Home › Vehicle Exterior › LIGHTING (EXT) › AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM
RM3090E _59 Vehicle Exterior _008430 LIGHTING (EXT) _0047056 AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM J

LIGHTING (EXT)  AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM  Headlight Leveling ECU Power Source Circuit  


DESCRIPTION

This circuit detects the state of the ignition switch, and sends it to the headlight leveling ECU.

WIRING DIAGRAM

E227418E04
5.104,2.76 6.625,3.104 1.521,0.344 10 Headlight Leveling ECU Assembly 5.104,2.594 5.51,2.781 0.406,0.188 10 A67 0.594,1.094 2.021,1.281 1.427,0.188 10 from IG1 NO.1 Relay 5.469,1.063 5.667,1.26 0.198,0.198 10 IG 5.458,2.156 5.656,2.354 0.198,0.198 10 E1 5.271,2.063 5.375,2.208 0.104,0.146 10 9 5.25,0.958 5.375,1.135 0.125,0.177 10 1 3.354,1.26 4.448,1.417 1.094,0.156 10 ECU-IG NO.1

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

After replacing the headlight leveling ECU, initialization of the ECU is necessary.

Click hereVehicle Exterior>LIGHTING (EXT)>AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM>INITIALIZATION


PROCEDURE

1.READ VALUE USING GTS (IGNITION POWER SUPPLY)
a.

Using the GTS, read the Data List.

Click hereVehicle Exterior>LIGHTING (EXT)>AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > HL AutoLeveling > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
+B Ignition power supply voltage value 0 to 19.75 V 11 to 14 V -
Body Electrical > HL AutoLeveling > Data List
Tester Display
+B
50003 165 7
OK:

The display is as specified in the normal condition column.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING ECU ASSEMBLY - BATTERY AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING ECU ASSEMBLY - BATTERY AND BODY GROUND)
a.
E136327C01
0.063,0.542 0.5,0.833 0.438,0.292 0.677,1.323 0.406,1.823 false 2.792,1.292 3.042,1.854 false 0.135,0.042 0.438,0.271 0.302,0.229 10 *a 0.167,0.625 0.542,0.792 0.375,0.167 10 A67 3.042,1.854 3.271,2.021 0.229,0.167 10 E1 0.271,1.854 0.5,2.021 0.229,0.167 10 IG
*a Front view of wire harness connector
(to Headlight Leveling ECU Assembly)


Disconnect the headlight leveling ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A67-1 (IG) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A67-9 (E1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT LEVELING ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR