If the entry lock and unlock functions do not operate for the back door only, the request code may not be being transmitted from the back door. If the entry functions for other doors operate properly, communication between the electrical key transmitter sub-assembly and door control receiver is normal. In this case, there may be a problem with request code transmission (communication between the certification ECU [smart key ECU assembly] and electrical key antenna [outside luggage]), or there may be electric wave interference.
The smart key system (for Entry Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART KEY SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING ). Troubleshoot the smart key system (for Entry Function) after confirming that the communication systems are functioning properly.
When using the Techstream with the vehicle engine switch off, connect the Techstream to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Smart Key. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.
Check that there are no electrical key transmitter sub-assemblies in the vehicle.
Before replacing the certification ECU (smart key ECU assembly), refer to the smart key system (for Entry Function) precaution.
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART KEY SYSTEM(for Entry Function)>PRECAUTION
After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
When the entry lock and unlock functions do not operate for doors other than the driver door and if the engine switch has not been turned on (IG) for 14 days or more, lock/unlock the doors using the wireless door lock function or key linked unlock operation and then check if the entry door lock and unlock functions operate.
When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation.
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK
| Proceed to |
|---|
| Door locks operate normally |
| Door locks do not operate |
Door locks operate normally
Door locks do not operate
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
| *a | Approximately 0.3 m (0.984 ft.) |
Bring the electrical key transmitter sub-assembly approximately 0.3 m (0.984 ft.) from the electrical key antenna (outside luggage) and perform an entry back door unlock function check.
If the electrical key transmitter sub-assembly is brought within 0.2 m (0.656 ft.) of the rear bumper, communication may not possible.
If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.
| Proceed to |
|---|
| Entry function does not operate normally |
| Entry function operates normally |
Entry function does not operate normally
Entry function operates normally
Remove the back door opener switch assembly.
Click hereVehicle Exterior>DOOR / HATCH>BACK DOOR OPENER SWITCH>REMOVAL
Inspect back door opener switch assembly.
Click hereVehicle Exterior>DOOR / HATCH>BACK DOOR OPENER SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Back Door Opener Switch Assembly) |
Disconnect the back door opener switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| U7-2 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the following antenna in key diagnostic mode.
| *a | 0.7 to 1 m (2.30 to 3.28 ft.) |
Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.
| Tester Display |
|---|
| Communication Check(Key Diag Mode) |
If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.
Check the electrical key antenna (outside luggage).
When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the electrical key antenna (outside luggage), check that the wireless door lock buzzer sounds.
Wireless door lock buzzer sounds.
| Proceed to |
|---|
| Diagnostic mode inspections fail |
| Diagnostic mode inspections succeed |
Diagnostic mode inspections fail
Diagnostic mode inspections succeed
Disconnect the T2 electrical key antenna (outside luggage) connector.
Disconnect the G83 certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| T2-1 (ANTE8) - G83-2 (CLG8) | Always | Below 1 Ω |
| T2-2 (CLGB) - G83-1 (CG8B) | Always | Below 1 Ω |
| T2-1 (ANTE8) or G83-2 (CLG8) - Body ground | Always | 10 kΩ or higher |
| T2-2 (CLGB) or G83-1 (CG8B) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the electrical key antenna (outside luggage).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (ANTE8) - 2 (CLGB) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG