Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING ASSIST MONITOR SYSTEM › 2012.12–2013.11
RM3090E _56 Audio / Visual / Telematics _008432 PARK ASSIST / MONITORING _0047059 PARKING ASSIST MONITOR SYSTEM Y

PARK ASSIST / MONITORING  PARKING ASSIST MONITOR SYSTEM  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

·

Use the following procedure to troubleshoot the parking assist monitor system.

·

*: Use the GTS.


PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.INSPECT BATTERY VOLTAGE
2.INSPECT BATTERY VOLTAGE
a.

Measure the battery voltage with the ignition switch off.

Standard voltage:

11 to 14 V


If the voltage is below 11 V, replace or recharge the battery before proceeding to the next step.


Result:
Proceed to
NEXT



NEXT

3.CHECK IF SAME SYMPTOM APPEARS IN OTHER SYSTEM
3.CHECK IF SAME SYMPTOM APPEARS IN OTHER SYSTEM

Result:
Proceed to
Navigation system is normal
Navigation system is abnormal



Navigation system is normal

4.CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*

Navigation system is abnormal

4.CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*
a.

Use the GTS to check if the CAN communication system is functioning normally.

for LHD (Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD)>HOW TO PROCEED WITH TROUBLESHOOTING)

for RHD (Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD)>HOW TO PROCEED WITH TROUBLESHOOTING)

Result:
Proceed to
CAN DTCs are not output. (w/ Power Back Door System)
CAN DTCs are not output. (w/o Power Back Door System)
CAN DTCs are output. (for LHD)
CAN DTCs are output. (for RHD)




CAN DTCs are not output. (w/ Power Back Door System)

5.CHECK FOR DTC (BACK DOOR CLOSER SYSTEM)*

CAN DTCs are not output. (w/o Power Back Door System)

6.CHECK FOR DTC (PARKING ASSIST MONITOR SYSTEM)*

CAN DTCs are output. (for LHD)

CAN DTCs are output. (for RHD)

5.CHECK FOR DTC (BACK DOOR CLOSER SYSTEM)*

Result:
Proceed to
Back door closer system DTCs are not output.
Back door closer system DTCs are output.



Back door closer system DTCs are not output.

6.CHECK FOR DTC (PARKING ASSIST MONITOR SYSTEM)*

Back door closer system DTCs are output.

6.CHECK FOR DTC (PARKING ASSIST MONITOR SYSTEM)*


c.

Recheck for DTCs. Try to prompt the DTC by simulating the original activity that the DTC suggests.

NOTICE:

The navigation ECU sub-assembly outputs DTCs for the following systems. When DTCs other than those in Diagnostic Trouble Code Chart for the parking assist monitor system are output, refer to Diagnostic Trouble Code Chart for the relevant systems.



Result:
Proceed to
No DTCs are output.
DTCs for parking assist monitor system are output.
DTCs for navigation system are output.



No DTCs are output.

7.PERFORM SYMPTOMS TABLE

DTCs for parking assist monitor system are output.

9.ADJUST, REPAIR OR REPLACE

DTCs for navigation system are output.

7.PERFORM SYMPTOMS TABLE

Result:
Proceed to
Fault is not listed in Problem Symptoms Table
Fault is listed in Problem Symptoms Table



Fault is not listed in Problem Symptoms Table

8.OVERALL ANALYSIS AND TROUBLESHOOTING*

Fault is listed in Problem Symptoms Table

9.ADJUST, REPAIR OR REPLACE
9.ADJUST, REPAIR OR REPLACE
Result:
Proceed to
NEXT



NEXT

10.CONFIRMATION TEST
10.CONFIRMATION TEST
Result:
Proceed to
NEXT



NEXT

END