Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD) › 2012.12–2015.10
RM3090E _57 Power Source / Network _008434 NETWORKING _0048454 CAN COMMUNICATION SYSTEM(for LHD) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD)  Skid Control ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area

*: w/ Stop and Start System

Skid Control ECU Communication Stop Mode Either condition is met:
·

"Skid Control (ABS/VSC/TRAC)" is not displayed on "CAN Bus Check".

(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Skid Control ECU Communication Stop Mode" in "DTC Combination Table".

(Click here)


·

Power source or inside brake actuator assembly (skid control ECU)

·

Brake actuator assembly (skid control ECU) CAN branch wire or connector

·

Brake actuator assembly (skid control ECU)

·

Engine stop and start ECU*



WIRING DIAGRAM

B338293E01
5.177,6 6.823,6.323 1.646,0.323 10 A64 0.385,4.5 2.115,4.667 1.729,0.167 10 G87 5.51,5.208 6.25,5.375 0.74,0.167 10 GND2 5.531,4.729 6.271,4.896 0.74,0.167 10 GND1 5.271,5.052 6.01,5.219 0.74,0.167 10 13 5.323,4.594 6.063,4.76 0.74,0.167 10 1 5.177,6.146 6.823,6.469 1.646,0.323 10 Brake Actuator Assembly (Skid Control ECU) 0.375,4.656 1.75,4.979 1.375,0.323 10 Engine Stop and Start ECU*2 1.073,3.854 2.802,4.021 1.729,0.167 10 IGO1 5.552,2.938 5.938,3.104 0.385,0.167 10 IG1 5.292,2.813 6.031,2.979 0.74,0.167 10 34 5.281,2.313 6.021,2.479 0.74,0.167 10 24 5.271,1.833 6.01,2 0.74,0.167 10 12 5.521,2.438 5.906,2.604 0.385,0.167 10 BM 5.521,1.99 5.906,2.156 0.385,0.167 10 +BS 3.719,2.75 4.781,3.052 1.063,0.302 10 ECU-IG NO.3 3.844,2.26 4.802,2.542 0.958,0.281 10 ABS NO.1 3.844,1.771 4.708,2.021 0.865,0.25 10 ABS NO.2 2.063,1.948 2.885,2.146 0.823,0.198 10 from Battery 2.063,2.406 2.896,2.615 0.833,0.208 10 from Battery 1.531,2.917 2.885,3.135 1.354,0.219 10 from IG1 NO.2 Relay 1.5,3.74 3.229,3.906 1.729,0.167 10 12 0.271,6.01 2.302,6.198 2.031,0.188 10 *1: w/o Stop and Start System 3.302,2.802 3.49,2.99 0.188,0.188 10 *1 0.281,6.354 2.313,6.542 2.031,0.188 10 *2: w/ Stop and Start System 5.552,0.833 6.292,1 0.74,0.167 10 CANH 5.542,1.24 6.281,1.406 0.74,0.167 10 CANL 5.26,1.156 6,1.323 0.74,0.167 10 14 5.271,0.74 6.01,0.906 0.74,0.167 10 25 1.531,0.75 2.271,0.917 0.74,0.167 10 1 1.542,1.177 2.281,1.344 0.74,0.167 10 2 0.115,1.625 2.021,1.781 1.906,0.156 10 G120 0.115,1.792 2.021,1.948 1.906,0.156 10 No. 1 CAN Junction Connector 0.115,0.083 2.74,0.26 2.625,0.177 12 w/ Vehicle Stability Control System: 3.313,3.75 3.5,3.938 0.188,0.188 10 *2

B338294E01
5.219,5.042 6.813,5.354 1.594,0.313 10 A63 0.094,0.094 5.75,0.292 5.656,0.198 12 w/o Vehicle Stability Control System: 5.219,5.188 6.813,5.531 1.594,0.344 10 Brake Actuator Assembly (Skid Control ECU) 5.563,4.208 6.688,4.385 1.125,0.177 10 GND2 5.573,3.729 6.698,3.906 1.125,0.177 10 GND1 5.583,3.042 6.708,3.219 1.125,0.177 10 IG1 5.573,2.552 6.698,2.729 1.125,0.177 10 +BM 5.583,2.094 6.708,2.271 1.125,0.177 10 +BS 3.917,1.927 4.677,2.177 0.76,0.25 10 ABS NO.2 3.906,2.385 4.667,2.615 0.76,0.229 10 ABS NO.1 3.802,2.896 4.771,3.188 0.969,0.292 10 ECU-IG NO.3 2.094,2.083 2.865,2.26 0.771,0.177 10 from Battery 2.104,2.542 2.875,2.719 0.771,0.177 10 from Battery 1.583,3.042 2.865,3.24 1.281,0.198 10 from IG1 NO.2 Relay 5.302,4.083 6.427,4.26 1.125,0.177 10 13 5.406,3.594 6.531,3.771 1.125,0.177 10 1 5.344,2.938 6.469,3.115 1.125,0.177 10 34 5.344,2.438 6.469,2.615 1.125,0.177 10 24 5.344,1.969 6.469,2.146 1.125,0.177 10 12 5.323,0.854 6.448,1.031 1.125,0.177 10 25 5.333,1.26 6.458,1.438 1.125,0.177 10 14 5.583,0.969 6.708,1.146 1.125,0.177 10 CANH 5.583,1.396 6.708,1.573 1.125,0.177 10 CANL 1.563,1.292 2.688,1.469 1.125,0.177 10 2 1.563,0.865 2.688,1.042 1.125,0.177 10 1 0.156,1.75 2.042,1.906 1.885,0.156 10 G120 0.167,1.917 2.052,2.073 1.885,0.156 10 No. 1 CAN Junction Connector

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

DTC check procedure: Turn the ignition switch to ON and wait at least 60 seconds.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (SKID CONTROL ECU CAN BRANCH WIRE)
a.
C234968C24
0.938,0.198 1.396,0.469 0.458,0.271 1.875,0.188 2.333,0.458 0.458,0.271 0.479,0.74 0.677,0.74 0.677,0.74 1.458,1.281 true 0.885,1.927 1.115,1.927 1.115,1.927 1.458,1.365 true 1.969,0.25 2.323,0.458 0.354,0.208 10 A63 0.083,0.073 0.344,0.229 0.26,0.156 10 *a 0.479,1.844 0.885,2.01 0.406,0.167 10 CANH 0.063,0.667 0.469,0.833 0.406,0.167 10 CANL 1.479,0.271 1.792,0.427 0.313,0.156 10 *A 2.438,0.26 2.75,0.417 0.313,0.156 10 *B 1.031,0.26 1.438,0.469 0.406,0.208 10 A64
*A w/ Vehicle Stability Control System
*B w/o Vehicle Stability Control System
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the brake actuator assembly (skid control ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Vehicle Stability Control System
Tester Connection Condition Specified Condition
A64-25 (CANH) - A64-14 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω

w/o Vehicle Stability Control System
Tester Connection Condition Specified Condition
A63-25 (CANH) - A63-14 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE SKID CONTROL ECU CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

2.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BATTERY AND BODY GROUND)
a.
C234968C25
0.865,0.115 1.344,0.448 0.479,0.333 1.688,0.115 2.167,0.448 0.479,0.333 2.01,1.99 2.24,1.99 2.24,1.99 2.448,1.354 true 0.573,0.563 0.813,0.563 0.813,0.563 1.167,1.021 true 2.813,0.385 2.583,0.385 2.583,0.385 2.458,1.021 true 0.583,1.885 0.875,1.885 0.875,1.885 1.167,1.323 true 0.969,0.208 1.302,0.438 0.333,0.229 10 A64 0.083,0.073 0.344,0.229 0.26,0.156 10 *a 1.083,1.917 2.01,2.083 0.927,0.167 10 BM*A, +BM*B 0.177,0.5 0.583,0.667 0.406,0.167 10 GND1 0.167,1.813 0.573,1.979 0.406,0.167 10 GND2 2.865,0.323 3.271,0.49 0.406,0.167 10 +BS 1.417,0.198 1.75,0.427 0.333,0.229 10 *A 1.802,0.198 2.135,0.427 0.333,0.229 10 A63 2.25,0.198 2.583,0.427 0.333,0.229 10 *B
*A w/ Vehicle Stability Control System
*B w/o Vehicle Stability Control System
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])


Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
w/ Vehicle Stability Control System
Tester Connection Condition Specified Condition
A64-12 (+BS) - Body ground Always 11 to 14 V
A64-24 (BM) - Body ground Always 11 to 14 V

w/o Vehicle Stability Control System
Tester Connection Condition Specified Condition
A63-12 (+BS) - Body ground Always 11 to 14 V
A63-24 (+BM) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Vehicle Stability Control System
Tester Connection Condition Specified Condition
A64-1 (GND1) - Body ground Always Below 1 Ω
A64-13 (GND2) - Body ground Always Below 1 Ω


w/o Vehicle Stability Control System
Tester Connection Condition Specified Condition
A63-1 (GND1) - Body ground Always Below 1 Ω
A63-13 (GND2) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BATTERY)
a.
C234968C26
0.781,0.125 1.281,0.438 0.5,0.313 1.906,0.115 2.406,0.427 0.5,0.313 1.677,1.969 1.906,1.969 1.906,1.969 2.208,1.365 true 0.906,0.208 1.25,0.396 0.344,0.188 10 A64 0.083,0.073 0.344,0.229 0.26,0.156 10 *a 1.417,1.896 2,2.073 0.583,0.177 10 IG1 1.365,0.198 1.708,0.385 0.344,0.188 10 *A 2,0.188 2.344,0.375 0.344,0.188 10 A63 2.458,0.188 2.802,0.375 0.344,0.188 10 *B
*A w/ Vehicle Stability Control System
*B w/o Vehicle Stability Control System
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
w/ Vehicle Stability Control System
Tester Connection Switch Condition Specified Condition
A64-34 (IG1) - Body ground Ignition switch ON 11 to 14 V

w/o Vehicle Stability Control System
Tester Connection Switch Condition Specified Condition
A63-34 (IG1) - Body ground Ignition switch ON 11 to 14 V



Result:
Result Proceed to
OK A
NG (w/o Vehicle Stability Control System) B
NG (w/ Vehicle Stability Control System and w/o Stop and Start System)
NG (w/ Vehicle Stability Control System and w/ Stop and Start System) C



A

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)

B

REPAIR OR REPLACE HARNESS OR CONNECTOR

C

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - ENGINE STOP AND START ECU)
4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - ENGINE STOP AND START ECU)
a.

Disconnect the G87 engine stop and start ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A64-34 (IG1) - G87-12 (IGO1) Always Below 1 Ω
A64-34 (IG1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR