Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)
RM30B0U _59 Vehicle Exterior _010076 WINDOW / GLASS _0058468 POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function) J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)  Driver Side Power Window does not Operate with Power Window Master Switch  


DESCRIPTION

When the ignition switch is ON, the front power window regulator motor assembly LH is operated by the power window regulator master switch assembly. The front power window regulator motor assembly LH has motor and ECU functions.

WIRING DIAGRAM

B344253
5.323,2.781 5.635,2.979 0.313,0.198 10 false J5 2.542,2.813 2.854,3.01 0.313,0.198 10 false J3 1.979,0.51 3.208,0.708 1.229,0.198 10 false P/W MAIN 1.844,1.365 3.073,1.563 1.229,0.198 10 false DOOR D 0.229,0.354 2.677,0.552 2.448,0.198 10 false from POWER Relay 0.448,1.198 2.052,1.406 1.604,0.208 10 false from Battery 3.813,1.083 4.885,1.281 1.073,0.198 10 false AUTO 3.969,1.458 5.042,1.656 1.073,0.198 10 false UP 3.75,1.833 4.823,2.031 1.073,0.198 10 false DOWN 3.854,2.229 4.927,2.427 1.073,0.198 10 false GND 5.427,2.354 6.5,2.552 1.073,0.198 10 false E 5.417,1.979 6.49,2.177 1.073,0.198 10 false D 5.417,1.583 6.49,1.781 1.073,0.198 10 false U 5.417,1.219 6.49,1.417 1.073,0.198 10 false A 5.438,0.365 6.51,0.563 1.073,0.198 10 false B 2.854,1.073 3.927,1.271 1.073,0.198 10 false B 2.604,1.073 3.677,1.271 1.073,0.198 10 false 2 5.146,0.24 6.219,0.438 1.073,0.198 10 false 6 5.167,1.073 6.24,1.271 1.073,0.198 10 false 4 5.156,1.469 6.229,1.667 1.073,0.198 10 false 8 5.146,1.833 6.219,2.031 1.073,0.198 10 false 5 5.167,2.208 6.24,2.406 1.073,0.198 10 false 1 5.313,2.938 6.865,3.323 1.552,0.385 10 false Power Window Regulator Master Switch Assembly 2.552,2.99 4.448,3.385 1.896,0.396 10 false Front Power Window Regulator Motor Assembly LH 4.281,1.458 4.594,1.656 0.313,0.198 10 false 10 4.302,1.073 4.615,1.271 0.313,0.198 10 false 4 4.292,1.823 4.604,2.021 0.313,0.198 10 false 7 4.302,2.229 4.615,2.427 0.313,0.198 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

The power window control system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power window control system after confirming that the communication system is functioning properly.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

If the front power window regulator motor assembly LH has been replaced with a new one, initialize the power window control system.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)>INITIALIZATION

·

When the ECU determines that the front power window regulator motor assembly LH has a malfunction, DTC B2311 is stored.



PROCEDURE

1.CHECK FOR DTC
a.

Clear the DTC.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)>DTC CHECK / CLEAR

Body Electrical > D-Door Motor > Clear DTCs
50002 124

b.

Check for the DTCs.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)>DTC CHECK / CLEAR

Body Electrical > D-Door Motor > Trouble Codes
50001 124

Result:
Result
DTC is not output
DTC is output



DTC is not output

2.PERFORM ACTIVE TEST USING TECHSTREAM

DTC is output

2.PERFORM ACTIVE TEST USING TECHSTREAM
a.

Perform the Active Test according to the display on the Techstream.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)>DATA LIST / ACTIVE TEST

CAUTION:

Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function will not operate.


Body Electrical > D-Door Motor > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Power Window Driver door power window OFF, UP or DOWN -
HINT:

Up and down movement does not occur if the arrow is not pressed and held.


Body Electrical > D-Door Motor > Active Test
Tester Display
Power Window
50004 124 1
OK:

Driver door power window operates normally.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING TECHSTREAM

NG

4.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH - BATTERY AND BODY GROUND)
3.READ VALUE USING TECHSTREAM
a.

Read the Data List according to the display on the Techstream.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)>DATA LIST / ACTIVE TEST

Body Electrical > D-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
D Door P/W Up SW Driver door power window manual up switch signal ON or OFF ON: Driver door power window manual up switch being operated
OFF: Driver door power window manual up switch not being operated
-
D Door P/W Down SW Driver door power window manual down switch signal ON or OFF ON: Driver door power window manual down switch being operated
OFF: Driver door power window manual down switch not being operated
-
Body Electrical > D-Door Motor > Data List
Tester Display
D Door P/W Up SW
D Door P/W Down SW
50003 124 2,3
OK:

On the Techstream screen, ON or OFF is displayed accordingly.



Result:
Proceed to
OK
NG



OK

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

NG

5.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
4.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH - BATTERY AND BODY GROUND)
a.
B341203
0.406,0.865 0.719,1.125 0.313,0.26 1.896,0.833 2.125,0.375 2.125,0.375 2.292,0.375 true 1.521,0.813 1.354,0.375 1.354,0.375 1.188,0.375 true 0.875,0.302 1.333,0.5 0.458,0.198 10 false GND 2.365,0.292 2.521,0.49 0.156,0.198 10 false B 0.115,0.104 0.427,0.302 0.313,0.198 10 false *a 0.5,0.927 0.813,1.125 0.313,0.198 10 false J3
*a Front view of wire harness connector
(to Front Power Window Regulator Motor Assembly LH)


Disconnect the front power window regulator motor assembly LH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J3-1 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
J3-2 (B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
a.

Remove the power window regulator master switch assembly.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL


b.

Inspect the power window regulator master switch assembly.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - BATTERY AND BODY GROUND)
a.
B276330
0.229,0.896 0.479,1.104 0.25,0.208 1.948,1.052 2.167,0.24 2.167,0.24 2.323,0.24 true 1.01,1.021 0.844,0.51 0.844,0.51 0.698,0.51 true 0.302,0.906 0.615,1.104 0.313,0.198 10 false J5 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 2.396,0.156 2.552,0.354 0.156,0.198 10 false B 0.552,0.427 1.073,0.635 0.521,0.208 10 false E
*a Front view of wire harness connector
(to Power Window Regulator Master Switch Assembly)


Disconnect the power window regulator master switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J5-1 (E) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
J5-6 (B) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)
a.

Disconnect the J5 power window regulator master switch assembly connector.


b.

Disconnect the J3 front power window regulator motor assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J5-8 (U) - J3-10 (UP) Always Below 1 Ω
J5-5 (D) - J3-7 (DOWN) Always Below 1 Ω
J5-8 (U) or J3-10 (UP) - Body ground Always 10 kΩ or higher
J5-5 (D) or J3-7 (DOWN) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR