Home › Engine / Hybrid System › 2AD-FTV ENGINE CONTROL › ECD SYSTEM(for DPF)
RM3090E _51 Engine / Hybrid System _008377 2AD-FTV ENGINE CONTROL _0046807 ECD SYSTEM(for DPF) C

2AD-FTV ENGINE CONTROL  ECD SYSTEM(for DPF)  P0093  Fuel System Leak Detected - Large Leak  


DESCRIPTION

A fuel pressure sensor mounted on the common rail converts the fuel pressure inside the common rail into an electric signal, and outputs it to the ECM. The ECM controls the supply pump in order to maintain the fuel pressure inside the common rail at a target pressure calculated by the ECM.

Refer to System Description (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>SYSTEM DESCRIPTION).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0093 Fuel System Leak Detected - Large Leak Fuel pressure drop before and after fuel injection is larger than the threshold a certain number of times (0.2 seconds or more).
(1 trip detection logic)
·

Fuel line between supply pump assembly and common rail assembly

·

Fuel line between common rail assembly and injector assembly

·

Supply pump assembly

·

Pressure discharge valve (built into common rail assembly)

·

Fuel pressure sensor (built into common rail assembly)

·

Injector assembly

·

Crankshaft position sensor

·

Fuel filter assembly

·

Open or short in injector driver (EDU) circuit (P0201, P0202, P0203, P0204 and/or P062D set simultaneously)

·

Open or short in injector assembly circuit (P0201, P0202, P0203, P0204 and/or P062D set simultaneously)

·

Injector driver (EDU) (P0201, P0202, P0203, P0204 and/or P062D set simultaneously)

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P0093
·

Fuel Press

·

Target Common Rail Pressure



HINT:
·

For more information on the common rail system, refer to System Description (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>SYSTEM DESCRIPTION).

·

If DTC P0093 is present, refer to the Diagnostic Trouble Code Chart (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>DIAGNOSTIC TROUBLE CODE CHART).

·

When DTC P0093 is set, check the internal fuel pressure of the common rail by entering the following menus on the GTS: Powertrain / Engine and ECT / Data List / Fuel Press and Target Common Rail Pressure.

Reference
Engine Speed Fuel Pressure
Idling Approximately 27000 to 45000 kPa
3000 rpm (No engine load) Approximately 45000 to 78000 kPa

·

When there is an operating problem with the fuel supply pump (Fuel Press is less than Target Common Rail Pressure), the values of Injection Pressure Correction and Target Pump SCV Current will increase.



MONITOR DESCRIPTION

P0093 (Fuel leaks in high-pressure areas):

This DTC indicates that fuel leaks exist in the common rail system. The ECM constantly monitors the internal fuel pressure of the common rail after the engine is started. The ECM stores this DTC if the drop in the internal fuel pressure is large when the fuel is injected.

In the common rail system, high-pressure fuel is always supplied to the high-pressure areas including the fuel supply pump, common rail, fuel injectors and piping. The ECM adjusts the suction control valve opening angle to obtain the desired fuel pressure.

If this DTC is stored, the ECM enters fail-safe mode. The fail-safe mode suspends both fuel injection and fuel supply pump operation, and then stops the engine. Before stopping the engine, the ECM permits the vehicle to be driven for 60 seconds. The fail-safe mode continues until the ignition switch is turned off.


MONITOR STRATEGY

Required Sensor Fuel pressure sensor
Frequency of operation Continuous
Duration 1 second
MIL operation 1 driving cycle

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0093 After idling for 60 seconds, run engine at 2500 rpm for 30 seconds.
Fully depress the accelerator pedal for 5 seconds, and then release it. (*A)
Rev the engine to 3000 rpm and fully release the accelerator pedal immediately after the engine reaches 3000 rpm. (*B)
Repeat procedures (*A) and (*B) 5 times.

CAUTION / NOTICE / HINT

NOTICE:
·

Soon after starting the engine, visually check for fuel leaks in the fuel line.

·
·

After replacing the supply pump assembly, the ECM needs initialization (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).

·

After replacing a fuel injector, the ECM needs registration (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION).



HINT:

Read freeze frame data (multi freeze frame data) using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


A206075E06
3.823,4.208 3.448,3.573 false 3.823,4.208 3.448,4.625 false 0.125,0.938 1.469,1.135 1.344,0.198 10 Engine Speed (rpm) 0.125,2.458 2.052,2.667 1.927,0.208 10 Fuel Press (kPa) 0.125,4.125 2.417,4.323 2.292,0.198 10 Target Common Rail Pressure (kPa) 0.125,5.688 1.76,5.885 1.635,0.198 10 Injection Volume (mm3/st) 1.344,2.198 1.469,2.365 0.125,0.167 10 0 1.115,1.75 1.469,1.917 0.354,0.167 10 1000 1.125,1.302 1.469,1.458 0.344,0.156 10 2000 1.323,3.792 1.427,3.979 0.104,0.188 10 0 1.021,3.333 1.427,3.49 0.406,0.156 10 32500 1.01,2.885 1.427,3.052 0.417,0.167 10 65000 1.323,5.344 1.427,5.531 0.104,0.188 10 0 1.01,4.885 1.417,5.042 0.406,0.156 10 35000 1,4.438 1.417,4.604 0.417,0.167 10 70000 1.333,6.948 1.438,7.135 0.104,0.188 10 0 1.063,6.5 1.427,6.656 0.365,0.156 10 60.00 0.979,6.052 1.427,6.219 0.448,0.167 10 120.00 0.104,0.073 4.313,0.25 4.208,0.177 10 This is snapshot data which was taken when P0093 was stored (1): 3.385,3.896 3.531,4.083 0.146,0.188 10 A 3.396,2.313 3.542,2.5 0.146,0.188 10 A 3.396,7.052 3.542,7.24 0.146,0.188 10 A 3.396,5.479 3.542,5.667 0.146,0.188 10 A 3.844,4.156 4.042,4.354 0.198,0.198 10 *1 0.104,0.417 6.427,0.604 6.323,0.188 10 DTC P0093 was stored due to a decrease in fuel pressure when the accelerator pedal was depressed. 2.583,7.052 2.771,7.24 0.188,0.188 10 A'

HINT:

*1: Common Rail Pressure suddenly decreases for a moment, and then recovers. This can be seen clearly by comparing it to Target Common Rail Pressure.


A206076E02
4.583,4.156 4.135,3.25 false 1.333,2.198 1.438,2.385 0.104,0.188 10 0 1.021,1.74 1.427,1.896 0.406,0.156 10 50.00 0.958,1.292 1.427,1.458 0.469,0.167 10 100.00 1.063,3.802 1.427,3.99 0.365,0.188 10 -10.0 1.323,3.344 1.438,3.5 0.115,0.156 10 0 1.125,2.896 1.427,3.063 0.302,0.167 10 10.0 0.229,0.833 1.51,1.031 1.281,0.198 10 Accel Position (%) 0.229,2.552 2.458,2.698 2.229,0.146 10 Injection Feedback Val #3 (mm3/st) 0.073,0.073 4.313,0.281 4.24,0.208 10 This is snapshot data which was taken when P0093 was stored (2): 1.146,5.344 1.448,5.531 0.302,0.188 10 OFF 1.188,5 1.438,5.156 0.25,0.156 10 ON 0.208,4.156 0.51,4.302 0.302,0.146 10 MIL 3.375,3.938 3.51,4.125 0.135,0.188 10 A 3.385,2.323 3.521,2.51 0.135,0.188 10 A 3.385,5.479 3.521,5.667 0.135,0.188 10 A 4.5,4.156 4.719,4.313 0.219,0.156 10 *2 0.073,0.417 6.417,0.604 6.344,0.188 10 DTC P0093 was stored due to a decrease in fuel pressure when the accelerator pedal was depressed

HINT:

*2: Injection Feedback Val #3 is 5.0 mm3/st which is large (the normal value is between -3.0 and 3.0 mm3/st) and indicates that the injector of cylinder 3 may be malfunctioning.


Reference Values for DTC P0093 Storage Point (Point A)
Data List Value Unit
Engine Speed 1478 rpm
Fuel Press 8900 kPa
Target Common Rail Pressure 65320 kPa
Injection Volume (Point A) 51.26*1 mm3/st
Injection Volume (Point A`) 9.76 mm3/st
Accel Position 63.67 %
Injection Feedback Val #1 -1.1 mm3/st
Injection Feedback Val #2 -2.5 mm3/st
Injection Feedback Val #3 5.0 mm3/st
Injection Feedback Val #4 -1.8 mm3/st
MIL ON -

PROCEDURE

1.CHECK FUEL LEAK (IN HIGH-PRESSURE AREAS)
a.

Before starting the engine, visually check for fuel leaks from the supply pump assembly, injector assemblies, common rail assembly and the fuel pipes in high-pressure areas.

OK:

No fuel leaks in high-pressure areas.



Result:
Proceed to
OK
NG



OK

2.CHECK ANY OTHER DTCS OUTPUT (PROCEDURE 2) (IN ADDITION TO DTC P0093) AND RECORD STORED DTC AND FREEZE FRAME DATA

NG

REPAIR OR REPLACE FUEL LEAK POINT

2.CHECK ANY OTHER DTCS OUTPUT (PROCEDURE 2) (IN ADDITION TO DTC P0093) AND RECORD STORED DTC AND FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

d.

Read the DTCs and freeze frame data.

Result:
Result Proceed to
Except below A
DTC P0093 and "P0335 and/or P0339" are output B
DTC P0093 and "P0190, P0192 and/or P0193" are output C




A

3.CHECK FUEL RECEIVER GAUGE (AMOUNT OF FUEL)

B

GO TO CRANKSHAFT POSITION SENSOR "A" CIRCUIT (DTC P0335 AND P0339)

C

GO TO FUEL RAIL PRESSURE SENSOR CIRCUIT (DTC P0190, P0192 AND P0193)

3.CHECK FUEL RECEIVER GAUGE (AMOUNT OF FUEL)
a.

Check if the fuel level is low.

Result:
Proceed to
The indicator (fuel warning light) is illuminated
The indicator (fuel warning light) is not illuminated




The indicator (fuel warning light) is illuminated

4.ADD FUEL

The indicator (fuel warning light) is not illuminated

6.CHECK FREEZE FRAME DATA (INJECTION FEEDBACK VAL #1 TO #4)
4.ADD FUEL
a.

Add fuel.


Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (DTC P0093)
5.CHECK WHETHER DTC OUTPUT RECURS (DTC P0093)
a.
A271186

Using the hand pump mounted on the fuel filter cap, bleed the air from the fuel system. Continue pumping until the pump resistance increases.

NOTICE:
·

Hand pump pumping speed: Max. 2 strokes/sec.

·

The hand pump must be pushed with a full stroke during pumping.

·

When the fuel pressure at the supply pump inlet port reaches a saturated pressure, the hand pump resistance increases.

·

If pumping is interrupted during the air bleeding process, fuel in the fuel line may return to the fuel tank. Continue pumping until the hand pump resistance increases.

·

If the hand pump resistance does not increase despite consecutively pumping 200 times or more, there may be a fuel leak between the fuel tank and fuel filter element assembly, the hand pump may be malfunctioning, or the vehicle may have run out of fuel.

·

If a large amount of air remains inside the fuel system, the common rail pressure does not rise to the pressure range necessary for normal use, and the engine cannot be started.




b.

Start the engine.

NOTICE:
·

If a large amount of air remains inside the fuel system, the starter may need to be cranked for 10 seconds or more to start the engine.

·

Do not crank the engine continuously for more than 20 seconds. The battery may be discharged.

·

Use a fully-charged battery.



i.

When the engine can be started, proceed to the next step.


ii.

If the engine cannot be started, bleed the air again using the hand pump until the hand pump resistance increases. Then start the engine.



c.

Turn the ignition switch off.


d.

Connect the GTS to the DLC3.


e.

Turn the ignition switch to ON and turn the GTS on.


f.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

g.

Start the engine. (*A)


h.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak. (*B)


i.

Perform the following test 5 times with on/off intervals of 10 seconds: Active Test / Test the Fuel Leak. (*C)


j.

Allow the engine to idle for 3 minutes or more after performing the Active Test for the fifth time. (*D)

A192848E03
0.177,1.313 1.583,1.583 1.406,0.271 10 false Active Test Operation 6.5,2.313 6.896,2.49 0.396,0.177 10 false Time 1.677,0.969 2.042,1.167 0.365,0.198 10 false ON 1.646,1.625 2.073,1.823 0.427,0.198 10 false OFF 2.563,1.927 3.375,2.094 0.813,0.167 10 false 10 seconds 3.188,0.656 4,0.823 0.813,0.167 10 false 10 seconds 2.635,0.24 3.229,0.417 0.594,0.177 10 false 1st time 3.896,0.24 4.5,0.427 0.604,0.188 10 false 2nd time 5.198,0.24 5.792,0.406 0.594,0.167 10 false 5th time 5.99,1.865 6.75,2.083 0.76,0.219 10 false 3 minutes


k.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

l.

Read the Current DTCs.

i.

When no DTCs are output, the air bleeding is completed.


ii.

If any DTCs are output, proceed to the next step.



m.

Repeat steps (*A) to (*D).


n.

Clear the DTCs.

Powertrain > ECT > Clear DTCs
50002 64

o.

Start the engine and warm it up.


p.

Confirm that the shift lever is in neutral and securely apply the parking brake.


q.

Fully depress the accelerator pedal for 5 seconds, and then release it. (*E)


r.

Rev the engine to 3000 rpm and fully release the accelerator pedal immediately after the engine reaches 3000 rpm. (*F)


s.

Repeat procedures (*E) and (*F) 5 times.

A220593E02
1.631,1.808 2.016,1.984 0.385,0.177 10 5000 1.47,0.54 1.965,0.717 0.495,0.177 10 160000 5.134,2.085 5.771,2.262 0.637,0.177 10 3000 rpm 1.868,2.501 1.996,2.678 0.128,0.177 10 0 1.858,1.171 1.986,1.347 0.128,0.177 10 0 0.072,0.778 1.026,0.948 0.955,0.170 10 Fuel Pressure 0.081,2.12 1.036,2.290 0.955,0.170 10 Engine Speed 0.081,3.416 1.251,3.586 1.170,0.170 10 Accelerator Pedal 0.944,3.043 2.106,3.235 1.162,0.193 10 Fully Depressed 1.022,3.687 2.002,3.880 0.980,0.193 10 Fully Released 2.855,4.175 3.552,4.365 0.698,0.191 10 5 seconds 6.453,4.089 6.856,4.280 0.403,0.191 10 Time 3.102,2.914 3.724,3.150 0.622,0.236 10 Step (*E) 6.212,2.914 6.810,3.150 0.598,0.236 10 Step (*E) 4.75,2.914 5.376,3.150 0.626,0.236 10 Step (*F) 2.101,0.529 2.370,0.719 0.268,0.190 10 kPa 2.078,1.718 2.393,1.879 0.315,0.162 10 rpm


t.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

u.

Read the Current DTCs.

Result:
Proceed to
DTC is output
DTC is not output




DTC is output

6.CHECK FREEZE FRAME DATA (INJECTION FEEDBACK VAL #1 TO #4)

DTC is not output

DTC CAUSED BY RUNNING OUT OF FUEL

6.CHECK FREEZE FRAME DATA (INJECTION FEEDBACK VAL #1 TO #4)
a.

Read the value of Injection Feedback Val #1 to #4 in the Freeze Frame Data recorded in Procedure 2.

Result:
Result Proceed to
Except below A
Injection Feedback Val for at least one cylinder is 5.0 mm3/st in at least 1 set of freeze frame data B


HINT:

When there is a problem with the operation of an injector assembly due to foreign matter in the inside of the injector assembly, etc., the fuel injection volume decreases. As a result, the ECM gives instructions to increase the fuel injection volume, which causes Injection Feedback Val to increase.




A

7.READ VALUE USING GTS (FUEL PRESS)

B

10.REPLACE FUEL FILTER ELEMENT ASSEMBLY
7.READ VALUE USING GTS (FUEL PRESS)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press.

Powertrain > Engine > Data List
Tester Display
Fuel Press
50003 61 54

e.

Start the engine.


f.

Read the value of Fuel Press while cranking and idling the engine.

Result:
Result Proceed to
Except below A
The engine cannot be started or the engine can be started but Fuel Press is less than 20000 kPa 2 seconds after the starter signal changes from off to on. B




A

8.READ VALUE USING GTS (INJECTION FEEDBACK VAL #1 TO #4)

B

14.INSPECT INJECTOR ASSEMBLY (INSPECTION FOR VALVE CLOSING PROBLEM)
8.READ VALUE USING GTS (INJECTION FEEDBACK VAL #1 TO #4)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine and warm it up.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Injection Feedback Val #1 to #4.

Powertrain > Engine > Data List
Tester Display
Injection Feedback Val #1
Injection Feedback Val #2
Injection Feedback Val #3
Injection Feedback Val #4
50003 61 368,369,370,371

e.

Read the values.

Standard:
Tester Display Engine Condition* Normal Value
Injection Feedback Val #1
Injection Feedback Val #2
Injection Feedback Val #3
Injection Feedback Val #4
Idling -3.0 mm3/st to 3.0 mm3/st


HINT:

*: The A/C switch and all accessory switches should be off, the engine coolant temperature should be 75°C (167°F) or higher and the engine should be idled for 1 minute or more.


Result:
Result Proceed to
Except below A
Injection Feedback Val for at least one cylinder is more than 3.0 mm3/st and engine vibration is abnormally large B


HINT:
·

When there is a problem with the operation of an injector assembly due to foreign matter in the inside of the injector assembly, etc., the fuel injection volume decreases. As a result, the ECM gives instructions to increase the fuel injection volume, which causes Injection Feedback Val to increase.

·

The ECM controls the system so that the sum of Injection Feedback Val for all of the cylinders is approximately 0 mm3/st. Even if the value of Injection Feedback Val for a cylinder is less than -3.0 mm3/st (-3.0 mm3/st is the lowest normal value), as long as the value of Injection Feedback Val for each of the other cylinders is 3.0 mm3/st or less, the injector assemblies are not malfunctioning.





A

9.PERFORM ENGINE SPEED ACCELERATION

B

10.REPLACE FUEL FILTER ELEMENT ASSEMBLY
9.PERFORM ENGINE SPEED ACCELERATION
a.

Start the engine and drive the vehicle until the engine coolant temperature reaches 60°C (140°F) or higher.


b.

Stop the vehicle and allow the engine to idle.


c.

While checking the tachometer, fully depress the accelerator pedal for 5 seconds, and then release it [A].


d.

Repeat procedure [A] 5 times.

Result:
Result Proceed to
No problems such as sluggishness or variations in the tachometer reading A
Except above B




A

10.REPLACE FUEL FILTER ELEMENT ASSEMBLY

B

18.READ VALUE USING GTS (ENGINE SPEED)
10.REPLACE FUEL FILTER ELEMENT ASSEMBLY
a.

Replace the fuel filter element assembly.

Click hereEngine / Hybrid System>2AD-FTV FUEL>FUEL FILTER>REPLACEMENT


Result:
Proceed to
NEXT



NEXT

11.BLEED AIR FROM FUEL SYSTEM
11.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>2AD-FTV FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

12.PERFORM ACTIVE TEST USING GTS (TEST THE FUEL LEAK)
12.PERFORM ACTIVE TEST USING GTS (TEST THE FUEL LEAK)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak / Fuel Press, Target Common Rail Pressure, and Target Pump SCV Current.

Powertrain > Engine > Active Test
Active Test Display
Test the Fuel Leak
Data List Display
Target Common Rail Pressure
Fuel Press
Target Pump SCV Current
50004 61 90 706,54,408

d.

Start the engine.


e.

Take a snapshot with the GTS during the Active Test.


f.

Measure the difference between the target fuel pressure (Target Common Rail Pressure) and the actual fuel pressure (Fuel Press) when the "Test the Fuel Leak" Active Test is performed.

HINT:

In order to obtain an exact measurement, perform the Active Test 5 times and measure the difference once each time the Active Test is performed.


A227749E05
3.604,2.406 3.719,1.927 3.719,1.927 3.792,1.927 false 4.604,2.563 4.948,2.302 4.948,2.302 5,2.302 false 3.042,1.375 3.01,1.281 3.01,1.281 3.063,1.281 false 6.229,1.375 6.198,1.281 6.198,1.281 6.25,1.281 false 4.771,1.375 4.75,1.281 4.75,1.281 4.802,1.281 false 3.521,2.542 3.24,1.896 3.24,1.896 3.188,1.896 false 3.573,3.24 3.823,4.281 3.823,4.281 3.969,4.281 false 0.083,1.417 1.448,1.573 1.365,0.156 10 Active Test Operation 0.083,0.583 1.479,0.781 1.396,0.198 10 Engine Speed (rpm) 0.083,3.25 1.677,3.49 1.594,0.24 10 Fuel Press 3.813,1.865 5.75,2.031 1.938,0.167 10 Target Common Rail Pressure 6.469,4.125 6.865,4.302 0.396,0.177 10 Time 2.125,2.406 2.865,2.771 0.74,0.365 10 Less than 10000 kPa 3,4.26 3.688,4.427 0.688,0.167 10 2 seconds 5.021,2.208 6.302,2.583 1.281,0.375 10 Abnormal Common Rail Pressure 2.448,1.115 3.125,1.313 0.677,0.198 10 Test Start 4.177,1.115 4.844,1.313 0.667,0.198 10 Test Stop 5.625,1.115 6.302,1.313 0.677,0.198 10 Test Start 2.083,1.813 3.229,2.135 1.146,0.323 10 Normal Common Rail Pressure 1.646,0.271 2.021,0.438 0.375,0.167 10 2000 1.885,0.833 2.052,1 0.167,0.167 10 0 1.75,1.302 2.073,1.469 0.323,0.167 10 ON 1.698,1.552 2.021,1.719 0.323,0.167 10 OFF 3.99,4.219 6.302,4.573 2.313,0.354 10 Pressure Discharge Valve Abnormal Common Rail Pressure

OK:

The difference between the target fuel pressure and the actual fuel pressure 2 seconds after the Active Test starts is less than 10000 kPa.


HINT:
·

"Target Common Rail Pressure" means target fuel pressure controlled by the ECM.

·

"Fuel Press" is the actual fuel pressure in common rail assembly.



Result:
Result Proceed to
The difference between the target fuel pressure and the actual fuel pressure 2 seconds after the Active Test starts is less than 10000 kPa A
Except above B




A

13.PERFORM ACTIVE TEST USING GTS (CONTROL THE SELECT CYLINDER FUEL CUT)

B

14.INSPECT INJECTOR ASSEMBLY (INSPECTION FOR VALVE CLOSING PROBLEM)
13.PERFORM ACTIVE TEST USING GTS (CONTROL THE SELECT CYLINDER FUEL CUT)
HINT:

Use this Active Test to determine the malfunctioning cylinder.


a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Select Cylinder Fuel Cut / #1 to #4.

HINT:
·

If the engine idle speed does not change when an injector assembly is disabled, the cylinder being tested is malfunctioning. Record any malfunctioning cylinders.

·

If the cylinder being tested is normal, there will be a significant change in idle speed when the injection assembly is stopped for that cylinder.



Powertrain > Engine > Active Test
Tester Display
Control the Select Cylinder Fuel Cut
50004 61 231

Result:
Proceed to
NEXT



NEXT

15.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER
14.INSPECT INJECTOR ASSEMBLY (INSPECTION FOR VALVE CLOSING PROBLEM)
a.

Remove the glow plug assembly for all the cylinders.

Click hereEngine / Hybrid System>2AD-FTV STARTING>GLOW PLUG>REMOVAL


b.

Visually check if there is fuel on the glow plug assemblies.

HINT:
·

If there is fuel on a glow plug assembly, fuel may be leaking from an injector assembly.

·

After replacing an injector assembly, make sure that the common rail pressure (fuel pressure) is within 5000 kPa (51.0 kgf/cm2, 725 psi) of the target fuel pressure while cranking the engine.

·

If there is fuel on a glow plug assembly, fuel may have mixed with the engine oil. Check the engine oil amount and whether the engine oil smells of diesel fuel. If the oil level is above the full line or the engine oil smells of diesel fuel, replace the engine oil.




Result:
Proceed to
NEXT



NEXT

15.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER
15.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER
a.

Replace the injector assembly of the malfunctioning cylinder.

Click hereEngine / Hybrid System>2AD-FTV FUEL>FUEL INJECTOR>REMOVAL

NOTICE:
·

When replacing the injector assembly for a cylinder, always be sure to use a new injection pipe.

·

Follow the procedure in the repair manual and temporarily install the injection pipes and nozzle leakage pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe may become incomplete, resulting in a fuel leak.



Result:
Proceed to
NEXT




NEXT

16.BLEED AIR FROM FUEL SYSTEM
16.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>2AD-FTV FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

17.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
17.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
a.

Register the injector compensation code.

Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION


b.

Result:
Proceed to
NEXT



NEXT

23.CHECK WHETHER DTC OUTPUT RECURS (DTC P0093)
18.READ VALUE USING GTS (ENGINE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.

Powertrain > Engine > Data List
Tester Display
Engine Speed
50003 61 315

d.

Read the value while cranking and idling the engine.

Standard:
Tester Display Engine Condition Specified Condition
Engine Speed Cranking 50 to 400 rpm
Idling with warm engine 750 to 850 rpm


HINT:

The value is the same as the actual engine speed and is displayed with no interruption on the GTS.



Result:
Proceed to
OK
NG



OK

19.CHECK HARNESS AND CONNECTOR

NG

28.REPLACE CRANKSHAFT POSITION SENSOR
19.CHECK HARNESS AND CONNECTOR
HINT:

If the MIL has illuminated before in the past, clear the DTC using the GTS before performing this inspection.

Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>DTC CHECK / CLEAR


A194532C01
0.75,2.188 0.354,2.469 0.354,2.469 0.354,2.677 false 1.292,1.323 1.625,3.24 1.625,3.24 1.813,3.24 true 1.542,0.344 1.854,0.5 0.313,0.156 10 *1 0.292,2.719 0.604,2.875 0.313,0.156 10 *2 1.854,3.177 2.167,3.333 0.313,0.156 10 *3 3.729,1.135 4.042,1.292 0.313,0.156 10 *4 5.833,1.104 6.146,1.26 0.313,0.156 10 *5 0.125,0.104 0.438,0.26 0.313,0.156 10 *a
*1 Engine *2 Engine Wire
*3 Common Rail Assembly
(Fuel Pressure Sensor)
*4 Wire to Wire
*5 ECM - -
*a Vibration Method (Reference) - -


a.

Check if the MIL illuminates up when vibration is applied to the wire harness and connectors between the fuel pressure sensor and ECM.

OK:

The MIL does not come on.


Result:
Proceed to
MIL does not come on
MIL comes on




MIL does not come on

20.INSPECT FUEL TEMPERATURE SENSOR (SENSOR OUTPUT)

MIL comes on

24.REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - FUEL PRESSURE SENSOR)
20.INSPECT FUEL TEMPERATURE SENSOR (SENSOR OUTPUT)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Temperature.

Powertrain > Engine > Data List
Tester Display
Fuel Temperature
50003 61 403

d.

Read the value.

OK:

The value is almost the same as the actual fuel temperature.


HINT:

When the engine is stopped and left overnight, the fuel temperature becomes the same as the atmospheric temperature.



Result:
Proceed to
OK
NG



OK

21.CHECK FOR INTERMITTENT PROBLEMS

NG

22.REPLACE FUEL TEMPERATURE SENSOR
21.CHECK FOR INTERMITTENT PROBLEMS

Result:
Proceed to
NEXT



NEXT

23.CHECK WHETHER DTC OUTPUT RECURS (DTC P0093)
22.REPLACE FUEL TEMPERATURE SENSOR
a.

Replace the fuel temperature sensor.

Click hereEngine / Hybrid System>2AD-FTV FUEL>FUEL TEMPERATURE SENSOR>REMOVAL

HINT:

Before replacing the fuel temperature sensor, perform a wire harness inspection and if there are any problems with the wire harness, repair or replace it.



Result:
Proceed to
NEXT



NEXT

23.CHECK WHETHER DTC OUTPUT RECURS (DTC P0093)
23.CHECK WHETHER DTC OUTPUT RECURS (DTC P0093)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch off and wait for 30 seconds or more.


f.

Start the engine and warm it up (engine coolant temperature is 75°C (167°F) or higher).


g.

Confirm that the shift lever is in neutral and securely apply the parking brake.


h.

Fully depress the accelerator pedal for 5 seconds and then release it [A].


i.

Rev the engine to 3000 rpm and fully release the accelerator pedal immediately after the engine reaches 3000 rpm [B].


j.

Repeat the above procedures [A] and [B] 5 times.

A196453E13
4.615,3.146 4.802,2.979 4.802,2.979 4.917,2.979 false 1.646,1.823 2.031,2 0.385,0.177 10 5000 1.51,0.552 2,0.729 0.49,0.177 10 100000 5.156,2.104 5.594,2.281 0.438,0.177 10 3000 1.896,2.51 2.021,2.688 0.125,0.177 10 0 1.885,1.188 2.01,1.365 0.125,0.177 10 0 0.094,0.792 1.5,0.958 1.406,0.167 10 Fuel Pressure [kPa] 0.115,2.135 1.521,2.302 1.406,0.167 10 Engine Speed [rpm] 0.104,3.427 1.271,3.594 1.167,0.167 10 Accelerator Pedal 0.969,3.052 2.135,3.25 1.167,0.198 10 Fully Depressed 1.042,3.698 2.021,3.896 0.979,0.198 10 Fully Released 2.875,4.188 3.573,4.375 0.698,0.188 10 5 seconds 6.479,4.104 6.885,4.292 0.406,0.188 10 Time 3.125,2.896 3.354,3.135 0.229,0.24 10 [A] 4.948,2.896 5.177,3.135 0.229,0.24 10 [B] 6.5,2.896 6.729,3.135 0.229,0.24 10 [A]


k.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

l.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

24.REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - FUEL PRESSURE SENSOR)
a.

Repair or replace the harness or connector (ECM - fuel pressure sensor).


Result:
Proceed to
NEXT



NEXT

25.CHECK HARNESS AND CONNECTOR
25.CHECK HARNESS AND CONNECTOR
HINT:

If the MIL has illuminated before in the past, clear the DTC using the GTS before performing this inspection.

Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>DTC CHECK / CLEAR


A194532C01
0.75,2.188 0.354,2.469 0.354,2.469 0.354,2.677 false 1.292,1.323 1.625,3.24 1.625,3.24 1.813,3.24 true 1.542,0.344 1.854,0.5 0.313,0.156 10 *1 0.292,2.719 0.604,2.875 0.313,0.156 10 *2 1.854,3.177 2.167,3.333 0.313,0.156 10 *3 3.729,1.135 4.042,1.292 0.313,0.156 10 *4 5.833,1.104 6.146,1.26 0.313,0.156 10 *5 0.125,0.104 0.438,0.26 0.313,0.156 10 *a
*1 Engine *2 Engine Wire
*3 Common Rail Assembly
(Fuel Pressure Sensor)
*4 Wire to Wire
*5 ECM - -
*a Vibration Method (Reference) - -


a.

Check if the MIL illuminates up when vibration is applied to the wire harness and connectors between the fuel pressure sensor and ECM.

OK:

The MIL does not come on.


Result:
Proceed to
MIL does not come on
MIL comes on




MIL comes on

26.REPLACE COMMON RAIL ASSEMBLY

MIL does not come on

23.CHECK WHETHER DTC OUTPUT RECURS (DTC P0093)
26.REPLACE COMMON RAIL ASSEMBLY
a.

Replace the common rail assembly.

Click hereEngine / Hybrid System>2AD-FTV FUEL>COMMON RAIL>REMOVAL


Result:
Proceed to
NEXT



NEXT

27.BLEED AIR FROM FUEL SYSTEM
27.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>2AD-FTV FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

23.CHECK WHETHER DTC OUTPUT RECURS (DTC P0093)
28.REPLACE CRANKSHAFT POSITION SENSOR
a.

Replace the crankshaft position sensor.

Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>CRANKSHAFT POSITION SENSOR>REMOVAL

HINT:

Before replacing the crankshaft position sensor, perform a wire harness inspection and if there are any problems with the wire harness, repair or replace it.



Result:
Proceed to
NEXT



NEXT

23.CHECK WHETHER DTC OUTPUT RECURS (DTC P0093)