Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD) › 2012.12–2015.10
RM3090E _57 Power Source / Network _008434 NETWORKING _0048454 CAN COMMUNICATION SYSTEM(for LHD) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD)  Combination Meter ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area

*: w/ Stop and Start System

Combination Meter ECU Communication Stop Mode Either condition is met:
·

"Combination Meter" is not displayed on "CAN Bus Check".

(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Combination Meter ECU Communication Stop Mode" in "DTC Combination Table".

(Click here)


·

Power source or inside combination meter assembly

·

Combination meter assembly CAN main wire or connector

·

Combination meter assembly

·

Engine stop and start ECU*



WIRING DIAGRAM

C277453E01
5.333,5.417 6.5,5.771 1.167,0.354 10 21 5.25,6.323 7.063,6.5 1.813,0.177 10 Combination Meter Assembly 5.25,6.167 6.417,6.521 1.167,0.354 10 G16 5.615,5.563 6.781,5.917 1.167,0.354 10 ET 5.333,4.583 6.5,4.938 1.167,0.354 10 40 5.333,3.729 6.5,4.083 1.167,0.354 10 39 5.615,3.896 6.781,4.25 1.167,0.354 10 IG+ 5.615,4.729 6.781,5.083 1.167,0.354 10 B 2.25,4.729 3.417,5.083 1.167,0.354 10 from Battery 2.063,3.875 3.229,4.229 1.167,0.354 10 from IG2 Relay 3.906,4.531 5.073,4.885 1.167,0.354 10 ECU-B NO.2 4.052,3.708 4.667,3.896 0.615,0.188 10 METER 4.833,3.75 5.448,3.938 0.615,0.188 10 *2 4.833,2.917 5.448,3.104 0.615,0.188 10 *1 1.5,2.896 2.115,3.083 0.615,0.188 10 11 1,3.031 1.615,3.219 0.615,0.188 10 IGO2 0.333,3.563 0.948,3.75 0.615,0.188 10 G87 0.333,3.76 1.74,4.083 1.406,0.323 10 Engine Stop and Start ECU*1 0.396,5.896 2.333,6.083 1.938,0.188 10 *1: w/ Stop and Start System 0.396,6.313 2.333,6.5 1.938,0.188 10 *2: w/o Stop and Start System 1.469,0.813 2.083,1 0.615,0.188 10 1 1.5,1.313 2.115,1.5 0.615,0.188 10 2 0.333,1.813 0.948,2 0.615,0.188 10 G128 0.344,2 3.417,2.25 3.073,0.25 10 No. 2 CAN Junction Connector 5.333,0.771 6.5,1.125 1.167,0.354 10 32 5.333,1.313 6.5,1.667 1.167,0.354 10 31 5.615,1.583 6.781,1.938 1.167,0.354 10 CANL 5.615,0.802 6.781,1.156 1.167,0.354 10 CANH

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

DTC check procedure: Turn the ignition switch to ON and wait at least 51 seconds.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (COMBINATION METER ASSEMBLY CAN MAIN WIRE)
a.
C221258C08
1.521,0.333 1.927,0.615 0.406,0.281 1.25,2 1.521,2 1.521,2 1.677,1.323 true 1.052,1.781 1.292,1.781 1.292,1.781 1.615,1.302 true 0.073,0.052 0.24,0.24 0.167,0.188 10 *a 0.635,1.688 1.063,1.844 0.427,0.156 10 CANH 0.875,1.906 1.271,2.063 0.396,0.156 10 CANL 1.583,0.375 1.906,0.563 0.323,0.188 10 G16
*a Rear view of wire harness connector
(to Combination Meter Assembly)


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G16-32 (CANH) - G16-31 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE COMBINATION METER ASSEMBLY CAN MAIN WIRE OR CONNECTOR (CANH, CANL)

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BATTERY AND BODY GROUND)
a.
C221258C06
1.479,0.313 1.906,0.563 0.427,0.25 2.469,1.344 2.646,1.51 2.646,1.51 2.833,1.51 true 0.635,1.563 0.865,1.563 0.865,1.563 1.01,1.344 true 0.156,0.083 0.469,0.24 0.313,0.156 10 *a 1.552,0.365 1.833,0.573 0.281,0.208 10 G16 0.49,1.5 0.646,1.698 0.156,0.198 10 B 2.875,1.427 3.219,1.604 0.344,0.177 10 ET
*a Rear view of wire harness connector
(to Combination Meter Assembly)


Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G16-40 (B) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E16-21 (ET) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BATTERY)
a.
C221258C07
1.479,0.313 1.906,0.563 0.427,0.25 0.719,1.656 0.906,1.656 0.906,1.656 1.073,1.344 true 0.156,0.083 0.469,0.24 0.313,0.156 10 *a 1.552,0.365 1.833,0.573 0.281,0.208 10 G16 0.448,1.573 0.75,1.74 0.302,0.167 10 IG+
*a Rear view of wire harness connector
(to Combination Meter Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G16-39 (IG+) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG (w/o Stop and Start System)
NG (w/ Stop and Start System)



OK

REPLACE COMBINATION METER ASSEMBLY

NG (w/o Stop and Start System)

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG (w/ Stop and Start System)

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ENGINE STOP AND START ECU)
4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ENGINE STOP AND START ECU)
a.

Disconnect the G87 engine stop and start ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G16-39 (IG+) - G87-11 (IGO2) Always Below 1 Ω
G16-39 (IG+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR