Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART KEY SYSTEM(for Entry Function)
RM30B0U _58 Vehicle Interior _009405 THEFT DETERRENT / KEYLESS ENTRY _0058004 SMART KEY SYSTEM(for Entry Function) C

THEFT DETERRENT / KEYLESS ENTRY  SMART KEY SYSTEM(for Entry Function)  B27A2  Open in Front Passenger Side Electrical Antenna Circuit  


DESCRIPTION

The certification ECU (smart key ECU assembly) generates a request signal and transmits the signal to the front door outside handle assembly (for front passenger door) [electrical key antenna] at intervals of 0.25 seconds. For the front door outside handle assembly (for front passenger door) [electrical key antenna] to detect when the electrical key transmitter sub-assembly is brought close to the vehicle, a signal requesting a response from the electrical key transmitter sub-assembly is transmitted within approximately 1 m (3.28 ft.) of the front passenger door at intervals of 0.25 seconds. DTC B27A2 is stored by the certification ECU (smart key ECU assembly) when an open circuit is detected between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for front passenger door) [electrical key antenna] (between terminals CLG2 and ANT1, or terminals CG2B and ANT2).

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
B27A2 Open in Front Passenger Side Electrical Antenna Circuit An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for front passenger door) (CLG2 - ANT1, CG2B - ANT2) (1 trip detection logic*).
·

Harness or connector

·

Front door outside handle assembly (for front passenger door)

·

Certification ECU (smart key ECU assembly)


Any time

*: Only output while a malfunction is present.

Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Entry lock/unlock operation cannot be performed for front passenger door -

Related Data List and Active Test
DTC Code Data List and Active Test
B27A2 Key diagnostic mode can be used to perform troubleshooting

WIRING DIAGRAM

B341225
0.323,3.479 1.365,3.677 1.042,0.198 10 false I7 1.271,0.719 1.969,0.896 0.698,0.177 10 false ANT1 1.26,1.188 1.958,1.365 0.698,0.177 10 false ANT2 1.542,1.635 2.24,1.813 0.698,0.177 10 false B 1.24,2.094 1.938,2.271 0.698,0.177 10 false SENS 1.24,2.563 1.938,2.74 0.698,0.177 10 false TRG+ 1.323,3.031 2.021,3.208 0.698,0.177 10 false GND 5.75,0.708 6.448,0.885 0.698,0.177 10 false CLG2 5.729,1.156 6.427,1.333 0.698,0.177 10 false CG2B 5.74,1.646 6.438,1.823 0.698,0.177 10 false POS2 5.75,2.083 6.448,2.26 0.698,0.177 10 false SEN2 5.75,2.563 6.448,2.74 0.698,0.177 10 false TSW2 5.729,3.021 6.427,3.198 0.698,0.177 10 false E 5.438,0.552 6.135,0.729 0.698,0.177 10 false 11 5.438,1.021 6.135,1.198 0.698,0.177 10 false 10 5.448,1.469 6.146,1.646 0.698,0.177 10 false 21 5.438,1.938 6.135,2.115 0.698,0.177 10 false 23 5.448,2.396 6.146,2.573 0.698,0.177 10 false 8 5.438,2.854 6.135,3.031 0.698,0.177 10 false 11 5.375,0.729 6.073,0.906 0.698,0.177 10 false G84 5.365,1.188 6.063,1.365 0.698,0.177 10 false G84 5.365,1.646 6.063,1.823 0.698,0.177 10 false G84 5.365,2.115 6.063,2.292 0.698,0.177 10 false G84 5.375,2.573 6.073,2.75 0.698,0.177 10 false G84 5.375,3.031 6.073,3.208 0.698,0.177 10 false G82 1.76,0.604 2.458,0.781 0.698,0.177 10 false 6 1.771,1.073 2.469,1.25 0.698,0.177 10 false 3 1.76,1.542 2.458,1.719 0.698,0.177 10 false 5 1.771,2.01 2.469,2.188 0.698,0.177 10 false 4 1.76,2.458 2.458,2.635 0.698,0.177 10 false 1 1.76,2.927 2.458,3.104 0.698,0.177 10 false 2 0.323,3.635 2.646,4.208 2.323,0.573 10 false Front Door Outside Handle Assembly (for Front Passenger Door) 5.208,3.542 7.104,4.094 1.896,0.552 10 false Certification ECU (Smart Key ECU Assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

The smart key system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART KEY SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart key system (for Entry Function) after confirming that the communication systems are functioning properly.

·

When using the Techstream with the vehicle engine switch off, connect the Techstream to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Smart Key. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the smart key system (for Entry Function) precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART KEY SYSTEM(for Entry Function)>PRECAUTION

·

After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".

·

The front door outside handle assembly (for front passenger door) has an antenna coil between ANT1 and ANT2 terminals.



PROCEDURE

1.CHECK CONNECTOR CONNECTION
a.

