The ECM constantly generates 5 V of power from the battery voltage supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.
When the VC circuit is short-circuited, the microprocessor in the ECM and sensors that are supplied with power through the VC circuit are inactivated because the power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.
Under normal conditions, the MIL is illuminated for several seconds when the ignition switch is first turned ON. The MIL goes off when the engine is started.
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION) and initialization (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).
Check that the Malfunction Indicator Lamp (MIL) lights up when turning the ignition switch to ON.
| Proceed to |
|---|
| MIL does not illuminate |
| MIL illuminates |
MIL does not illuminate
MIL illuminates
Connect the GTS to the DLC3.
Turn the ignition switch to ON and GTS on.
Check the communication between the GTS and ECM.
| Proceed to |
|---|
| Communication is not possible |
| Communication is possible |
Communication is not possible
Communication is possible
Disconnect the accelerator pedal sensor assembly connector.
Turn the ignition switch to ON.
Check the MIL.
| Proceed to |
|---|
| MIL does not illuminate |
| MIL illuminates |
MIL does not illuminate
MIL illuminates
Disconnect the diesel throttle body assembly connector.
Turn the ignition switch to ON.
Check the MIL.
| Proceed to |
|---|
| MIL does not illuminate |
| MIL illuminates |
MIL does not illuminate
MIL illuminates
Disconnect the fuel pressure sensor connector.
Turn the ignition switch to ON.
Check the MIL.
| Proceed to |
|---|
| MIL does not illuminate |
| MIL illuminates |
MIL does not illuminate
MIL illuminates
Disconnect the electric EGR valve assembly connector.
Turn the ignition switch to ON.
Check the MIL.
| Proceed to |
|---|
| MIL does not illuminate |
| MIL illuminates |
MIL does not illuminate
MIL illuminates
Disconnect the differential pressure sensor assembly connector.
Turn the ignition switch to ON.
Check the MIL.
| Proceed to |
|---|
| MIL does not illuminate |
| MIL illuminates |
MIL does not illuminate
MIL illuminates
Click hereEngine / Hybrid System>2AD-FTV EMISSION CONTROL>DIFFERENTIAL PRESSURE SENSOR(for DPF)>REMOVAL
Disconnect the manifold absolute pressure sensor connector.
Turn the ignition switch to ON.
Check the MIL.
| Proceed to |
|---|
| MIL does not illuminate |
| MIL illuminates |
MIL does not illuminate
MIL illuminates
Disconnect the battery current sensor connector.
Turn the ignition switch to ON.
Check the MIL.
| Proceed to |
|---|
| MIL does not illuminate |
| MIL illuminates |
MIL does not illuminate
MIL illuminates
Disconnect the accelerator pedal sensor assembly connector.
Disconnect the diesel throttle body assembly connector.
Disconnect the fuel pressure sensor connector.
Disconnect the electric EGR control valve assembly connector.
Disconnect the differential pressure sensor assembly connector.
Disconnect the manifold absolute pressure sensor connector.
Disconnect the battery current sensor connector.
Disconnect the ECM connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A61-55 (VCPA) - Body ground | Always | 10 kΩ or higher |
| A61-57 (VCP2) - Body ground | Always | 10 kΩ or higher |
| B76-97 (VCVL) - Body ground | Always | 10 kΩ or higher |
| B76-68 (VCM) - Body ground | Always | 10 kΩ or higher |
| B76-69 (VCS) - Body ground | Always | 10 kΩ or higher |
| B76-94 (VCEG) - Body ground | Always | 10 kΩ or higher |
| B76-93 (VCPM) - Body ground | Always | 10 kΩ or higher |
| B76-75 (VCIB) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG