Home › Engine / Hybrid System › 2AD-FTV ENGINE CONTROL › ECD SYSTEM(for DPF)
RM3090E _51 Engine / Hybrid System _008377 2AD-FTV ENGINE CONTROL _0046807 ECD SYSTEM(for DPF) J

2AD-FTV ENGINE CONTROL  ECD SYSTEM(for DPF)  MIL Circuit  


DESCRIPTION

The MIL (Malfunction Indicator Lamp) is used to indicate vehicle malfunctions detected by the ECM. When the ignition switch is turned to ON, power is supplied to the MIL circuit, and the ECM provides the circuit ground which illuminates the MIL.

The MIL operation can be checked visually. When the ignition switch is first turned to ON, the MIL should be illuminated and should then turn off when the engine is started. If the MIL remains illuminated or is not illuminated, conduct the following troubleshooting procedure using the GTS.

WIRING DIAGRAM

A206938E09
6.177,2.396 6.49,2.552 0.313,0.156 10 false A61 6.177,2.531 6.573,2.688 0.396,0.156 10 false ECM 6.042,1.021 6.26,1.177 0.219,0.156 10 false W 5.781,1.229 5.979,1.385 0.198,0.156 10 false 12 4.948,1 5.146,1.156 0.198,0.156 10 false 11 3.406,2.021 3.708,2.177 0.302,0.156 10 false G16 2.802,0.99 3,1.146 0.198,0.156 10 false 39 3.719,1.302 4.01,1.469 0.292,0.167 10 false MIL 4.542,1.25 5.031,1.573 0.49,0.323 10 false CHK 3.052,1.26 3.344,1.427 0.292,0.167 10 false IG+ 1.896,0.958 2.438,1.125 0.542,0.167 10 false METER 3.396,2.156 4.646,2.323 1.25,0.167 10 false Combination Meter 1.969,1.281 2.083,1.448 0.115,0.167 10 false 1 0.479,1.125 1.458,1.292 0.979,0.167 10 false from IG2 Relay 2.281,1.281 2.396,1.448 0.115,0.167 10 false 2

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION) and initialization (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).


PROCEDURE

1.CHECK THAT MIL IS ILLUMINATED
a.

Perform troubleshooting in accordance with the table below.

Result:
Proceed to
MIL remains on
MIL does not illuminate




MIL remains on

2.CHECK WHETHER DTC OUTPUT RECURS

MIL does not illuminate

5.CHECK THAT MIL IS ILLUMINATED
2.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

e.

Check if any DTCs have been detected. Note down any DTCs.

Result:
Proceed to
No DTC detected
Any DTCs detected


HINT:

Check for detected DTCs output from other ECUs which relate to the MIL.




No DTC detected

3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)

Any DTCs detected

3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
a.

Disconnect the A61 ECM connector.


b.

Turn the ignition switch to ON.


c.

Check that the MIL is not illuminated.

OK:

MIL is not illuminated.



Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.

Disconnect the combination meter assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G16-11 (CHK) or A61-12 (W) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK THAT MIL IS ILLUMINATED
a.

Check if the MIL is illuminated when the ignition switch is turned to ON.

OK:

MIL should be illuminated.



Result:
Proceed to
OK
NG



OK

NG

6.CHECK THAT ENGINE STARTS
6.CHECK THAT ENGINE STARTS
a.

Turn the ignition switch to ON.


b.

Start the engine.

Result:
Proceed to
Engine starts
Engine does not start*


HINT:

*: The GTS cannot communicate with the ECM.




Engine starts

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)

Engine does not start*

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.

Disconnect the combination meter assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G16-11 (CHK) - A61-12 (W) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR