Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2012.12–2015.10
RM3090E _54 Brake _008767 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0048750 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C1243  Deceleration Sensor  C1245  Malfunction in Deceleration Sensor  C1279  Abnormal Output Voltage in Deceleration Sensor (Test Mode DTC)  C1418  Open or Short in Deceleration Sensor  


DESCRIPTION

The skid control ECU (brake actuator assembly) receives signals from the deceleration sensor. If the sensor functions abnormally, the ABS warning light turns on.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1243 Deceleration Sensor While vehicle speed decreases from 30 km/h (18 mph) to 0 km/h (0 mph), sensor signal does not change 16 times or more.
·

Deceleration sensor

·

Deceleration sensor circuit

·

Skid control ECU (Brake actuator assembly)


C1245 Malfunction in Deceleration Sensor At vehicle speed of 30 km/h (18 mph) or more, difference between back and forth G value calculated using G sensor signals and back and forth G value calculated using vehicle speed, exceeds 0.35 G for 60 seconds or more.
·

Deceleration sensor installation

·

Deceleration sensor

·

Deceleration sensor circuit

·

Skid control ECU (Brake actuator assembly)


C1279 Abnormal Output Voltage in Deceleration Sensor (Test Mode DTC) Detected only during Test Mode.
·

Deceleration sensor installation

·

Deceleration sensor


C1418 Open or Short in Deceleration Sensor One of the following conditions is met when the voltage at terminal IG1 is 9.5 V or higher:
·

The power supply voltage of the deceleration sensor is outside the range of 4.4 to 5.6 V for 1.2 seconds or more.

·

The value of GL1 is outside the range of -1.5 to 1.5 G for 1.2 seconds or more.

·

A deceleration sensor open circuit occurs 7 times or more.


·

Deceleration sensor installation

·

Deceleration sensor

·

Deceleration sensor circuit

·

Skid control ECU (Brake actuator assembly)



WIRING DIAGRAM

A285528E09
2.104,0.729 2.625,0.958 0.521,0.229 10 false GL1 2.073,1.177 2.531,1.406 0.458,0.229 10 false VGS 1.969,1.635 2.417,1.948 0.448,0.313 10 false GGND 1.229,2.115 1.677,2.333 0.448,0.219 10 false N5 1.24,2.281 2.542,2.469 1.302,0.188 10 false Deceleration Sensor 2.469,0.635 3.031,0.938 0.563,0.302 10 false 1 2.469,1.094 2.802,1.365 0.333,0.271 10 false 3 2.469,1.552 2.833,1.823 0.365,0.271 10 false 2 4.552,0.625 5.031,0.906 0.479,0.281 10 false 3 4.49,1.073 4.833,1.313 0.344,0.24 10 false 26 4.5,1.552 4.802,1.792 0.302,0.24 10 false 15 4.75,0.729 5.344,1.01 0.594,0.281 10 false GL1 4.75,1.188 5.188,1.417 0.438,0.229 10 false VGS 4.75,1.656 5.333,2.021 0.583,0.365 10 false GGND 4.25,2 4.729,2.219 0.479,0.219 10 false A63 4.25,2.167 7.083,2.438 2.833,0.271 10 false Skid Control ECU (Brake Actuator Assembly)

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly) or deceleration sensor, perform deceleration sensor zero point calibration and CVT oil pressure calibration (for continuously variable transaxle).

K111: Click hereDrivetrain>K111 MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION

K111F: Click hereDrivetrain>K111F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION


PROCEDURE

1.CHECK DECELERATION SENSOR INSTALLATION

Result:
Result Proceed to
The sensor is tightened to the specified torque and the sensor is not tilted. A
The sensor is not tightened to the specified torque or the sensor is tilted. B



A

2.READ VALUE USING GTS (DECELERATION SENSOR)

B

2.READ VALUE USING GTS (DECELERATION SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


e.

According to the display on the GTS, read the Data List.


Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Deceleration Sensor Deceleration sensor reading Min.: -18.525 m/s2, Max.: 18.387 m/s2 - During deceleration/acceleration:
Changes continuously
for 2WD:
The item is displayed on the GTS but not used.
Chassis > ABS/VSC/TRC > Data List
Tester Display
Deceleration Sensor
50003 105 14
f.

Check that the deceleration value of the deceleration sensor displayed on the GTS changes when the vehicle is tilted.

OK:

Deceleration value changes.


Result:
Proceed to
OK
NG




OK

3.RECONFIRM DTC

NG

4.INSPECT DECELERATION SENSOR
3.RECONFIRM DTC
a.

Clear the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Drive the vehicle at a speed of 30 km/h (19 mph) or more for at least 60 seconds or more.


d.

Check if the same DTCs are recorded.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Proceed to
DTC is output
DTC is not output




DTC is output

4.INSPECT DECELERATION SENSOR

DTC is not output

4.INSPECT DECELERATION SENSOR
a.

Turn the ignition switch off.





OK

5.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - DECELERATION SENSOR)

NG

5.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - DECELERATION SENSOR)
a.

Disconnect the A63 skid control ECU (brake actuator assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A63-3 (GL1) - N5-1 (GL1) Always Below 1 Ω
A63-26 (VGS) - N5-3 (VGS) Always Below 1 Ω
A63-15 (GGND) - N5-2 (GGND) Always Below 1 Ω
A63-3 (GL1) or N5-1 (GL1) - Body ground Always 10 kΩ or higher
A63-26 (VGS) or N5-3 (VGS) - Body ground Always 10 kΩ or higher
A63-15 (GGND) or N5-2 (GGND) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR