The heater assembly receives engine operation signals from the battery current sensor assembly*1 or generator assembly*2. If this circuit is open, the heater assembly will determine that the engine operation signals indicate on. If this circuit is shorted, the heater assembly will determine that the engine operation signals indicate off and the heater assembly will not operate.
*1: w/ Stop and Start System
*2: w/o Stop and Start System
First, confirm that there are no malfunctions in the LIN communication systems. Refer to the how to proceed with troubleshooting procedure.
Remove the generator assembly.
for 1AD-FTV:
Click herePower Source / Network>1AD-FTV BATTERY / CHARGING>GENERATOR>REMOVAL
for 2AD-FHV:
Click herePower Source / Network>2AD-FHV BATTERY / CHARGING>GENERATOR>REMOVAL
for 2AD-CCo, 2AD-DPF:
Click herePower Source / Network>2AD-FTV BATTERY / CHARGING>GENERATOR>REMOVAL
Inspect the generator assembly.
for 1AD-FTV:
Click herePower Source / Network>1AD-FTV BATTERY / CHARGING>GENERATOR>INSPECTION
for 2AD-FHV:
Click herePower Source / Network>2AD-FHV BATTERY / CHARGING>GENERATOR>INSPECTION
for 2AD-CCo, 2AD-DPF:
Click herePower Source / Network>2AD-FTV BATTERY / CHARGING>GENERATOR>INSPECTION
| Proceed to |
|---|
| OK (w/ Stop and Start System) |
| OK (w/o Stop and Start System) |
| NG |
OK (w/ Stop and Start System)
OK (w/o Stop and Start System)
NG
for 1AD-FTV:
Click herePower Source / Network>1AD-FTV BATTERY / CHARGING>GENERATOR>REMOVAL
for 2AD-FHV:
Click herePower Source / Network>2AD-FHV BATTERY / CHARGING>GENERATOR>REMOVAL
for 2AD-CCo, 2AD-DPF:
Click herePower Source / Network>2AD-FTV BATTERY / CHARGING>GENERATOR>REMOVAL
| *a | Front view of wire harness connector
(to Heater Assembly) |
Disconnect the heater assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A33-8 (+) - Body ground | Engine is running (Generator assembly operate) | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Heater Assembly) |
Disconnect the heater assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A33-8 (+) - Body ground | Engine is running (Generator assembly operate) | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A33 heater assembly connector.
Disconnect the A58 battery current sensor assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A33-8 (+) - A58-8 (ALTL) | Always | Below 1 Ω |
| A33-8 (+) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
for 1AD-FTV:
Click herePower Source / Network>1AD-FTV BATTERY / CHARGING>BATTERY CURRENT SENSOR>REMOVAL
for 2AD-FHV:
Click herePower Source / Network>2AD-FHV BATTERY / CHARGING>BATTERY CURRENT SENSOR>REMOVAL
for 2AD-CCo, 2AD-DPF:
Click herePower Source / Network>2AD-FTV BATTERY / CHARGING>BATTERY CURRENT SENSOR>REMOVAL
NG
Disconnect the A33 heater assembly connector.
Disconnect the B61 generator assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A33-8 (+) - B61-4 (L) | Always | Below 1 Ω |
| A33-8 (+) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
for 1AD-FTV:
Click herePower Source / Network>1AD-FTV BATTERY / CHARGING>GENERATOR>REMOVAL
for 2AD-FHV:
Click herePower Source / Network>2AD-FHV BATTERY / CHARGING>GENERATOR>REMOVAL
for 2AD-CCo, 2AD-DPF:
Click herePower Source / Network>2AD-FTV BATTERY / CHARGING>GENERATOR>REMOVAL
NG