor rotor
79 Acceleration Sensor Output Voltage Malfunction
·

Acceleration sensor (airbag sensor assembly)

·

Sensor installation


81 Master Cylinder Pressure Sensor Output Malfunction
·

Stop light switch assembly

·

Master cylinder pressure sensor



HINT:

The codes in this table are output only in Test Mode (signal check).