Turn the engine switch off.


b.

Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and front door outside handle assembly (for front passenger door).

OK:

Connectors are properly connected.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - FRONT DOOR OUTSIDE HANDLE ASSEMBLY AND BODY GROUND)

NG

CONNECT CONNECTORS PROPERLY

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - FRONT DOOR OUTSIDE HANDLE ASSEMBLY AND BODY GROUND)
a.

Disconnect the G82 and G84 certification ECU (smart key ECU assembly) connectors.


b.

Disconnect the I7 front door outside handle assembly (for front passenger door) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G84-11 (CLG2) - I7-6 (ANT1) Always Below 1 Ω
G84-10 (CG2B) - I7-3 (ANT2) Always Below 1 Ω
G82-11 (E) - Body ground Always Below 1 Ω
I7-2 (E) - Body ground Always Below 1 Ω
G84-11 (CLG2) or I7-6 (ANT1) - Body ground Always 10 kΩ or higher
G84-10 (CG2B) or I7-3 (ANT2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO FRONT PASSENGER SIDE ELECTRICAL KEY ANTENNA)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO FRONT PASSENGER SIDE ELECTRICAL KEY ANTENNA)
a.

Connect the G82 and G84 certification ECU (smart key ECU assembly) connectors.

B271427
2.146,0.594 2.521,0.823 0.375,0.229 4.76,0.594 5.135,0.823 0.375,0.229 2.708,1.51 2.51,2.063 2.51,2.063 2.26,2.063 false 5.177,1.406 5.458,2.375 5.458,2.375 5.76,2.375 false 5.104,1.406 4.823,2.375 4.823,2.375 4.521,2.375 false 0.198,0.146 0.417,0.344 0.219,0.198 10 *a 1.208,2.823 1.427,3.021 0.219,0.198 10 *b 0.969,3.635 1.333,3.802 0.365,0.167 10 GND 3.854,3.635 4.219,3.802 0.365,0.167 10 GND 4.146,2.823 4.365,3.021 0.219,0.198 10 *c 2.156,1.979 2.292,2.146 0.135,0.167 10 E 5.781,2.302 6.188,2.469 0.406,0.167 10 CG2B 4.135,2.292 4.542,2.458 0.406,0.167 10 CLG2 2.219,0.635 2.74,0.906 0.521,0.271 10 G82 4.844,0.635 5.406,0.958 0.563,0.323 10 G84
*a Component with harness connected
(Certification ECU [Smart Key ECU Assembly])
*b Waveform 1
*c Waveform 2 - -



b.

Using an oscilloscope, check the waveform.

OK:
Tester Connection Switch Condition Tool Setting Specified Condition
G84-11 (CLG2) - G82-11 (E)
Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Electrical key transmitter sub-assembly not inside vehicle

5.

Electrical key transmitter sub-assembly brought inside detection area*1

6.

All doors locked through wireless operation


2 V/DIV., 500 ms/DIV. Pulse generation
(See waveform 1)
G84-11 (CLG2) - G82-11 (E)
Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Electrical key transmitter sub-assembly not inside vehicle

5.

Electrical key transmitter sub-assembly brought outside detection area*2

6.

All doors locked through wireless operation


2 V/DIV., 500 ms/DIV. Pulse generation
(See waveform 2)
G84-10 (CG2B) - G82-11 (E)
Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Electrical key transmitter sub-assembly not inside vehicle

5.

All doors locked through wireless operation


2 V/DIV., 500 ms/DIV. Pulse generation
(See waveform 2)


*1: For details about the areas that are inside the entry function detection area, refer to Operation Check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART KEY SYSTEM(for Entry Function)>OPERATION CHECK

Click here

*2: For details about the areas that are outside the entry function detection area, refer to Operation Check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART KEY SYSTEM(for Entry Function)>OPERATION CHECK



Result:
Proceed to
OK
NG



OK

4.REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

4.REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR)
a.

Temporarily replace the front door outside handle assembly (for front passenger door) with a new or known good one.

Click hereVehicle Exterior>DOOR / HATCH>FRONT DOOR>DISASSEMBLY


Result:
Proceed to
NEXT



NEXT

5.CLEAR DTC
5.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART KEY SYSTEM(for Entry Function)>DTC CHECK / CLEAR

Body Electrical > Smart Key > Clear DTCs
50002 125

Result:
Proceed to
NEXT



NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART KEY SYSTEM(for Entry Function)>DTC CHECK / CLEAR

Body Electrical > Smart Key > Trouble Codes
50001 125

Result:
Proceed to
DTC B27A2 is not output
DTC B27A2 is output



DTC B27A2 is not output

END (FRONT DOOR OUTSIDE HANDLE ASSEMBLY [FOR FRONT PASSENGER DOOR] WAS DEFECTIVE)

DTC B27A2 is output

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)