Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART KEY SYSTEM(for Entry Function)
RM30B0U _58 Vehicle Interior _009405 THEFT DETERRENT / KEYLESS ENTRY _0058004 SMART KEY SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  SMART KEY SYSTEM(for Entry Function)  Back Door Entry Lock Function does not Operate  


DESCRIPTION

If the entry lock function does not operate for the back door only, but the entry unlock function operates, the request code is being transmitted properly from the back door. In this case, there may be a problem related to the lock switch (connection between the back door opener switch assembly and certification ECU [smart key ECU assembly]).

WIRING DIAGRAM

B341296
5.052,1.896 7.104,2.417 2.052,0.521 10 Certification ECU (Smart Key ECU Assembly) 1.042,1.906 3.094,2.427 2.052,0.521 10 Back Door Opener Switch Assembly 1.052,1.719 1.344,1.969 0.292,0.25 10 U7 1.208,1.177 1.375,1.385 0.167,0.208 10 2 1.406,1.167 1.573,1.375 0.167,0.208 10 E 2.563,0.698 2.729,0.906 0.167,0.208 10 L 2.458,1.219 2.698,1.427 0.24,0.208 10 UL 2.75,0.688 2.917,0.896 0.167,0.208 10 1 2.76,1.177 2.927,1.385 0.167,0.208 10 3 5.104,0.708 5.333,0.917 0.229,0.208 10 28 5.115,1.208 5.344,1.417 0.229,0.208 10 27 5.385,0.823 5.99,1.01 0.604,0.188 10 TSW6 5.375,1.333 5.979,1.521 0.604,0.188 10 TSW5 5.052,1.729 5.438,1.927 0.385,0.198 10 G83

CAUTION / NOTICE / HINT

NOTICE:
·

The smart key system (for Entry Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART KEY SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart key system (for Entry Function) after confirming that the communication systems are functioning properly.

·

When using the Techstream with the vehicle engine switch off, connect the Techstream to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Smart Key. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.

·

Check that there are no electrical key transmitter sub-assemblies in the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the smart key system (for Entry Function) precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART KEY SYSTEM(for Entry Function)>PRECAUTION

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.CHECK POWER DOOR LOCK OPERATION
a.

When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK


Result:
Proceed to
Door locks operate normally
Door locks do not operate



Door locks operate normally

2.READ VALUE USING TECHSTREAM (TR/B-DOOR LOCK SW)

Door locks do not operate

2.READ VALUE USING TECHSTREAM (TR/B-DOOR LOCK SW)
a.

Connect the Techstream to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / Smart Key / Data List.


e.

Read the Data List according to the display on the Techstream.

Body Electrical > Smart Key > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Tr/B-Door Lock SW Back door opener switch (lock switch) ON or OFF ON: Back door opener switch (lock switch) pushed
OFF: Back door opener switch (lock switch) not pushed
·

Displays whether the back door opener switch assembly (lock switch) is on or off.

·

Use this Data List item to help determine if there is a switch malfunction when the back door lock function does not operate.


Body Electrical > Smart Key > Data List
Tester Display
Tr/B-Door Lock SW
50003 125 16
OK:

The Techstream display changes correctly in response to the operation of the back door opener switch assembly.



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

3.CHECK HARNESS AND CONNECTOR (BACK DOOR OPENER SWITCH ASSEMBLY - CERTIFICATION ECU)
3.CHECK HARNESS AND CONNECTOR (BACK DOOR OPENER SWITCH ASSEMBLY - CERTIFICATION ECU)
a.

Disconnect the U7 back door opener switch assembly connector.


b.

Disconnect the G83 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
U7-1 (L) - G83-28 (TSW6) Always Below 1 Ω
U7-2 (E) - Body ground Always Below 1 Ω
U7-1 (L) or G83-28 (TSW6) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT BACK DOOR OPENER SWITCH ASSEMBLY (LOCK SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT BACK DOOR OPENER SWITCH ASSEMBLY (LOCK SWITCH)
a.
B142645
1.656,1.396 1.302,1.823 false 2.01,1.406 2.396,1.813 false 1.24,1.854 1.417,2.052 0.177,0.198 10 E 2.417,1.813 2.781,2 0.365,0.188 10 L

Remove the back door opener switch assembly.

Click hereVehicle Exterior>DOOR / HATCH>BACK DOOR OPENER SWITCH>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (L) - 2 (E) No switch pushed 10 kΩ or higher
1 (L) - 2 (E) Lock switch pushed Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE BACK DOOR OPENER SWITCH ASSEMBLY