Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › from 2013.11
RM30B0U _56 Audio / Visual / Telematics _009009 NAVIGATION / MULTI INFO DISPLAY _0104226 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Reverse Signal Circuit  


DESCRIPTION

The navigation receiver assembly receives a reverse signal from the park/neutral position switch assembly.

WIRING DIAGRAM

E280105
5.625,0.76 6.083,0.958 0.458,0.198 10 false REV 5.427,0.656 5.885,0.854 0.458,0.198 10 false 2 5.51,1.354 5.969,1.552 0.458,0.198 10 false G143 5.531,1.521 6.75,1.917 1.219,0.396 10 false Navigation Receiver Assembly 4.208,0.646 4.667,0.844 0.458,0.198 10 false 2 3.927,0.635 4.385,0.833 0.458,0.198 10 false RL 3,1.104 3.458,1.302 0.458,0.198 10 false B36 3.01,1.271 4.406,1.646 1.396,0.375 10 false Park/Neutral Posistion Switch Assembly 0.313,0.771 1.656,0.979 1.344,0.208 10 false from GAUGE Fuse 3.115,0.667 3.573,0.865 0.458,0.198 10 false 1 3.313,0.635 3.771,0.833 0.458,0.198 10 false RB

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK VEHICLE SIGNAL (OPERATION CHECK)
a.
E278094

Enter the "Vehicle Signal Check Mode" screen. Refer to check Vehicle Signal in Operation Check.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>OPERATION CHECK


b.

Check that the display changes between ON and OFF according to the shift lever position.

OK:
Shift Lever Position Display
R ON
Except R OFF


HINT:

This display is updated once per second. As a result, it is normal for the display to lag behind the actual shift lever position.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK NAVIGATION RECEIVER ASSEMBLY
2.CHECK NAVIGATION RECEIVER ASSEMBLY
a.
E140414
1.417,0.427 1.979,0.75 0.563,0.323 0.938,1.354 0.677,0.917 0.677,0.917 0.563,0.917 true 0.052,0.031 0.313,0.229 0.26,0.198 10 false *a 0.24,0.844 0.594,1.042 0.354,0.198 10 false REV 1.552,0.5 2.156,0.719 0.604,0.219 10 false G143
*a Front view of wire harness connector
(to Navigation Receiver Assembly)


Disconnect the navigation receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G143-2 (REV) - Body ground Ignition switch ON, shift lever in R 7.5 to 14 V
G143-2 (REV) - Body ground Ignition switch ON, shift lever not in R Below 1 V



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Disconnect the G143 navigation receiver assembly connector.


b.

Disconnect the B36 park/neutral position switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G143-2 (REV) - B36-2 (RL) Always Below 1 Ω
G143-2 (REV) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - BATTERY)
a.
E270424
1.479,0.281 1.885,0.51 0.406,0.229 1.073,1.771 1.26,1.771 1.26,1.771 1.625,1.146 true 1.542,0.313 2,0.51 0.458,0.198 10 false B36 0.823,1.698 1.281,1.896 0.458,0.198 10 false RB 0.104,0.083 0.563,0.281 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Park/neutral Position Switch Assembly)


Disconnect the park/neutral position switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B36-1 (RB) - Body ground Ignition switch ON 11 to 14 V


HINT:

If replacing the park/neutral position switch assembly, refer to the procedures below.




Result:
Proceed to
OK
NG



OK

REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR