Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY(for 2WD) › 2012.12–2015.10
RM3090E _52 Drivetrain _008761 DRIVE SHAFT / PROPELLER SHAFT _0050235 FRONT DRIVE SHAFT ASSEMBLY(for 2WD) A

DRIVE SHAFT / PROPELLER SHAFT  FRONT DRIVE SHAFT ASSEMBLY(for 2WD)  REMOVAL  


PROCEDURE

Hide 1.REMOVE FRONT WHEEL

Hide 7.DRAIN CONTINUOUSLY VARIABLE TRANSAXLE FLUID

Hide 43502H 8.REMOVE FRONT AXLE SHAFT NUT LH

Hide 43501H 9.REMOVE FRONT AXLE SHAFT NUT RH

HINT:

Use the same procedure described for the LH side.


Hide 10.DISCONNECT FRONT SPEED SENSOR LH

Hide 11.DISCONNECT FRONT SPEED SENSOR RH

HINT:

Use the same procedure described for the LH side.


Hide 48810 12.REMOVE FRONT STABILIZER LINK ASSEMBLY LH

Hide 48820B 13.REMOVE FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 48069 14.DISCONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

Hide 48068 15.DISCONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 16.DISCONNECT STEERING KNUCKLE WITH AXLE HUB LH

a.
C264664

Remove the bolt and detach the 2 guides.


b.
C129488C01
1.708,1.052 2.625,1.052 2.625,1.052 2.625,0.833 true 1.625,0.833 2.875,0.833 true 2.979,0.729 3.292,0.927 0.313,0.198 10 *a
*a Matchmark


Put matchmarks on the front drive shaft assembly LH and front axle hub sub-assembly.

NOTICE:

Do not use a punch to make the matchmarks.



c.

Using a plastic-faced hammer, disconnect the front drive shaft assembly LH from the steering knuckle with axle hub.

NOTICE:
·

Do not damage the front axle inboard joint boot and front drive shaft dust cover LH.

·

Do not excessively push out the front drive shaft assembly LH from the front axle hub.




Hide 17.DISCONNECT STEERING KNUCKLE WITH AXLE HUB RH

HINT:

Use the same procedure described for the LH side.


Hide 43420 18.REMOVE FRONT DRIVE SHAFT ASSEMBLY LH

a.
C264655N01
1.833,0.833 1.75,1.917 1.75,1.917 2.417,1.167 true 1.75,1.917 1.5,1.917 false 1.208,1.833 1.667,2.031 0.458,0.198 10 SST

Using SST, remove the front drive shaft assembly LH.

SST
09520-01010  
09520-24010  (09520-32040)

NOTICE:
·

Do not damage the transaxle oil seal, front axle inboard joint boot and front drive shaft dust cover LH.

·

Do not drop the front drive shaft assembly LH.

·

When carrying the front drive shaft assembly LH, hold it horizontally.



HINT:

Hook the SST claw at the position shown in the illustration to remove the front drive shaft assembly LH.



Hide 43410 19.REMOVE FRONT DRIVE SHAFT ASSEMBLY RH

a.

w/o Drive Shaft Bearing Case:

i.
C239399

Disconnect the drive shaft bearing bracket hole snap ring from the drive shaft bearing bracket.


ii.

Remove the bolt and front drive shaft assembly RH from the drive shaft bearing bracket.

NOTICE:
·

Do not damage the transaxle oil seal, front axle inboard joint boot, front drive shaft dust cover RH and front drive shaft dust cover.

·

Do not drop the front drive shaft assembly RH.

·

When carrying the front drive shaft assembly RH, hold it horizontally.




iii.

Remove the drive shaft bearing bracket hole snap ring from the front drive shaft assembly RH.



b.
C127638

w/ Drive Shaft Bearing Case:

i.

Remove the 2 bolts and pull out the front drive shaft assembly RH together with the drive shaft bearing case sub-assembly.


ii.

Remove the front drive shaft assembly RH from the transaxle.

NOTICE:
·

Do not damage the transaxle oil seal, front axle inboard joint boot, front drive shaft dust cover RH and front drive shaft dust cover.

·

Do not drop the front drive shaft assembly RH.

·

When carrying the front drive shaft assembly RH, hold it horizontally.





Hide 43420G 20.REMOVE FRONT DRIVE SHAFT HOLE SNAP RING LH

a.
C183640

Using a screwdriver, remove the front drive shaft hole snap ring LH.

NOTICE:

Do not damage the spline of the front drive inboard joint assembly LH.