Refer to DTCs C1281, C1421, C1423 and C1424.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1281
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1422 | Master Cylinder Pressure Sensor Zero Point High Malfunction | When the stop light switch is OFF, the PMC terminal voltage is more than 0.86 V for 5 seconds or more while the vehicle is being driven at a speed of 3 km/h (2 mph) or more. | ·
STOP fuse ·
Stop light switch assembly ·
Stop light switch circuit ·
Skid control ECU (Brake actuator assembly) ·
Brake actuator assembly (Master cylinder pressure sensor) |
Refer to DTC C1425.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1425
When replacing the skid control ECU (brake actuator assembly), perform zero point calibration.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Check the DTC C1380 (w/ Stop Light control Relay) or C1425 is output.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC C1380 (w/ Stop Light control Relay) or C1425 is not output | A |
| DTCs C1422 and C1380 are output (w/ Stop Light control Relay) | B |
| DTCs C1422 and C1425 are output | C |
A
B
C
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
In accordance with the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Stop Light SW | Stop light switch assembly | OFF or ON | OFF: Brake pedal released
ON: Brake pedal depressed |
- |
| Master Cylinder Sensor | Master cylinder pressure sensor reading | Min.: 0 V, Max.: 5 V | Brake pedal released: 0.3 to 0.9 V | Reading increases when brake pedal is depressed. |
| Tester Display |
|---|
| Stop Light SW |
| Master Cylinder Sensor |
Master cylinder pressure sensor reading is 0.86 V or less at the instant the stop light switch changes from off to on.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Clear the DTCs.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more and perform braking test (decelerate the vehicle by depressing the brake pedal).
Check if the same DTC is recorded.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| DTC C1422 is not output |
| DTC C1422 is output |
DTC C1422 is not output
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
DTC C1422 is output
Turn the ignition switch off.
Check the brake pedal height and stop light switch assembly installation.
Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL>ADJUSTMENT
The brake pedal height and stop light switch assembly installation are normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the stop light switch assembly.
Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL
Inspect the stop light switch assembly.
Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A64 skid control ECU (brake actuator assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A64-2 (STP) - A5-1 | Always | Below 1 Ω |
| A64-2 (STP) or A5-1 - Body ground | Always | 10 kΩ or higher |
| A64-22 (STP2) - A5-1* | Always | Below 1 Ω |
| A64-22 (STP2) or A5-1 - Body ground* | Always | 10 kΩ or higher |
*: w/ Stop Light Control Relay
| Proceed to |
|---|
| OK |
| NG |
OK
NG