Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2012.12–2015.04
RM3090E _54 Brake _008767 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0048751 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  TC and CG Terminal Circuit  


DESCRIPTION

Connecting terminals TC and CG of the DLC3 causes the ECU to display the DTC by blinking the ABS warning light and slip indicator light.

WIRING DIAGRAM

C243297E09
0.5,2.177 0.948,2.417 0.448,0.24 10 ECM 0.5,2.021 1.479,2.281 0.979,0.26 10 A61*1, A62*2 1.094,1.542 1.323,1.698 0.229,0.156 10 TC 1.396,1.26 1.792,1.5 0.396,0.24 10 26*1 5.333,1.49 6.865,1.979 1.531,0.49 10 Skid Control ECU (Brake Actuator Assembly) 5.396,2.563 5.583,2.708 0.188,0.146 10 13 5.458,2.948 5.552,3.083 0.094,0.135 10 4 5.646,2.656 5.854,2.802 0.208,0.146 10 TC 5.656,3.031 5.885,3.177 0.229,0.146 10 CG 5.594,3.583 5.958,3.802 0.365,0.219 10 G14 5.594,3.74 6.104,3.979 0.51,0.24 10 DLC3 1.198,4.365 2.865,4.521 1.667,0.156 10 : CAN Communication Line 1.396,1.427 2.021,1.719 0.625,0.292 10 23*2 0.271,3.24 2.396,3.51 2.125,0.271 10 *1: 1AD-FTV, 2AD-FTV, 2AD-FHV 0.292,3.573 2.271,3.823 1.979,0.25 10 *2: 2AR-FE, 3ZR-FE, 3ZR-FAE

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM

Result:
Proceed to
DTC is not output
DTC is output (for LHD)
DTC is output (for RHD)



DTC is not output

2.INSPECT DLC3

DTC is output (for LHD)

DTC is output (for RHD)

2.INSPECT DLC3
a.
C146309C94
0.104,1.375 0.5,1.635 0.396,0.26 1.656,0.802 1.969,0.302 1.969,0.302 2.094,0.302 false 1.875,1.469 1.563,2.021 1.563,2.021 1.438,2.021 false 0.125,0.083 0.427,0.229 0.302,0.146 10 *a 2.156,0.208 2.458,0.354 0.302,0.146 10 CG 1.177,1.948 1.479,2.094 0.302,0.146 10 TC 0.177,1.427 0.51,1.635 0.333,0.208 10 G14
*a DLC3


Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G14-13 (TC) - G14-4 (CG) Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG




OK

5.INSPECT ECM (TC of DLC3 INPUT)

NG

3.CHECK HARNESS AND CONNECTOR (TC of DLC3 - ECM)
3.CHECK HARNESS AND CONNECTOR (TC of DLC3 - ECM)
a.

Turn the ignition switch off.


b.

for 1AD-FTV, 2AD-FTV, 2AD-FHV:

Disconnect the A61 ECM connector.


c.

for 2AR-FE, 3ZR-FE, 3ZR-FAE:

Disconnect the A62 ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1AD-FTV, 2AD-FTV, 2AD-FHV:
Tester Connection Condition Specified Condition
G14-13 (TC) - A61-26 (TC) Always Below 1 Ω
G14-13 (TC) - Body ground Always 10 kΩ or higher


Standard Resistance:
for 2AR-FE, 3ZR-FE, 3ZR-FAE:
Tester Connection Condition Specified Condition
G14-13 (TC) - A62-23 (TC) Always Below 1 Ω
G14-13 (TC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)
a.

for 1AD-FTV, 2AD-FTV, 2AD-FHV:

Reconnect the A61 ECM connector.


b.

for 2AR-FE, 3ZR-FE, 3ZR-FAE:

Reconnect the A62 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G14-4 (CG) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.INSPECT ECM (TC of DLC3 INPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT ECM (TC of DLC3 INPUT)
a.
C146309C94
0.104,1.375 0.5,1.635 0.396,0.26 1.656,0.802 1.969,0.302 1.969,0.302 2.094,0.302 false 1.875,1.469 1.563,2.021 1.563,2.021 1.438,2.021 false 0.125,0.083 0.427,0.229 0.302,0.146 10 *a 2.156,0.208 2.458,0.354 0.302,0.146 10 CG 1.177,1.948 1.479,2.094 0.302,0.146 10 TC 0.177,1.427 0.51,1.635 0.333,0.208 10 G14
*a DLC3


Turn the ignition switch off.


b.

Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.


SST
09843-18040  

c.

Turn the ignition switch to ON.


d.

Check that the malfunction indicator lamp is blinking.


Result:
Proceed to
Malfunction indicator lamp is blinking (for 1AD-FTV)
Malfunction indicator lamp is blinking (for 2AD-FHV)
Malfunction indicator lamp is blinking (for 2AD-FTV)
Malfunction indicator lamp is blinking (for 2AR-FE)
Malfunction indicator lamp is blinking (for 3ZR-FAE)
Malfunction indicator lamp is blinking (for 3ZR-FE)
Malfunction indicator lamp is not blinking



Malfunction indicator lamp is blinking (for 1AD-FTV)

Malfunction indicator lamp is blinking (for 2AD-FHV)

Malfunction indicator lamp is blinking (for 2AD-FTV)

Malfunction indicator lamp is blinking (for 2AR-FE)

Malfunction indicator lamp is blinking (for 3ZR-FAE)

Malfunction indicator lamp is blinking (for 3ZR-FE)

Malfunction indicator lamp is not blinking