Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › from 2013.11
RM30B0U _56 Audio / Visual / Telematics _009009 NAVIGATION / MULTI INFO DISPLAY _0104226 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Illumination Circuit  


DESCRIPTION

Power is supplied to the navigation receiver assembly and steering pad switch assembly illumination when the light control switch is in the tail or head position.

WIRING DIAGRAM

E288799
0.917,0.406 3.208,0.604 2.292,0.198 10 false from TAIL Relay 3.448,0.625 4.115,0.823 0.667,0.198 10 false PANEL 3.99,1.354 4.198,1.531 0.208,0.177 10 false 1 3.99,2.958 4.198,3.135 0.208,0.177 10 false 3 3.958,1.563 4.167,1.74 0.208,0.177 10 false z1 3.958,3.156 4.167,3.333 0.208,0.177 10 false z1 5.042,1.365 5.25,1.542 0.208,0.177 10 false 9 4.99,2.948 5.198,3.125 0.208,0.177 10 false 11 4.99,1.563 5.198,1.74 0.208,0.177 10 false G8 4.99,3.177 5.198,3.354 0.208,0.177 10 false G8 4.417,1.698 4.875,1.875 0.458,0.177 10 false IL+2 4.396,3.292 4.854,3.469 0.458,0.177 10 false -DP 3.75,3.813 5.26,4.177 1.51,0.365 10 false Spiral with Sensor Cable Sub-assembly 4.833,4.969 5.292,5.146 0.458,0.177 10 false 2 4.5,5.073 4.854,5.271 0.354,0.198 10 false ILL- 3.594,5.552 3.948,5.75 0.354,0.198 10 false G16 3.594,5.677 5.531,5.906 1.938,0.229 10 false Combination Meter Assembly 5.698,5.906 6.958,6.25 1.26,0.344 10 false Navigation Receiver Assembly 6.063,5.083 6.417,5.281 0.354,0.198 10 false ILL- 6.031,1.573 6.385,1.771 0.354,0.198 10 false ILL+ 5.604,1.563 5.969,1.74 0.365,0.177 10 false G141 5.615,5.073 5.979,5.25 0.365,0.177 10 false G142 5.75,4.844 6.208,5.021 0.458,0.177 10 false 5 5.719,1.354 6.177,1.531 0.458,0.177 10 false 10 0.865,6.302 2.802,6.531 1.938,0.229 10 false Steering Pad Switch Assembly 0.813,5.844 2.75,6.073 1.938,0.229 10 false Steering Pad Switch RH Side 0.573,3.479 2.51,3.708 1.938,0.229 10 false Steering Pad Switch LH Side

CAUTION / NOTICE / HINT

CAUTION:

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precautionary notice for the Supplemental Restraint System.


NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK ILLUMINATION
a.

Check if the illumination for the navigation receiver assembly, steering pad switch assembly, heater control switch or others (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the head or tail position.

Result:
Result Proceed to
Illumination comes on for all components except steering pad switch assembly. A
Illumination comes on for all components except navigation receiver assembly. B
No illumination comes on (navigation receiver assembly, hazard switch, heater control switch, etc.). C




A

2.CHECK HARNESS AND CONNECTOR (SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY - BATTERY)

B

5.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)

C

2.CHECK HARNESS AND CONNECTOR (SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY - BATTERY)
a.
E270420
1.5,0.25 1.875,0.479 0.375,0.229 1.719,1.542 2.333,1.917 2.333,1.917 2.5,1.917 true 1.313,1.521 0.708,1.906 0.708,1.906 0.531,1.906 true 0.135,1.844 0.521,2.031 0.385,0.188 10 false IL+2 0.083,0.104 0.396,0.302 0.313,0.198 10 false *a 2.635,1.833 3.094,2.031 0.458,0.198 10 false -DP 1.573,0.292 1.885,0.49 0.313,0.198 10 false G8
*a Front view of wire harness connector
(to Spiral with Sensor Cable Sub-assembly)


Disconnect the spiral with sensor cable sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G8-11 (-DP) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G8-9 (IL+2) - Body ground Light control switch in the tail or head position 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT STEERING PAD SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL


b.

Inspect the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

4.INSPECT SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

4.INSPECT SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY
a.

Remove the spiral with sensor cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL


b.

Inspect the spiral with sensor cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION


Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPLACE SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)
a.
E259248
1.51,0.396 1.896,0.594 0.385,0.198 2.333,1.75 2.167,1.75 2.167,1.75 2.073,1.344 true 0.146,0.115 0.458,0.271 0.313,0.156 10 false *a 1.552,0.417 2.104,0.635 0.552,0.219 10 false G141 2.406,1.667 2.958,1.885 0.552,0.219 10 false ILL+
*a Front view of wire harness connector
(to Navigation Receiver Assembly)


Disconnect the navigation receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G141-10 (ILL+) - Body ground Light control switch in the tail or head position 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the G142 navigation receiver assembly connector.


b.

Disconnect the G16 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G142-5 (ILL-) - G16-2 (ILL-) Always Below 1 Ω
G142-5 (ILL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR