12108
1.REMOVE OIL FILLER CAP SUB-ASSEMBLY
Remove the oil filler cap sub-assembly.
12108A
2.REMOVE OIL FILLER CAP GASKET
Remove the oil filler cap gasket.
12635
3.REMOVE ENGINE COVER JOINT
Remove the 2 engine cover joints.
19100P
4.REMOVE SPARK PLUG
11101W
5.REMOVE CAMSHAFT POSITION SENSOR (for Intake Side)
6.REMOVE CAMSHAFT POSITION SENSOR (for Exhaust Side)
11101J
7.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Intake Side)
8.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Exhaust Side)
11401G
9.REMOVE CRANKSHAFT POSITION SENSOR
83530
10.REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY
89615
11.REMOVE KNOCK SENSOR
89422
12.REMOVE ENGINE COOLANT TEMPERATURE SENSOR
11201
13.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY
Remove the 13 bolts, seal washer and cylinder head cover sub-assembly.
Remove the 3 gaskets from the camshaft bearing cap.
As gaskets may stick to the cylinder head cover, be careful not to drop any of the gaskets into the engine when removing the cylinder head cover.
11213
14.REMOVE CYLINDER HEAD COVER GASKET
Remove the cylinder head cover gasket.
11193
15.REMOVE SPARK PLUG TUBE GASKET
Pry up the 4 claws of the ventilation baffle plate.
Do not deform the claws of the ventilation baffle plate more than necessary.
Using a screwdriver as shown in the illustration, deform each spark plug tube gasket inwards and remove the 4 spark plug tube gaskets from cylinder head cover sub-assembly.
As much as possible prevent the spark plug tube gaskets from being deformed.
The removed spark plug tube gaskets will be used when reinstalling the new spark plug tube gaskets.
Do not damage the cylinder head cover sub-assembly.
Make sure not to damage the spark plug tube gasket and cylinder head cover sub-assembly when inserting the screwdriver in the joint area.
If the cylinder head cover sub-assembly is damaged, smooth the surface with 400-grid sandpaper.
15620
16.REMOVE OIL FILTER CAP ASSEMBLY
17.SET NO. 1 CYLINDER TO TDC/COMPRESSION
| *1 | Timing Mark |
| *2 | Timing Notch |
Turn the crankshaft pulley until its timing notch and timing mark "0" of the timing chain cover are aligned.
Check that the timing marks on both the camshaft timing exhaust gear and camshaft timing gear are facing upward as shown in the illustration.
If the marks are not as shown, turn the crankshaft 1 complete revolution (360°) and align the marks as specified above.
13471
18.REMOVE CRANKSHAFT PULLEY
13540
19.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY
Remove the 2 nuts, bracket, No. 1 chain tensioner assembly and gasket.
Do not turn the crankshaft without the No. 1 chain tensioner assembly installed.
20.REMOVE ENGINE MOUNTING BRACKET STUD BOLT
Remove the engine mounting bracket stud bolt.
11302
21.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY
11302A
22.REMOVE TIMING CHAIN COVER OIL SEAL
16323
23.REMOVE WATER INLET HOUSING
Remove the 3 bolts, water inlet housing and gasket.
12511
24.REMOVE NO. 1 GENERATOR BRACKET
Remove the 4 bolts and No. 1 generator bracket.
13559
25.REMOVE CHAIN TENSIONER SLIPPER
13561
26.REMOVE NO. 1 CHAIN VIBRATION DAMPER
Remove the 2 bolts and No. 1 chain vibration damper.
13562
27.REMOVE NO. 2 CHAIN VIBRATION DAMPER
13506
28.REMOVE CHAIN SUB-ASSEMBLY
| *a | Turn |
| *b | Place the Chain on the Gear |
| *c | Loosen the Chain |
Hold the hexagonal portion of the camshaft with a wrench and turn the camshaft timing gear assembly counterclockwise to loosen the chain sub-assembly between the camshaft timing gears.
With the chain sub-assembly loosened, release the chain sub-assembly from the camshaft timing gear assembly and place it on the camshaft timing gear assembly.
Be sure to release the chain sub-assembly from the sprocket completely.
Turn the camshaft clockwise to return it to the original position and remove the chain sub-assembly.
13521
29.REMOVE CRANKSHAFT TIMING SPROCKET
13507
30.REMOVE NO. 2 CHAIN SUB-ASSEMBLY
19315
31.REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE
13521A
32.REMOVE CRANKSHAFT TIMING GEAR KEY
| *1 | Protective Tape |
Using a screwdriver, remove the 2 crankshaft timing gear keys.
Tape the screwdriver tip before use.
13050
33.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY
13070A
34.INSPECT CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY
13050
35.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY
13070A
36.REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY
37.REMOVE CAMSHAFT BEARING CAP
13511
38.REMOVE CAMSHAFT
13512
39.REMOVE NO. 2 CAMSHAFT
13801
40.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY
Remove the 16 No. 1 valve rocker arm sub-assemblies.
Arrange the removed parts in the correct order.
13750
41.REMOVE VALVE LASH ADJUSTER ASSEMBLY
Remove the 16 valve lash adjuster assemblies from the cylinder head.
Arrange the removed parts in the correct order.
15678A
42.REMOVE OIL CONTROL VALVE FILTER
Remove the oil control valve filter from the No. 1 camshaft bearing cap.
11811
43.REMOVE NO. 1 CAMSHAFT BEARING
11821
44.REMOVE NO. 2 CAMSHAFT BEARING
11103
45.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY
13716
46.REMOVE VALVE STEM CAP
Remove the 16 valve stem caps.
Arrange the removed parts in the correct order.
11114A
47.REMOVE CAMSHAFT HOUSING STRAIGHT PIN
It is not necessary to remove a straight pin unless it is being replaced.
11101
48.REMOVE CYLINDER HEAD SUB-ASSEMBLY
11115
49.REMOVE CYLINDER HEAD GASKET
12204
50.REMOVE PCV VALVE SUB-ASSEMBLY
12101A
51.REMOVE OIL PAN DRAIN PLUG
Remove the oil pan drain plug and gasket.
12102A
52.REMOVE NO. 2 OIL PAN SUB-ASSEMBLY
15100
53.REMOVE OIL PUMP ASSEMBLY
11401L
54.REMOVE ENGINE REAR OIL SEAL
11420
55.REMOVE STIFFENING CRANKCASE ASSEMBLY
Uniformly loosen and remove the 11 bolts.
| *1 | Protective Tape |
Using a screwdriver, remove the stiffening crankcase assembly by prying between the stiffening crankcase and cylinder block.
Be careful not to damage the contact surfaces of the stiffening crankcase and cylinder block.
Tape the screwdriver tip before use.
11432A
56.REMOVE NO. 1 TAPER SCREW PLUG
Remove the No. 1 taper screw plug.
57.REMOVE STUD BOLT
If a stud bolt is deformed or its threads are damaged, replace it.
58.REMOVE STIFFENING CRANKCASE RING PIN
It is not necessary to remove a ring pin unless it is being replaced.