Home › Engine / Hybrid System › 3ZR-FE ENGINE MECHANICAL › ENGINE ASSEMBLY › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _008405 3ZR-FE ENGINE MECHANICAL _0046949 ENGINE ASSEMBLY A

3ZR-FE ENGINE MECHANICAL  ENGINE ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:

As the engine assembly with transaxle is extremely heavy, the engine lifter may suddenly drop if the instructions listed in the repair manual are not followed. Therefore, always follow the instructions listed in the repair manual when performing this procedure.


NOTICE:

for Manual Transaxle:

When the transaxle is removed, be sure to use a new clutch release with bearing cylinder assembly and new installation bolts. Removal of the transaxle allows the compressed clutch release with bearing cylinder assembly to return to its original position, and dust could damage the seal of the clutch release with bearing cylinder assembly, possibly causing clutch fluid leaks.


HINT:

Perform "Inspection After Repairs" after replacing the engine assembly, cylinder head sub-assembly, camshaft, No. 2 camshaft, camshaft timing gear assembly, camshaft timing exhaust gear assembly, piston sub-assembly or piston ring.

Click hereEngine / Hybrid System>3ZR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 12372A 1.INSTALL ENGINE MOUNTING INSULATOR LH

HINT:

Perform this procedure only when replacement of the engine mounting insulator is necessary.


a.
A299349N01
1.354,0.49 1.51,0.688 0.156,0.198 10 1 2.656,0.625 2.813,0.823 0.156,0.198 10 4 2.396,1.781 2.552,1.979 0.156,0.198 10 2 1.104,1.729 1.26,1.927 0.156,0.198 10 3

Temporarily install the engine mounting insulator LH with the 4 bolts.


b.

Tighten the 4 bolts in the sequence shown in the illustration.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)


c.

Install the wire harness clamp bracket with the bolt.

Torque:
7.7 N*m (79 kgf*cm, 68 in.*lbf)


Hide 12305 2.INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

HINT:

Perform this procedure only when replacement of the engine mounting insulator is necessary.


a.
A299326N01
2.792,1.104 2.948,1.302 0.156,0.198 10 1 0.969,0.26 1.125,0.458 0.156,0.198 10 2 0.708,1.865 0.865,2.063 0.156,0.198 10 3

Temporarily install the engine mounting insulator sub-assembly RH with the 3 bolts.


b.

Tighten the 3 bolts in the sequence shown in the illustration.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)


c.

Install the radiator reservoir bracket with the bolt.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 12371A 3.INSTALL REAR ENGINE MOUNTING INSULATOR

HINT:

Perform this procedure only when replacement of the rear engine mounting insulator is necessary.


a.

Temporarily install the rear engine mounting insulator with the 2 bolts and 2 nuts.

A293519C02
0.354,0.094 0.667,0.25 0.313,0.156 10 *A 0.354,1.438 0.667,1.594 0.313,0.156 10 *B 1.188,0.188 1.5,0.344 0.313,0.156 10 *C 3.417,0.188 3.729,0.344 0.313,0.156 10 *D 1.188,1.51 1.5,1.667 0.313,0.156 10 *C 3.438,1.51 3.75,1.667 0.313,0.156 10 *D 1.542,1.031 1.698,1.229 0.156,0.198 10 1 1.531,2.333 1.688,2.531 0.156,0.198 10 1 3.958,2.344 4.115,2.542 0.156,0.198 10 1 3.958,1.021 4.115,1.219 0.156,0.198 10 1 2.896,0.969 3.052,1.167 0.156,0.198 10 2 2.896,2.26 3.052,2.458 0.156,0.198 10 2 5.323,2.271 5.479,2.469 0.156,0.198 10 2 5.323,0.969 5.479,1.167 0.156,0.198 10 2 4.99,1.167 5.146,1.365 0.156,0.198 10 3 4.99,2.469 5.146,2.667 0.156,0.198 10 3 2.563,2.458 2.719,2.656 0.156,0.198 10 3 2.563,1.146 2.719,1.344 0.156,0.198 10 3 1.948,1.167 2.104,1.365 0.156,0.198 10 4 4.385,1.188 4.542,1.385 0.156,0.198 10 4 1.958,2.5 2.115,2.698 0.156,0.198 10 4 4.385,2.5 4.542,2.698 0.156,0.198 10 4
*A for 2WD *B for 4WD / AWD
*C for Manual Transaxle *D for CVT



b.

Tighten the 2 bolts and 2 nuts in the sequence shown in the illustration.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)


Hide 43457 4.INSTALL DRIVE SHAFT BEARING BRACKET

a.

Install the drive shaft bearing bracket with the 3 bolts.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)


Hide 6.REMOVE ENGINE FROM ENGINE STAND

NOTICE:
·

Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.

·

With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine while it is suspended, as doing so is dangerous.



a.

Attach an engine sling device and hang the engine with a chain block.


b.

Lift the engine and remove it from the engine stand.


Hide 82121 8.INSTALL ENGINE WIRE

a.

Install the engine wire to the engine.


Hide 13405 9.INSTALL FLYWHEEL SUB-ASSEMBLY (for Manual Transaxle)

Hide 31400 10.INSTALL CLUTCH RELEASE WITH BEARING CYLINDER ASSEMBLY (for Manual Transaxle)

Hide 31407B 11.INSTALL CLUTCH RELEASE BLEEDER SUB-ASSEMBLY (for Manual Transaxle)

Hide 12.INSTALL CLUTCH TUBE (for Manual Transaxle)

Hide 31250 13.INSTALL CLUTCH DISC ASSEMBLY (for Manual Transaxle)

Hide 31210 14.INSTALL CLUTCH COVER ASSEMBLY (for Manual Transaxle)

Hide 31210 15.INSPECT AND ADJUST CLUTCH COVER ASSEMBLY (for Manual Transaxle)

Hide 32101 16.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for CVT)

Hide 30400 18.INSTALL CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY (for CVT)

Hide 36100 19.INSTALL TRANSFER ASSEMBLY (for 4WD/AWD)

Hide 11363A 20.INSTALL FLYWHEEL HOUSING SIDE COVER

Hide 45319A 22.INSTALL STEERING GEAR HEAT INSULATOR (for RHD)

Hide 23.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

a.

Temporarily install the front engine mounting insulator with the through bolt and nut.


b.
A300878C01
1.594,3.396 2.542,3.188 2.542,3.188 1.635,3.188 true 1.031,2.708 1.208,2.708 1.208,2.708 1.49,3.26 true 0.823,2.635 1.01,2.813 0.188,0.177 10 false *2 2.594,3.104 2.781,3.281 0.188,0.177 10 false *1
*1 Alignment Mark
*2 Protrusion


Temporarily install the front suspension crossmember with the through bolt.

HINT:

When installing the suspension crossmember, align the protrusion of the engine mounting bracket with the alignment mark of the engine mounting insulator.



c.

Place the engine on an engine lifter.

HINT:

Place the engine on wooden blocks or equivalent so that the engine is level.



d.

Operate the engine lifter and install the engine to the vehicle.

CAUTION:

Do not raise the engine more than necessary. If the engine is raised excessively, the vehicle may also be lifted up.


NOTICE:
·

Make sure that the engine is clear of all wiring and hoses.

·

While raising the engine into the vehicle, do not allow it to contact the vehicle.




e.

Temporarily install the front suspension crossmember with the 2 bolts.


f.

Temporarily install the front suspension member brace rear RH and LH with the 6 bolts.


g.

Install the engine mounting insulator LH with the through bolt and nut.

Torque:
56 N*m (571 kgf*cm, 41 ft.*lbf)

NOTICE:

While holding the bolt in place, tighten the nut.



h.
A298939N01
1.115,0.729 1.271,0.927 0.156,0.198 10 A 1.333,1.469 1.49,1.667 0.156,0.198 10 B

Install the engine mounting insulator RH with the bolt and 2 nuts.

Torque:
for bolt and nut A : 95 N*m (969 kgf*cm, 70 ft.*lbf)
for nut B : 52 N*m (530 kgf*cm, 38 ft.*lbf)


i.

Tighten the 2 front suspension crossmember sub-assembly bolts.

Torque:
137 N*m (1397 kgf*cm, 101 ft.*lbf)


j.
A297333C02
2.594,1.24 2.594,1.198 false
V100135

Bolt A
V100136

Bolt B


Tighten the 6 front suspension member brace rear bolts.

Torque:
for bolt A : 137 N*m (1397 kgf*cm, 101 ft.*lbf)
for bolt B : 93 N*m (948 kgf*cm, 69 ft.*lbf)


k.

Remove the 2 bolts and No. 1 and No. 2 engine hangers.


l.

Install the air fuel ratio sensor bracket with the bolt. Then connect the air fuel ratio sensor connector.

Torque:
39 N*m (398 kgf*cm, 29 ft.*lbf)


m.

Attach the fuel tube clamp.


n.
A297334C02
2.906,0.729 2.896,0.719 false
V100135

Bolt A
V100136

Bolt B


Install the front crossmember sub-assembly with the 6 bolts.

Torque:
for bolt A : 99 N*m (1010 kgf*cm, 73 ft.*lbf)
for bolt B : 95 N*m (969 kgf*cm, 70 ft.*lbf)


o.

Tighten the through bolt of the rear engine mounting insulator.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)

HINT:

Check that the protrusion of the engine mounting bracket is aligned with the alignment mark of the engine mounting insulator.



p.

Tighten the through bolt and nut of the front engine mounting insulator.

Torque:
145 N*m (1479 kgf*cm, 107 ft.*lbf)

NOTICE:

While holding the nut in place, tighten the through bolt.



Hide 51218A 24.INSTALL FRONT SUSPENSION MEMBER REINFORCEMENT LH

A296303

a.

Install the front suspension member reinforcement LH with the 4 bolts.

Torque:
99 N*m (1010 kgf*cm, 73 ft.*lbf)


Hide 51217A 25.INSTALL FRONT SUSPENSION MEMBER REINFORCEMENT RH

a.
A296302

Install the front suspension member reinforcement RH with the 4 bolts.

Torque:
99 N*m (1010 kgf*cm, 73 ft.*lbf)


Hide 51425B 26.INSTALL FRONT LOWER ENGINE MOUNTING BRACKET REINFORCEMENT (for 2WD)

a.
A295897

Install the front lower engine mounting bracket reinforcement with the 2 bolts.

Torque:
99 N*m (1010 kgf*cm, 73 ft.*lbf)


Hide 32101A 27.INSTALL DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT (for CVT)

Hide 37100 28.TEMPORARILY INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for 4WD/AWD)

Hide 37100 29.TIGHTEN PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for 4WD/AWD)

Hide 89465 30.CONNECT HEATED OXYGEN SENSOR (for 4WD/AWD)

Hide 17410 31.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 43420G 33.INSTALL FRONT DRIVE SHAFT HOLE SNAP RING

Hide 48069 35.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

Hide 48068 36.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 45047 37.CONNECT TIE ROD END SUB-ASSEMBLY LH

Hide 45046 38.CONNECT TIE ROD END SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 48810 39.CONNECT FRONT STABILIZER LINK ASSEMBLY LH

Hide 48820B 40.CONNECT FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 41.CONNECT FRONT SPEED SENSOR LH

Hide 42.CONNECT FRONT SPEED SENSOR RH

HINT:

Use the same procedure described for the LH side.


Hide 43502H 43.INSTALL FRONT AXLE SHAFT NUT LH

Hide 43501H 44.INSTALL FRONT AXLE SHAFT NUT RH

HINT:

Use the same procedure described for the LH side.


Hide 45025D 45.CONNECT NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

Hide 45260 46.CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 45259A 47.INSTALL COLUMN HOLE COVER SILENCER SHEET

Hide 48.CONNECT CLUTCH HOSE (for Manual Transaxle)

a.

Connect the clutch hose and install a new clip to the clutch hose.

NOTICE:

Install the clip as far as it will go.



b.

Using a 10 mm union nut wrench, connect the clutch hose to the accumulator to flexible hose tube while holding the flexible hose.

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)

NOTICE:
·

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Do not kink or damage the clutch release cylinder tube.

·

Do not allow any foreign matter such as dirt or dust to enter the clutch release cylinder tube from the clip or bracket.

·

This torque value is effective when the union nut wrench is parallel to the torque wrench.




Hide 49.CONNECT TRANSAXLE CONTROL CABLE ASSEMBLY (for CVT)

a.

Connect the clamp of the transaxle control cable assembly with the bolt.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


b.

Connect the transaxle control cable assembly to the control cable support.


c.

Connect the transaxle control cable assembly to the bracket with a new clip.


d.

Connect the transaxle control cable assembly to the control shaft lever with the nut.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 33820B 50.CONNECT TRANSAXLE CONTROL CABLE ASSEMBLY (for Manual Transaxle)

a.

Connect the transaxle control cable assembly to the control cable bracket and install 2 new clips.


b.

Connect the transaxle control cable assembly to the transaxle and install the 2 clips.


Hide 51.CONNECT WIRE HARNESS AND HOSE

a.

Connect the heater water outlet hose and heater water inlet hose to the heater core and slide the 2 clamps to secure the hoses.


b.

Connect the connector tube hose to the air tube and slide the clamp to secure it.


c.

for Manual Transaxle:

Attach the clamp and connect the engine wire to the manual transaxle with the bolt.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


d.

for CVT:

Attach the clamp and connect the engine wire to the CVT with the bolt.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


e.

Attach the wire harness clamp.


f.

Connect the starter wire with the nut, and then connect the terminal cap.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


g.

Attach the 2 claws to install the wire harness to the engine room No. 1 junction block.


h.

Connect the 2 wire harness connectors to the engine room No. 1 junction block and install the nut.

Torque:
12.8 N*m (131 kgf*cm, 9 ft.*lbf)


i.

Attach the 2 clamps and install the bolt.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


Hide 23901 52.CONNECT FUEL TUBE SUB-ASSEMBLY

a.

Connect the fuel tube sub-assembly and then install the No. 1 fuel pipe clamp.

Click hereEngine / Hybrid System>3ZR-FE FUEL>FUEL SYSTEM>PRECAUTION


Hide 16571 53.CONNECT NO. 1 RADIATOR HOSE

a.

for CVT:

Connect the breather plug hose to the clamp.


b.

Connect the No. 1 radiator hose to the cylinder head and slide the clamp to secure it.


Hide 74414B 55.INSTALL BATTERY BRACKET REINFORCEMENT

Hide 74411B 56.INSTALL FRONT BATTERY BRACKET

Hide 16057 57.CONNECT RADIATOR HOSE SUB-ASSEMBLY

Hide 74431 58.INSTALL BATTERY TRAY

Hide 28800 59.INSTALL BATTERY

Hide 74404A 60.INSTALL BATTERY CLAMP SUB-ASSEMBLY

Hide 61.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

Hide 17705 62.INSTALL AIR CLEANER CAP SUB-ASSEMBLY

Hide 88310 63.CONNECT COMPRESSOR WITH PULLEY ASSEMBLY

a.

Using an E8 "TORX" socket wrench, connect the compressor with pulley assembly with the 2 stud bolts.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


b.
A298965N01
0.604,1.833 0.76,2.031 0.156,0.198 10 1 2.302,1.083 2.458,1.281 0.156,0.198 10 2 0.833,0.156 0.99,0.354 0.156,0.198 10 4 2.333,1.646 2.49,1.844 0.156,0.198 10 3

Install the 2 bolts and 2 nuts.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

HINT:

Tighten the bolts and nuts in the order shown in the illustration.



c.

Connect the connector.


Hide 16572D 64.CONNECT NO. 2 RADIATOR HOSE

a.

Connect the No. 2 radiator hose to the water inlet and slide the clamp to secure it.


Hide 16470 68.CONNECT RADIATOR RESERVOIR ASSEMBLY

a.

Connect the radiator reservoir assembly with the 2 bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


b.

Connect the No. 1 and No. 2 water by-pass hoses to the radiator reservoir assembly and slide the 2 clamps to secure the hoses.


Hide 69.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 73.ADD TRANSFER OIL (for 4WD / AWD)

Hide 75.INSPECT SHIFT LEVER POSITION (for CVT)

Hide 51443 85.INSTALL REAR ENGINE UNDER COVER RH

a.

Install the rear engine under cover RH with the 3 clips.


Hide 51444 86.INSTALL REAR ENGINE UNDER COVER LH

a.

Install the rear engine under cover LH with the 3 clips.


Hide 51441 87.INSTALL NO. 1 ENGINE UNDER COVER

Hide 11212 88.INSTALL NO. 2 CYLINDER HEAD COVER