When the jam protection function activates during power back door operation, one of the following may be the cause: 1) improper fit of back door, or a foreign object is stuck in the back door, 2) malfunctioning power back door sensor assembly circuit or 3) malfunctioning multiplex network door ECU.
Check if there are any foreign objects interfering with back door operation.
| Proceed to |
|---|
| There are no foreign objects |
| There are foreign objects |
There are no foreign objects
There are foreign objects
Check back door operation.
Turn the power back door main switch so that it is not pushed.
Open/close the back door by hand.
| Proceed to |
|---|
| The back door fully opens and closes smoothly |
| The back door fully does not fully open and close smoothly |
The back door fully opens and closes smoothly
The back door fully does not fully open and close smoothly
Check the Data List to determine if the power back door sensor assembly functions properly.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>DATA LIST / ACTIVE TEST
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| PBD Touch Sensor (Right) | Power back door sensor assembly RH signal | ON, OFF or Open | ON: Power back door sensor assembly RH pressed
OFF: Power back door sensor assembly RH not pressed Open: Power back door sensor assembly RH circuit open |
- |
| PBD Touch Sensor (Left) | Power back door sensor assembly LH signal | ON, OFF or Open | ON: Power back door sensor assembly LH pressed
OFF: Power back door sensor assembly LH not pressed Open: Power back door sensor assembly LH circuit open |
- |
| Tester Display |
|---|
| PBD Touch Sensor (Right) |
| PBD Touch Sensor (Left) |
| Result | Proceed to |
|---|---|
| On the Techstream screen, ON or OFF is displayed accordingly | A |
| On the Techstream screen, ON or OFF is not displayed accordingly or Open is displayed for power back door sensor assembly RH | B |
| On the Techstream screen, ON or OFF is not displayed accordingly or Open is displayed for power back door sensor assembly LH | C |
A
B
C
Remove the power back door sensor assembly RH.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR TOUCH SENSOR>REMOVAL
Inspect the power back door sensor assembly RH.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR TOUCH SENSOR>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the U10 power back door sensor assembly RH connector.
Disconnect the U18 multiplex network door ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| U10-1 (OSR) - U18-16 (OSR) | Always | Below 1 Ω |
| U10-2 (OSRE) - U18-17 (OSE) | Always | Below 1 Ω |
| U10-1 (OSR) or U18-16 (OSR) - Body ground | Always | 10 kΩ or higher |
| U10-2 (OSRE) or U18-17 (OSE) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the power back door sensor assembly LH.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR TOUCH SENSOR>REMOVAL
Inspect the power back door sensor assembly LH.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR TOUCH SENSOR>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the U11 power back door sensor assembly LH connector.
Disconnect the U18 multiplex network door ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| U11-1 (OSL) - U18-18 (OSL) | Always | Below 1 Ω |
| U11-2 (OSLE) - U18-17 (OSE) | Always | Below 1 Ω |
| U11-1 (OSL) or U18-18 (OSL) - Body ground | Always | 10 kΩ or higher |
| U11-2 (OSLE) or U18-17 (OSE) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG