Home › Drivetrain › K111 MULTIDRIVE / CVT › FRONT DIFFERENTIAL OIL SEAL
RM3090E _52 Drivetrain _008435 K111 MULTIDRIVE / CVT _0047071 FRONT DIFFERENTIAL OIL SEAL A

K111 MULTIDRIVE / CVT  FRONT DIFFERENTIAL OIL SEAL  REPLACEMENT  


PROCEDURE

Hide 51441 1.REMOVE NO. 1 ENGINE UNDER COVER

Hide 51443 2.REMOVE REAR ENGINE UNDER COVER RH

Hide 51444C 3.REMOVE REAR ENGINE UNDER COVER LH

Hide 4.DRAIN CONTINUOUSLY VARIABLE TRANSAXLE FLUID

a.
C242832

Using a 6 mm socket hexagon wrench, remove the overflow plug and gasket from the continuously variable transaxle assembly.


b.
C279062C06
2.583,0.823 2.833,0.396 2.833,0.396 2.948,0.396 false 2.99,0.323 3.302,0.521 0.313,0.198 10 *1
*1 No. 1 Transmission Oil Filler Tube


Using a 6 mm socket hexagon wrench, remove the No. 1 transmission oil filler tube from the continuously variable transaxle assembly and drain the continuously variable transaxle fluid.


c.

Using a 6 mm socket hexagon wrench, install the No. 1 transmission oil filler tube to the continuously variable transaxle assembly.

Torque:
1.7 N*m (17 kgf*cm, 15 in.*lbf)


d.

Temporarily install the gasket and overflow plug.

HINT:

Reuse the old gasket. The plug will be removed again to adjust the fluid level.



Hide 5.REMOVE FRONT DRIVE SHAFT ASSEMBLY LH AND RH

Hide 43457 6.REMOVE DRIVE SHAFT BEARING BRACKET

Hide 30400C 7.REMOVE CVT TYPE T OIL SEAL LH

C103977E02
0.895,2.315 1.208,2.462 0.313,0.147 10 SST 1.051,1.163 1.051,2.278 false 1.928,2.815 2.241,2.962 0.313,0.147 10 SST 2.117,2.573 2.117,2.778 false

a.

Using SST, remove the CVT type T oil seal LH from the transaxle case.

SST
09308-00010  

NOTICE:

Do not damage the transaxle case.



Hide 30400B 8.REMOVE CVT TYPE T OIL SEAL RH

C100696E02
2.753,0.392 3.091,0.554 0.337,0.162 10 SST 1.793,0.902 2.709,0.481 2.709,0.481 2.145,2.165 false

a.

Using SST, remove the CVT type T oil seal RH from the transaxle housing.

SST
09308-00010  

NOTICE:

Do not damage the transaxle housing.



Hide 30400C 9.INSTALL CVT TYPE T OIL SEAL LH

C194180E02
3.048,0.337 3.341,0.490 0.294,0.153 10 SST 1.063,2.37 1.356,2.523 0.294,0.153 10 SST 1.405,2.447 2.044,2.579 false 1.538,0.981 3.018,0.438 3.018,0.438 2.246,1.006 false

a.

Using SST and a hammer, tap in a new CVT type T oil seal LH to the transaxle case.

Standard depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:

Do not damage the lip of the CVT type T oil seal LH.


SST
09316-10010  09950-70010  (09951-07200)


b.

Coat the lip of the CVT type T oil seal LH with MP grease.


Hide 30400B 10.INSTALL CVT TYPE T OIL SEAL RH

C281505E01
0.896,2.615 1.854,2.615 false 1.906,1.271 1.396,0.323 1.396,0.323 0.792,0.323 false 1.427,1.188 1.396,0.313 false 0.583,2.542 1.042,2.74 0.458,0.198 10 false SST 0.479,0.24 0.938,0.438 0.458,0.198 10 false SST

a.

Using SST and a hammer, tap in a new CVT type T oil seal RH to the transaxle housing.

Standard depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:

Do not damage the lip of the CVT type T oil seal RH.


SST
09950-70010  09631-12090  (09951-07200, 09951-00480, 09951-00610, 09952-06010)


b.

Coat the lip of the CVT type T oil seal RH with MP grease.


Hide 43457 11.INSTALL DRIVE SHAFT BEARING BRACKET

Hide 12.INSTALL FRONT DRIVE SHAFT ASSEMBLY LH AND RH

Hide 13.ADD CONTINUOUSLY VARIABLE TRANSAXLE FLUID

Hide 51443 14.INSTALL REAR ENGINE UNDER COVER RH

Hide 51444C 15.INSTALL REAR ENGINE UNDER COVER LH

Hide 51441 16.INSTALL NO. 1 ENGINE UNDER COVER