Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)
RM30B0U _59 Vehicle Exterior _010076 WINDOW / GLASS _0058468 POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function) C

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)  B2311  Power Window Motor Malfunction  


DESCRIPTION

The front power window regulator motor assembly LH is operated by the power window regulator master switch assembly. The front power window regulator motor assembly LH has motor and ECU functions.

This DTC is output when the front power window regulator motor assembly LH is malfunctioning, or the ECU built into the front power window regulator motor assembly LH determines that the fully closed window position has deviated approximately 20 mm (0.787 in.) or more from the normal position.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2311 Power Window Motor Malfunction Either condition is met:
·

Front power window regulator motor assembly LH is malfunctioning

·

When ECU in front power window regulator motor assembly LH determines that fully closed window position has deviated approximately 20 mm (0.787 in.) or more from normal position


·

Front power window regulator motor assembly LH

·

Incorrect installation of power window components

·

Overheated front power window regulator motor assembly LH

·

Harness or connector



WIRING DIAGRAM

B344253
5.323,2.781 5.635,2.979 0.313,0.198 10 false J5 2.542,2.813 2.854,3.01 0.313,0.198 10 false J3 1.979,0.51 3.208,0.708 1.229,0.198 10 false P/W MAIN 1.844,1.365 3.073,1.563 1.229,0.198 10 false DOOR D 0.229,0.354 2.677,0.552 2.448,0.198 10 false from POWER Relay 0.448,1.198 2.052,1.406 1.604,0.208 10 false from Battery 3.813,1.083 4.885,1.281 1.073,0.198 10 false AUTO 3.969,1.458 5.042,1.656 1.073,0.198 10 false UP 3.75,1.833 4.823,2.031 1.073,0.198 10 false DOWN 3.854,2.229 4.927,2.427 1.073,0.198 10 false GND 5.427,2.354 6.5,2.552 1.073,0.198 10 false E 5.417,1.979 6.49,2.177 1.073,0.198 10 false D 5.417,1.583 6.49,1.781 1.073,0.198 10 false U 5.417,1.219 6.49,1.417 1.073,0.198 10 false A 5.438,0.365 6.51,0.563 1.073,0.198 10 false B 2.854,1.073 3.927,1.271 1.073,0.198 10 false B 2.604,1.073 3.677,1.271 1.073,0.198 10 false 2 5.146,0.24 6.219,0.438 1.073,0.198 10 false 6 5.167,1.073 6.24,1.271 1.073,0.198 10 false 4 5.156,1.469 6.229,1.667 1.073,0.198 10 false 8 5.146,1.833 6.219,2.031 1.073,0.198 10 false 5 5.167,2.208 6.24,2.406 1.073,0.198 10 false 1 5.313,2.938 6.865,3.323 1.552,0.385 10 false Power Window Regulator Master Switch Assembly 2.552,2.99 4.448,3.385 1.896,0.396 10 false Front Power Window Regulator Motor Assembly LH 4.281,1.458 4.594,1.656 0.313,0.198 10 false 10 4.302,1.073 4.615,1.271 0.313,0.198 10 false 4 4.292,1.823 4.604,2.021 0.313,0.198 10 false 7 4.302,2.229 4.615,2.427 0.313,0.198 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

DTC B2311 is stored in the front power window regulator motor assembly LH.

·

If the front power window regulator motor assembly LH has been replaced with a new one, initialize the power window control system.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)>INITIALIZATION

·

If the front power window regulator motor assembly LH has been removed and installed, or if the front power window regulator motor assembly LH was reused when the door glass or door glass run was replaced, initialize the power window control system.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)>INITIALIZATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK FOR DTC
a.

Clear the DTC.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)>DTC CHECK / CLEAR

Body Electrical > D-Door Motor > Clear DTCs
50002 124

b.

Check for DTCs.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)>DTC CHECK / CLEAR

Body Electrical > D-Door Motor > Trouble Codes
50001 124

Result:
Proceed to
DTC B2311 is not output
DTC B2311 is output



DTC B2311 is not output

DTC B2311 is output

2.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH - BATTERY AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH - BATTERY AND BODY GROUND)
a.
B341203
0.406,0.865 0.719,1.125 0.313,0.26 1.896,0.833 2.125,0.375 2.125,0.375 2.292,0.375 true 1.521,0.813 1.354,0.375 1.354,0.375 1.188,0.375 true 0.875,0.302 1.333,0.5 0.458,0.198 10 false GND 2.365,0.292 2.521,0.49 0.156,0.198 10 false B 0.115,0.104 0.427,0.302 0.313,0.198 10 false *a 0.5,0.927 0.813,1.125 0.313,0.198 10 false J3
*a Front view of wire harness connector
(to Front Power Window Regulator Motor Assembly LH)


Disconnect the front power window regulator motor assembly LH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J3-1 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
J3-2 (B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.PERFORM ACTIVE TEST USING TECHSTREAM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.PERFORM ACTIVE TEST USING TECHSTREAM
a.

Perform the Active Test according to the display on the Techstream.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)>DATA LIST / ACTIVE TEST

CAUTION:

Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function will not operate.


Body Electrical > D-Door Motor > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Power Window Driver door power window OFF, UP or DOWN -
HINT:

Up and down movement does not occur if the arrow is not pressed and held.


Body Electrical > D-Door Motor > Active Test
Tester Display
Power Window
50004 124 1
OK:

Driver door power window motor operates.



Result:
Proceed to
OK
NG



OK

4.PERFORM INITIALIZATION

NG

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

4.PERFORM INITIALIZATION
a.

Initialize the front power window regulator motor assembly LH.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

5.CHECK POWER WINDOW CONTROL SYSTEM
5.CHECK POWER WINDOW CONTROL SYSTEM
a.

Check that the driver door power window operates normally by opening and closing the window.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)>OPERATION CHECK

OK:

Driver door power window motor operates.



Result:
Proceed to
OK
NG



OK

6.CHECK WHETHER PARTS HAVE BEEN INSTALLED CORRECTLY

NG

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

6.CHECK WHETHER PARTS HAVE BEEN INSTALLED CORRECTLY
a.

Check that the power window components are installed correctly.


Result:
Proceed to
Power window components are installed correctly
Power window components are installed incorrectly



Power window components are installed correctly

7.CHECK FOR DTC

Power window components are installed incorrectly

INSTALL PARTS CORRECTLY

7.CHECK FOR DTC
a.

Turn the ignition switch off.


b.

Wait for at least 10 seconds, and then turn the ignition switch to ON.


c.

Check for DTCs.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)>DTC CHECK / CLEAR

Body Electrical > D-Door Motor > Trouble Codes
50001 124

Result:
Proceed to
DTC B2311 is not output
DTC B2311 is output



DTC B2311 is not output

END

DTC B2311 is output

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH