Home › Engine / Hybrid System › 2AD-FTV INTAKE / EXHAUST › INTAKE MANIFOLD
RM3090E _51 Engine / Hybrid System _008383 2AD-FTV INTAKE / EXHAUST _0046771 INTAKE MANIFOLD A

2AD-FTV INTAKE / EXHAUST  INTAKE MANIFOLD  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the injectors (including shuffling the injectors between the cylinders), common rail, intake manifold or cylinder head, it is necessary to replace the injection pipes with new ones.

·

When replacing the fuel supply pump, common rail, intake manifold or cylinder head, it is necessary to replace the fuel inlet pipe with a new one.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 26100 3.REMOVE DIESEL THROTTLE BODY ASSEMBLY

Hide 25625 5.REMOVE EGR VALVE BRACKET

Hide 16295 6.REMOVE NO. 7 WATER BY-PASS HOSE

a.
A197539

Slide the clamp and remove the No. 7 water by-pass hose from the electric EGR control valve assembly.


Hide 16296 7.DISCONNECT NO. 8 WATER BY-PASS HOSE

Hide 25602 8.REMOVE NO. 2 EGR PIPE SUB-ASSEMBLY

Hide 25800 9.REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY

Hide 23804C 10.REMOVE FUEL INLET PIPE SUB-ASSEMBLY

Hide 23701 11.REMOVE INJECTION PIPE SUB-ASSEMBLY

Hide 23810A 12.REMOVE COMMON RAIL ASSEMBLY

Hide 17853B 13.REMOVE INTAKE MANIFOLD INSULATOR

a.
A197550

Remove the intake manifold insulator from the intake manifold.


Hide 11452 14.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

a.

Remove the engine oil level dipstick.


b.
A291312

Disconnect the connector and detach the wire harness clamp from the engine oil level dipstick guide.


c.

Remove the 2 bolts and engine oil level dipstick guide.


d.

Remove the O-ring from the engine oil level dipstick guide.


Hide 89421C 15.REMOVE DIESEL TURBO PRESSURE SENSOR

Hide 23265 16.REMOVE NO. 1 GAS FILTER

a.
A206311

Disconnect the vacuum hose.


b.

Remove the No. 1 gas filter from the gas filter bracket.


Hide 17696 17.REMOVE GAS FILTER BRACKET

a.
A206312

Remove the 2 bolts and gas filter bracket.


Hide 12631A 18.REMOVE ENGINE COVER BRACKET

a.
A197556

Remove the bolt and engine cover bracket.


Hide 17112 19.REMOVE NO. 2 INTAKE MANIFOLD

a.
A197557

Remove the bolt, 2 nuts, No. 2 intake manifold and gasket.


Hide 25770A 20.DISCONNECT NO. 2 VACUUM TRANSMITTING HOSE ASSEMBLY

a.
A201877

Slide the clamp and disconnect the No. 2 vacuum transmitting hose assembly from the intake manifold.


Hide 17111 21.REMOVE INTAKE MANIFOLD

a.
A197558C02
0.583,1.875 0.896,2.031 0.313,0.156 10 *1
*1 Nut


Remove the 7 bolts, 2 nuts, intake manifold and gasket.


Hide 22.REMOVE STUD BOLT

HINT:

If a stud bolt is deformed or the threads are damaged, replace it.