Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Smart Key System)
RM30B0U _58 Vehicle Interior _009874 DOOR LOCK _0058013 WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Smart Key System) J

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Smart Key System)  Only Wireless Control Function is Inoperative  


DESCRIPTION

The door control receiver receives signals from the door control transmitter assembly and sends these signals to the main body ECU (multiplex network body ECU). The main body ECU (multiplex network body ECU) then controls all doors by sending lock/unlock signals to each door, and sends hazard flasher signals to the combination meter assembly.

WIRING DIAGRAM

for 12 Pin Type


B342256
2.302,0.969 3.833,1.167 1.531,0.198 10 ECU-B NO.1 3.833,0.823 5.365,1.021 1.531,0.198 10 from Battery 1.75,0.708 3.281,0.906 1.531,0.198 10 7 1.479,0.833 3.01,1.031 1.531,0.198 10 +B 1.781,2.01 3.313,2.208 1.531,0.198 10 4 1.792,2.833 3.323,3.031 1.531,0.198 10 5 1.76,4.115 3.292,4.313 1.531,0.198 10 12 1.365,2.156 2.896,2.354 1.531,0.198 10 RDA 1.354,2.969 2.885,3.167 1.531,0.198 10 PRG 1.542,4.26 3.073,4.458 1.531,0.198 10 E 0.385,4.948 1.917,5.146 1.531,0.198 10 M11 0.396,5.125 1.927,5.323 1.531,0.198 10 Door Control Receiver 5.5,4.958 7.031,5.156 1.531,0.198 10 G78 5.51,5.156 7.156,5.542 1.646,0.385 10 Main Body ECU (Multiplex Network Body ECU) 3.833,4.5 5.365,4.698 1.531,0.198 10 G7 3.844,4.656 5.302,5.031 1.458,0.375 10 Unlock Warning Switch Assembly 3.854,4.146 5.385,4.344 1.531,0.198 10 2 4.792,4.156 6.323,4.354 1.531,0.198 10 1 5.75,4.24 6.365,4.417 0.615,0.177 10 KSW 5.5,4.146 6.115,4.323 0.615,0.177 10 17 5.49,2.031 7.021,2.229 1.531,0.198 10 16 5.552,2.865 7.083,3.063 1.531,0.198 10 4 5.781,2.969 6.875,3.188 1.094,0.219 10 PRG 5.75,2.156 6.281,2.479 0.531,0.323 10 RDA


except 12 Pin Type


B342256
2.302,0.969 3.833,1.167 1.531,0.198 10 ECU-B NO.1 3.833,0.823 5.365,1.021 1.531,0.198 10 from Battery 1.75,0.708 3.281,0.906 1.531,0.198 10 5 1.292,0.833 2.823,1.031 1.531,0.198 10 DATA 1.781,2.01 3.313,2.208 1.531,0.198 10 2 1.792,2.833 3.323,3.031 1.531,0.198 10 3 1.76,4.115 3.292,4.313 1.531,0.198 10 1 1.292,2.156 2.823,2.354 1.531,0.198 10 CSEL 1.354,2.969 2.885,3.167 1.531,0.198 10 PRG 1.375,4.26 2.906,4.458 1.531,0.198 10 GND 0.385,4.948 1.917,5.146 1.531,0.198 10 M10 0.396,5.125 1.927,5.323 1.531,0.198 10 Door Control Receiver 5.5,4.958 7.031,5.156 1.531,0.198 10 G78 5.51,5.156 7.156,5.542 1.646,0.385 10 Main Body ECU (Multiplex Network Body ECU) 3.833,4.5 5.365,4.698 1.531,0.198 10 G7 3.844,4.656 5.302,5.031 1.458,0.375 10 Unlock Warning Switch Assembly 3.854,4.146 5.385,4.344 1.531,0.198 10 2 4.792,4.156 6.323,4.354 1.531,0.198 10 1 5.75,4.24 6.365,4.417 0.615,0.177 10 KSW 5.5,4.146 6.115,4.323 0.615,0.177 10 17 5.49,2.031 7.021,2.229 1.531,0.198 10 16 5.552,2.865 7.083,3.063 1.531,0.198 10 4 5.781,2.969 6.875,3.188 1.094,0.219 10 PRG 5.75,2.156 6.281,2.479 0.531,0.323 10 RDA


CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing or inspecting the door control receiver and wire harness, do not change the position or length of the wire harness. If the wire harness is too close to the door control receiver, wireless function performance may be affected.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION

·

When replacing the door control receiver, read the transmitter IDs (tire pressure warning system) stored in the old ECU using the Techstream and write them down before removal.

·

It is necessary to perform initialization after registration of the transmitter IDs into the door control receiver if the door control receiver has been replaced.

for Initialization:

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION

for Registration:

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION

·

for 12 Pin Type:

First, confirm that there are no malfunctions in the tire pressure warning system. Refer to the How to Proceed with Troubleshooting procedure.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK POWER DOOR LOCK OPERATION
a.

Check the power door lock operation.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK


Result:
Proceed to
Locked doors unlock
Locked doors do not unlock



Locked doors unlock

2.CHECK KEY REMINDER WARNING SYSTEM

Locked doors do not unlock

2.CHECK KEY REMINDER WARNING SYSTEM
a.

Check that the key reminder warning buzzer operates properly.

Click hereVehicle Interior>DOOR LOCK>KEY REMINDER WARNING SYSTEM>OPERATION CHECK


Result:
Proceed to
Key reminder warning buzzer operates properly
Key reminder warning buzzer does not operates properly



Key reminder warning buzzer operates properly

3.CHECK DOOR CONTROL TRANSMITTER ASSEMBLY

Key reminder warning buzzer does not operates properly

3.CHECK DOOR CONTROL TRANSMITTER ASSEMBLY
a.

When a known good registered door control transmitter assembly is used, check that the wireless functions operate properly.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Smart Key System)>OPERATION CHECK


Result:
Result Proceed to
Wireless door lock/unlock/back door open function operates properly with a known good door control transmitter assembly. A
Wireless door lock/unlock/back door open function does not operate. B



A

4.CHECK TRANSMITTER BATTERY (VOLTAGE)

B

5.CHECK WAVE ENVIRONMENT
4.CHECK TRANSMITTER BATTERY (VOLTAGE)


Result:
Proceed to
OK
NG



OK

REPLACE DOOR CONTROL TRANSMITTER ASSEMBLY

NG

5.CHECK WAVE ENVIRONMENT
a.

Bring the door control transmitter assembly near the door control receiver, and perform a wireless operation check.

HINT:
·

When the door control transmitter assembly is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

·

If the inspection result is that the problem only occurs in certain locations or times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.




Result:
Proceed to
Wireless functions operate properly
Wireless functions do not operate properly



Wireless functions operate properly

END (AFFECTED BY WAVE INTERFERENCE)

Wireless functions do not operate properly

6.SWITCH TO SELF-DIAGNOSTIC MODE
6.SWITCH TO SELF-DIAGNOSTIC MODE
a.

Connect the Techstream to the DLC3.


b.

Turn the Ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / Main Body / Utility / Wireless Diagnosis Mode.

Body Electrical > Main Body > Utility
Tester Display
Wireless Door Lock Diagnosis Mode
50005 123 2164

e.

Proceed to the next step in accordance with the prompts on the Techstream screen.


f.
B220865
0.083,0.073 1.76,0.365 1.677,0.292 12 false Interior Light Output: 0.635,1.406 1.063,1.688 0.427,0.281 10 false On 0.635,1.698 1.104,2.01 0.469,0.313 10 false Off 1.552,2.167 1.917,2.5 0.365,0.333 10 false T1 2.146,2.167 2.604,2.604 0.458,0.438 10 false T2 1.979,2.604 3.427,3.042 1.448,0.438 10 false T1: 0.25 seconds 1.979,2.917 3.292,3.313 1.313,0.396 10 false T2: 0.5 seconds 1.802,2.167 2.125,2.51 0.323,0.344 10 false T1

Check that the system has switched to self-diagnostic mode by checking the interior light output pattern.


g.
B220865
0.125,0.104 3,0.667 2.875,0.563 12 false Wireless Door Lock Buzzer Output: 0.625,1.396 1.146,1.698 0.521,0.302 10 false On 0.635,1.688 1.135,2.052 0.5,0.365 10 false Off 1.531,2.167 1.781,2.406 0.25,0.24 10 false T1 2.146,2.167 2.573,2.51 0.427,0.344 10 false T2 1.979,2.583 3.313,2.906 1.333,0.323 10 false T1: 0.13 seconds 1.969,2.896 3.344,3.26 1.375,0.365 10 false T2: 0.25 seconds 1.802,2.167 2.104,2.458 0.302,0.292 10 false T1

Check that the system has switched to self-diagnostic mode by checking the wireless door lock buzzer output pattern.


Result:
Proceed to
NEXT



NEXT

7.CHECK SELF DIAGNOSTIC MODE
7.CHECK SELF DIAGNOSTIC MODE
a.

Inspect the diagnostic outputs when the door control transmitter assembly switch is pressed. The diagnostic outputs can be checked by the flash patterns of the interior light and wireless door lock buzzer patterns.

B163380
0.135,0.094 4.365,0.375 4.229,0.281 12 false Interior Light and Wireless Door Lock Buzzer Output: 0.292,1.333 3.344,1.615 3.052,0.281 10 false (Lock/Unlock/Back Door Open*/Panic Switch): 0.51,1.979 0.906,2.24 0.396,0.26 10 false On 0.51,2.365 0.896,2.583 0.385,0.219 10 false Off 4.125,0.563 6.51,0.938 2.385,0.375 10 false Unmatching Recognition Code (B): 4.26,1.156 4.583,1.385 0.323,0.229 10 false On 4.271,1.552 4.802,1.906 0.531,0.354 10 false Off 4.125,2.917 5.938,3.177 1.813,0.26 10 false No Diagnostic Output (C): 4.198,3.365 4.771,3.698 0.573,0.333 10 false Off 1.25,2.802 1.563,3.01 0.313,0.208 10 false T1 1.76,2.802 2.146,3.063 0.385,0.26 10 false T2 4.938,2.031 6.604,2.344 1.667,0.313 10 false Wave is being received 0.583,3.125 2.969,3.469 2.385,0.344 10 false T1: 0.25 seconds (Interior Light) 0.594,3.813 2.969,4.167 2.375,0.354 10 false T2: 0.5 seconds (Interior Light) 0.292,1.031 1.542,1.281 1.25,0.25 10 false Normal Wave (A) 0.604,4.479 2.76,4.719 2.156,0.24 10 false *: w/ Power Back Door System 0.823,3.448 3.708,3.667 2.885,0.219 10 false 0.13 seconds (Wireless Door Lock Buzzer) 0.833,4.115 3.719,4.333 2.885,0.219 10 false 0.25 seconds (Wireless Door Lock Buzzer)


Result:
Result Proceed to
Normal wave (light flash pattern) is output (A). A
Unmatching recognition code is output (B). B
No diagnostic outputs (C). C



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

8.CHECK REGISTER RECOGNITION CODE

C

9.CHECK DOOR CONTROL RECEIVER (RESPONSE)
8.CHECK REGISTER RECOGNITION CODE
a.

Check that the system can be switched to rewrite mode or add mode, and that a recognition code can be registered.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Smart Key System)>REGISTRATION


Result:
Proceed to
Recognition code can be registered
Recognition code cannot be registered



Recognition code can be registered

END (GO TO OPERATION CHECK)

Recognition code cannot be registered

13.REPLACE DOOR CONTROL RECEIVER
9.CHECK DOOR CONTROL RECEIVER (RESPONSE)
a.

Prepare the door control transmitter assembly from another vehicle.


b.

Press and hold down the door control transmitter assembly switch.


c.

Check that an unmatching recognition code is output.


Result:
Proceed to
Unmatching recognition code is output
Unmatching recognition code is not output



Unmatching recognition code is output

REPLACE DOOR CONTROL TRANSMITTER ASSEMBLY

Unmatching recognition code is not output

10.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - BATTERY AND BODY GROUND)
10.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - BATTERY AND BODY GROUND)
a.
E198671
1.385,0.385 1.802,0.656 0.417,0.271 1.229,1.594 0.865,1.906 0.865,1.906 0.75,1.906 true 2.042,1.615 2.375,1.927 2.375,1.927 2.552,1.927 true 0.073,0.083 0.385,0.281 0.313,0.198 10 *a 1.469,0.427 1.927,0.625 0.458,0.198 10 M11 0.542,1.833 0.854,2.031 0.313,0.198 10 +B 2.625,1.844 3.292,2.042 0.667,0.198 10 E 0.74,0.552 1.052,0.75 0.313,0.198 10 *a
*a Front view of wire harness connector
(to Tire Pressure Warning ECU and Receiver)


for 12 Pin Type:

i.

Disconnect the M11 door control receiver.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M11-12 (E) - Body ground Always Below 1 Ω



iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M11-7 (+B) - Body ground Always 11 to 14 V




b.
B281165
1.49,0.146 1.906,0.375 0.417,0.229 2.594,1.406 2.208,1.406 false 1.219,1.406 0.833,1.406 false 0.125,0.094 0.302,0.24 0.177,0.146 10 *a 0.469,1.333 1.073,1.573 0.604,0.24 10 GND 2.667,1.323 3.146,1.563 0.479,0.24 10 DATA 1.594,0.177 2.427,0.51 0.833,0.333 10 M10
*a Front view of wire harness connector
(to Door Control Receiver)


except 12 Pin Type:

i.

Disconnect the M10 door control receiver.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M10-1 (GND) - Body ground Always Below 1 Ω



iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M10-5 (DATA) - Body ground Always 11 to 14 V




Result:
Proceed to
OK
NG



OK

11.CHECK DOOR CONTROL RECEIVER (OUTPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK DOOR CONTROL RECEIVER (OUTPUT)
a.

for 12 Pin Type:

i.

Connect the M11 door control receiver.


ii.
B274835
1.521,0.292 1.885,0.5 0.365,0.208 0.958,0.552 1.094,0.552 1.094,0.552 1.667,0.99 false 1.563,0.313 2.021,0.51 0.458,0.198 10 M11 0.115,0.094 0.573,0.292 0.458,0.198 10 *a 0.625,0.458 1.083,0.656 0.458,0.198 10 RDA
*a Component with harness connected
(Door Control Receiver)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M11-4 (RDA) - Body ground Ignition switch lock, all doors closed and door control transmitter assembly switch not pressed 11 to 14 V
Ignition switch lock, all doors closed and door control transmitter assembly switch pressed Pulse generation
(0 to 12 V)




b.

except 12 Pin Type:

i.

Connect the M10 door control receiver.


ii.
B281169
1.49,0.375 1.927,0.604 0.438,0.229 1.875,1.281 2.26,1.875 2.26,1.875 2.365,1.875 false 0.24,0.167 0.583,0.49 0.344,0.323 10 *a 2.417,1.792 2.906,1.979 0.49,0.188 10 CSEL 1.594,0.417 1.969,0.594 0.375,0.177 10 M10
*a Component with harness connected
(Door Control Receiver)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M10-2 (CSEL) - Body ground Ignition switch lock, all doors closed and door control transmitter assembly switch not pressed 11 to 14 V
Ignition switch lock, all doors closed and door control transmitter assembly switch pressed Pulse generation
(0 to 12 V)




Result:
Result Proceed to
OK (for 12 Pin Type) A
OK (except 12 Pin Type) B
NG C



A

12.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - DOOR CONTROL RECEIVER)

B

16.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - DOOR CONTROL RECEIVER)

C

REPLACE DOOR CONTROL RECEIVER

12.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - DOOR CONTROL RECEIVER)
a.

Disconnect the G78 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the M11 door control receiver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M11-4 (RDA) - G78-16 (RDA) Always Below 1 Ω
M11-5 (PRG) - G78-4 (PRG) Always Below 1 Ω
M11-4 (RDA) - Body ground Always 10 kΩ or higher
G78-16 (RDA) - Body ground Always 10 kΩ or higher
M11-5 (PRG) - Body ground Always 10 kΩ or higher
G78-4 (PRG) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

13.REPLACE DOOR CONTROL RECEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.REPLACE DOOR CONTROL RECEIVER
a.

Temporarily replace the door control receiver with a new or known good one.

Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL RECEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT

14.CHECK REGISTER RECOGNITION CODE
14.CHECK REGISTER RECOGNITION CODE

Result:
Proceed to
NEXT



NEXT

15.CHECK DOOR CONTROL RECEIVER (OPERATION)
15.CHECK DOOR CONTROL RECEIVER (OPERATION)
a.

Check that the doors can be locked and unlocked by the door control transmitter assembly lock and unlock switches.

OK:

Doors can be locked and unlocked by the door control transmitter assembly.



Result:
Proceed to
OK
NG



OK

END (DOOR CONTROL RECEIVER WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

16.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - DOOR CONTROL RECEIVER)
a.

Disconnect the G78 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the M10 door control receiver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M10-2 (CSEL) - G78-16 (RDA) Always Below 1 Ω
M10-3 (PRG) - G78-4 (PRG) Always Below 1 Ω
M10-2 (CSEL) - Body ground Always 10 kΩ or higher
G78-16 (RDA) - Body ground Always 10 kΩ or higher
M10-3 (PRG) - Body ground Always 10 kΩ or higher
G78-4 (PRG) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

17.REPLACE DOOR CONTROL RECEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.REPLACE DOOR CONTROL RECEIVER
a.

Temporarily replace the door control receiver with a new or known good one.

Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL RECEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT

18.CHECK REGISTER RECOGNITION CODE
18.CHECK REGISTER RECOGNITION CODE

Result:
Proceed to
NEXT



NEXT

19.CHECK DOOR CONTROL RECEIVER (OPERATION)
19.CHECK DOOR CONTROL RECEIVER (OPERATION)
a.

Check that the doors can be locked and unlocked by the door control transmitter assembly lock and unlock switches.

OK:

Doors can be locked and unlocked by the door control transmitter assembly.



Result:
Proceed to
OK
NG



OK

END (DOOR CONTROL RECEIVER WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)