Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)
RM30B0U _59 Vehicle Exterior _010076 WINDOW / GLASS _0058468 POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function) J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)  Driver Side Power Window Auto Up / Down Function does not Operate with Power Window Master Switch  


DESCRIPTION

If the manual up and down function operates normally but the auto up and down function does not, then fail-safe mode may be functioning.

If power window initialization has not been performed, the auto up and down function will not operate.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)>INITIALIZATION

WIRING DIAGRAM

B344253
5.323,2.781 5.635,2.979 0.313,0.198 10 false J5 2.542,2.813 2.854,3.01 0.313,0.198 10 false J3 1.979,0.51 3.208,0.708 1.229,0.198 10 false P/W MAIN 1.844,1.365 3.073,1.563 1.229,0.198 10 false DOOR D 0.229,0.354 2.677,0.552 2.448,0.198 10 false from POWER Relay 0.448,1.198 2.052,1.406 1.604,0.208 10 false from Battery 3.813,1.083 4.885,1.281 1.073,0.198 10 false AUTO 3.969,1.458 5.042,1.656 1.073,0.198 10 false UP 3.75,1.833 4.823,2.031 1.073,0.198 10 false DOWN 3.854,2.229 4.927,2.427 1.073,0.198 10 false GND 5.427,2.354 6.5,2.552 1.073,0.198 10 false E 5.417,1.979 6.49,2.177 1.073,0.198 10 false D 5.417,1.583 6.49,1.781 1.073,0.198 10 false U 5.417,1.219 6.49,1.417 1.073,0.198 10 false A 5.438,0.365 6.51,0.563 1.073,0.198 10 false B 2.854,1.073 3.927,1.271 1.073,0.198 10 false B 2.604,1.073 3.677,1.271 1.073,0.198 10 false 2 5.146,0.24 6.219,0.438 1.073,0.198 10 false 6 5.167,1.073 6.24,1.271 1.073,0.198 10 false 4 5.156,1.469 6.229,1.667 1.073,0.198 10 false 8 5.146,1.833 6.219,2.031 1.073,0.198 10 false 5 5.167,2.208 6.24,2.406 1.073,0.198 10 false 1 5.313,2.938 6.865,3.323 1.552,0.385 10 false Power Window Regulator Master Switch Assembly 2.552,2.99 4.448,3.385 1.896,0.396 10 false Front Power Window Regulator Motor Assembly LH 4.281,1.458 4.594,1.656 0.313,0.198 10 false 10 4.302,1.073 4.615,1.271 0.313,0.198 10 false 4 4.292,1.823 4.604,2.021 0.313,0.198 10 false 7 4.302,2.229 4.615,2.427 0.313,0.198 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

The power window control system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power window control system after confirming that the communication system is functioning properly.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

If the front power window regulator motor assembly LH has been replaced with a new one, initialize the power window control system.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)>INITIALIZATION

·

When the ECU determines that the front power window regulator motor assembly LH has a malfunction, DTC B2311 is stored.



HINT:

If the pulse sensor built into the front power window regulator motor assembly LH is malfunctioning, the power window control system enters fail-safe mode. The remote up and down function cannot be operated during fail-safe mode. However, the power window can be closed by holding the power window regulator master switch assembly at the auto up position, and opened manually by pushing down the power window regulator master switch assembly.


PROCEDURE

1.READ VALUE USING TECHSTREAM
a.

Read the Data List according to the display on the Techstream.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)>DATA LIST / ACTIVE TEST

Body Electrical > D-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
D Door P/W Auto SW Driver door power window auto switch signal ON or OFF ON: Driver door power window auto switch being operated
OFF: Driver door power window auto switch not being operated
-
Body Electrical > D-Door Motor > Data List
Tester Display
D Door P/W Auto SW
50003 124 1
OK:

On the Techstream screen, ON or OFF is displayed accordingly



Result:
Proceed to
OK
NG



OK

2.PERFORM INITIALIZATION

NG

4.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
2.PERFORM INITIALIZATION
a.

Initialize the front power window regulator motor assembly LH.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

3.CHECK POWER WINDOW CONTROL SYSTEM (AUTO UP/DOWN FUNCTION)
3.CHECK POWER WINDOW CONTROL SYSTEM (AUTO UP/DOWN FUNCTION)
a.

Check that the driver door power window moves when the auto up and down function of the power window regulator master switch assembly is operated.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)>OPERATION CHECK

OK:

Driver door auto up and down function is normal.



Result:
Proceed to
OK
NG



OK

END (PROBLEM DUE TO INITIALIZATION FAILURE)

NG

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

4.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
a.

Remove the power window regulator master switch assembly.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL


b.

Inspect the power window regulator master switch assembly.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)

NG

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)
a.

Disconnect the J5 power window regulator master switch assembly connector.


b.

Disconnect the J3 front power window regulator motor assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J5-4 (A) - J3-4 (AUTO) Always Below 1 Ω
J5-4 (A) or J3-4 (AUTO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR