Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2012.12–2015.10
RM3090E _54 Brake _008767 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0048751 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1203  ECM Communication Circuit Malfunction  


DESCRIPTION

The circuit is used to send TRC/TRAC and VSC control information from the skid control ECU (brake actuator assembly) to the ECM, and engine control information from the ECM to the skid control ECU (brake actuator assembly) through the CAN communication system.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1203 ECM Communication Circuit Malfunction Engine, drive source and destination variations that are sent from the ECM do not match the ones of the skid control ECU (brake actuator assembly).
·

ECM

·

Skid control ECU (Brake actuator assembly)



PROCEDURE

1.CHECK PART NUMBER (ECM AND BRAKE ACTUATOR ASSEMBLY)
a.

Check that the proper ECM is installed.


Result:
Proceed to
Proper ECM is installed
Proper ECM are not installed (for 1AD-FTV)
Proper ECM are not installed (for 2AD-FHV)
Proper ECM are not installed (for 2AD-FTV)
Proper ECM are not installed (for 2AR-FE)
Proper ECM are not installed (for 3ZR-FAE)
Proper ECM are not installed (for 3ZR-FE)



Proper ECM is installed

2.CHECK BRAKE ACTUATOR ASSEMBLY

Proper ECM are not installed (for 1AD-FTV)

Proper ECM are not installed (for 2AD-FHV)

Proper ECM are not installed (for 2AD-FTV)

Proper ECM are not installed (for 2AR-FE)

Proper ECM are not installed (for 3ZR-FAE)

Proper ECM are not installed (for 3ZR-FE)

2.CHECK BRAKE ACTUATOR ASSEMBLY
a.

Check if the brake actuator assembly had been replaced before the DTC was recorded.


Result:
Proceed to
The brake actuator assembly is not replaced
The brake actuator assembly is replaced



The brake actuator assembly is not replaced

3.RECONFIRM DTC

The brake actuator assembly is replaced

4.PERFORM INITIALIZATION AND CALIBRATION
3.RECONFIRM DTC
a.

Clear the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Check if the same DTC is recorded.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Proceed to
DTC C1203 is not output
DTC C1203 is output



DTC C1203 is not output

DTC C1203 is output

4.PERFORM INITIALIZATION AND CALIBRATION

Result:
Proceed to
NEXT



NEXT

5.RECONFIRM DTC
5.RECONFIRM DTC
a.

Clear the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Check if the same DTC is recorded.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Proceed to
DTC C1203 is not output
DTC C1203 is output



DTC C1203 is not output

END

DTC C1203 is output