Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART KEY SYSTEM(for Entry Function)
RM30B0U _58 Vehicle Interior _009405 THEFT DETERRENT / KEYLESS ENTRY _0058004 SMART KEY SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  SMART KEY SYSTEM(for Entry Function)  All Door Entry Lock/Unlock Functions do not Operate, but Wireless Functions Operate  


DESCRIPTION

When the wireless operation can be used to lock and unlock the doors, communication between the door control receiver and certification ECU (smart key ECU assembly) is normal. If the entry lock and unlock functions do not operate, the entry cancel function may be set through the customize function, there may be communication problems between the electrical key transmitter sub-assembly and vehicle, or there may be wave interference.

CAUTION / NOTICE / HINT

NOTICE:
·

The smart key system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART KEY SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart key system (for Entry Function) after confirming that the communication systems are functioning properly.

·

When using the Techstream with the vehicle engine switch off, connect the Techstream to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Smart Key. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.

·

Check that there are no electrical key transmitter sub-assemblies in the vehicle.

·

Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Smart Key System)>DTC CHECK / CLEAR

·

Before replacing the certification ECU (smart key ECU assembly) or electrical key transmitter sub-assembly, refer to the smart key system (for Entry Function) precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART KEY SYSTEM(for Entry Function)>PRECAUTION

·

After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".



PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART KEY SYSTEM(for Entry Function)>DTC CHECK / CLEAR

Body Electrical > Smart Key > Trouble Codes
50001 125

Result:
Proceed to
DTC is not output
DTC is output



DTC is not output

2.CHECK WAVE ENVIRONMENT

DTC is output

2.CHECK WAVE ENVIRONMENT
a.

Move the electrical key transmitter sub-assembly as described below and perform the operation inspection.

HINT:
·

When the electrical key transmitter sub-assembly is brought near the front door outside handle assembly (for driver door) or electrical key antenna, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

·

The transmitting wave of the wireless function and entry function are the same, but the wave logic is different. As a result, it is possible that only the wireless function or only the entry function is affected by wave interference.



i.
B340881
1.844,1.094 2.156,1.292 0.313,0.198 10 *a
*a Approximately 0.3 m (0.984 ft.)


Bring the electrical key transmitter sub-assembly approximately 0.3 m (0.984 ft.) from the front door outside handle assembly (for driver door) and perform a driver door entry lock and unlock operation check.

NOTICE:

If the electrical key transmitter sub-assembly is brought within 0.2 m (0.656 ft.) of the door handle, communication may not be possible.



ii.
B340882
1.417,1.073 1.729,1.271 0.313,0.198 10 false *a
*a Approximately 0.3 m (0.984 ft.)


Bring the electrical key transmitter sub-assembly approximately 0.3 m (0.984 ft.) from the front door outside handle assembly (for front passenger door) and perform a front passenger door entry lock and unlock operation check.

NOTICE:

If the electrical key transmitter sub-assembly is brought within 0.2 m (0.656 ft.) of the door handle, communication may not be possible.



iii.
B340888
1.833,1.188 2.146,1.385 0.313,0.198 10 *a
*a Approximately 0.3 m (0.984 ft.)


Bring the electrical key transmitter sub-assembly approximately 0.3 m (0.984 ft.) from the electrical key antenna (outside luggage) and perform a back door open function check.

NOTICE:

If the electrical key transmitter sub-assembly is brought within 0.2 m (0.656 ft.) of the rear bumper, communication may not be possible.


HINT:
·

If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

·

If wave interference seems to be the likely cause of the problem, ask the customer if the problem occurs in specific locations.

·

Move the vehicle to a different location, perform the following procedure and check if the symptoms can be reproduced.

·

If a tool for checking electric waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.





Result:
Proceed to
All operation checks fail
All operation checks are normal
Some operation checks are normal



All operation checks fail

3.CHECK KEY DIAGNOSTIC MODE

All operation checks are normal

AFFECTED BY WAVE INTERFERENCE

Some operation checks are normal

GO TO OTHER PROBLEM (PROCEED TO PROBLEM SYMPTOMS TABLE FOR EACH DOOR)

3.CHECK KEY DIAGNOSTIC MODE
a.

Check the following antennas in key diagnostic mode.


b.

Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.

HINT:

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.


i.
B340881
1.844,1.094 2.156,1.292 0.313,0.198 10 *a
*a 0.7 to 1 m (2.30 to 3.28 ft.)


Check the electrical key antenna (for driver door):

When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the front door outside handle assembly (for driver door), check that the wireless door lock buzzer sounds.

Body Electrical > Smart Key > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 125 1508

ii.
B340882
1.406,1.135 1.719,1.333 0.313,0.198 10 *a
*a 0.7 to 1 m (2.30 to 3.28 ft.)


Check the electrical key antenna (for front passenger door):

When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the front door outside handle assembly (for front passenger door), check that the wireless door lock buzzer sounds.

Body Electrical > Smart Key > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 125 1508

iii.
B340888
1.833,1.188 2.146,1.385 0.313,0.198 10 *a
*a 0.7 to 1 m (2.30 to 3.28 ft.)


Check the electrical key antenna (outside luggage):

When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the electrical key antenna (outside luggage), check that the wireless door lock buzzer sounds.

Body Electrical > Smart Key > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 125 1508

iv.
B340886
0.625,1.156 2.396,0.24 2.396,0.24 2.563,0.24 false 1.75,1.146 2.406,0.24 false 2.594,0.156 2.906,0.354 0.313,0.198 10 *a
*a Inspection Point


Check the No. 1 indoor electrical key antenna (front floor):

When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless door lock buzzer sounds.

Body Electrical > Smart Key > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 125 1508

v.
B340887
0.688,1.052 2.385,0.208 2.385,0.208 2.573,0.208 false 1.688,1.052 2.385,0.208 false 2.615,0.115 2.927,0.313 0.313,0.198 10 *a
*a Inspection Point


Check the No. 2 indoor electrical key antenna (rear floor):

When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless door lock buzzer sounds.

Body Electrical > Smart Key > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 125 1508

vi.
B340884
1.115,1.729 0.75,1.49 0.75,1.49 1.51,1.042 false 0.583,1.396 0.896,1.594 0.313,0.198 10 *a
*a Inspection Point


Check the No. 3 indoor electrical key antenna (inside luggage):

When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless door lock buzzer sounds.

Body Electrical > Smart Key > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 125 1508
OK:

Wireless door lock buzzer sounds.




Result:
Proceed to
All diagnostic mode inspections fail
Some diagnostic mode inspections fail (door)
Some diagnostic mode inspections fail (interior)
Some diagnostic mode inspections fail (outside luggage)
All diagnostic mode inspections are normal



All diagnostic mode inspections fail

4.INSPECT ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

Some diagnostic mode inspections fail (door)

GO TO OTHER PROBLEM (PROCEED TO PROBLEM SYMPTOM TABLE FOR EACH DOOR)

Some diagnostic mode inspections fail (interior)

Some diagnostic mode inspections fail (outside luggage)

All diagnostic mode inspections are normal

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

4.INSPECT ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY
a.

Check if there is another electrical key transmitter sub-assembly available that is already registered to the vehicle.


Result:
Result Proceed to
Another registered electrical key transmitter sub-assembly is not available A
Another registered electrical key transmitter sub-assembly is available B



A

5.ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY REGISTRATION (NEW ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY)

B

6.CHECK ENTRY DOOR LOCK OPERATION
5.ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY REGISTRATION (NEW ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY)
a.

Register a new electrical key transmitter sub-assembly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Smart Key System)>REGISTRATION


Result:
Proceed to
NEXT



NEXT

6.CHECK ENTRY DOOR LOCK OPERATION
6.CHECK ENTRY DOOR LOCK OPERATION
a.

Check the operation of the entry lock function.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART KEY SYSTEM(for Entry Function)>OPERATION CHECK

OK:

Entry lock function operates normally.



Result:
Proceed to
OK
NG



OK

END (ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)