Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
3.REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL
Using a moulding remover, detach the 2 clips, 5 claws and 2 guides and remove the rear power window regulator switch assembly with rear door armrest base panel.
Disconnect the connector.
84810D
4.REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY
74646A
5.REMOVE DOOR ASSIST GRIP COVER LH
Using a moulding remover, detach the 5 claws, 2 clips and guide and remove the door assist grip cover LH.
69284D
6.REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG LH
Detach the 3 claws and remove the rear door inside bezel plug LH.
67604
7.REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH
Remove the 3 screws.
Detach the 8 clips and remove the rear door trim board sub-assembly LH.
Disengage the rear door lock remote control cable assembly LH and rear door inside locking cable assembly LH from the 2 clamps.
Disconnect the rear door lock remote control cable and rear door inside locking cable LH.
69206C
8.REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY LH
Detach the 2 claws and guide and remove the rear door inside handle sub-assembly LH.
68174A
9.REMOVE REAR DOOR INNER GLASS WEATHERSTRIP LH
Raise the 6 claws of the rear door inner glass weatherstrip LH as shown in the illustration, and then remove the rear door inner glass weatherstrip LH from the rear door trim board sub-assembly LH.
86160B
10.REMOVE REAR SPEAKER ASSEMBLY (w/ Speaker)
86262D
11.REMOVE REAR DOOR SPEAKER COVER (w/o Speaker)
Disconnect the connector.
Put a 4 mm (0.157 in.) drill bit into a drill.
Wind tape around the drill bit approximately 5 mm (0.197 in.) from the tip of the drill as shown in the illustration.
Tape the 4 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.
Lightly press the drill against the 3 rivets, drill off the flanges of the 3 rivets and remove the rear door speaker cover.
| Area | Specified Condition |
| A | 5 mm (0.197 in.) |
Be careful of the drilled rivet as it may become hot.
Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.
Do not pry the rivet with the drill because this may cause damage to the installation holes of the rivet or the drill bit.
Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled area.
67842E
12.REMOVE REAR DOOR SERVICE HOLE COVER LH
Disconnect the connector of the rear door lock assembly LH.
Pull out the rear door lock remote control cable LH, rear door inside locking cable LH and wire harness from the rear door service hole cover LH, and then remove the rear door service hole cover LH.
Remove any remaining butyl tape from the rear door panel.
67408E
13.REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH
Temporarily install the rear power window regulator switch assembly with rear door armrest base panel.
Connect the cable to the negative (-) battery terminal.
Move the rear door window regulator sub-assembly LH so that the rear door glass channel can be seen.
Disconnect the cable from the negative (-) battery terminal.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
Remove the rear power window regulator switch assembly with rear door armrest base panel.
Remove the screw and 2 bolts.
Remove the rear door window division bar sub-assembly LH together with the rear door glass run as shown in the illustration.
Remove the rear door window division bar sub-assembly LH from the rear door glass run LH.
68124B
14.REMOVE REAR DOOR QUARTER WINDOW GLASS LH
Remove the rear door quarter window glass LH.
68189
15.REMOVE REAR DOOR QUARTER WINDOW WEATHERSTRIP LH
Remove the rear door quarter window weatherstrip LH from the rear door quarter window glass LH.
68104
16.REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH
Remove the rear door glass sub-assembly LH from the rear door window regulator sub-assembly LH as shown in the illustration.
Do not damage the door glass.
69906B
17.REMOVE REAR DOOR GLASS CHANNEL SUB-ASSEMBLY LH
| *1 | Protective Tape |
Using a screwdriver, remove the rear door glass channel sub-assembly LH.
Tape the screwdriver tip before use.
69975A
18.REMOVE REAR DOOR GLASS CHANNEL FILLER
Remove the rear door glass channel filler.
68152C
19.REMOVE REAR DOOR GLASS RUN LH
Remove the front side of the rear door glass run LH.
69804
20.REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY LH
| *1 | Temporary Bolt |
Disconnect the connector.
Loosen the temporary bolt.
Do not remove the temporary bolt. If the temporary bolt is removed, the rear door window regulator sub-assembly LH may fall and become damaged.
Remove the 3 bolts and rear door window regulator sub-assembly LH.
Remove the temporary bolt from the rear door window regulator sub-assembly LH.
85720D
21.REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
75740
22.REMOVE REAR DOOR BELT MOULDING ASSEMBLY LH
69060A
23.REMOVE REAR DOOR WITH MOTOR LOCK ASSEMBLY LH
69740D
24.REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH
| *A | w/o Double Locking System |
| *B | w/ Double Locking System |
Detach the claw and open the cover.
| *A | w/o Double Locking System |
| *B | w/ Double Locking System |
Remove the rear door lock remote control cable LH.
69780B
25.REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY LH
| *A | w/o Double Locking System |
| *B | w/ Double Locking System |
Detach the 3 claws and open the cover.
| *A | w/o Double Locking System |
| *B | w/ Double Locking System |
Remove the rear door inside locking cable assembly LH.
67836H
26.REMOVE REAR DOOR LOCK CHILD PROTECTION COVER LH
Remove the rear door lock child protection cover LH.
69227L
27.REMOVE REAR DOOR OUTSIDE HANDLE COVER LH
Using a T30 "TORX" socket wrench, loosen the screw and remove the rear door outside handle cover LH.
69240
28.REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY LH
Pull and hold the release plate of the rear door outside handle frame sub-assembly LH as shown in the illustration.
The release plate may interfere with the rear door outside handle assembly and may be damaged when removing the rear door outside handle assembly, unless the release plate of the rear door outside handle frame sub-assembly is pulled and held.
Remove the rear door outside handle assembly LH by sliding and pulling it in the direction indicated by the arrow shown in the illustration.
69241G
29.REMOVE REAR DOOR FRONT OUTSIDE HANDLE PAD
Detach the 3 claws and remove the rear door front outside handle pad.
69242G
30.REMOVE REAR DOOR REAR OUTSIDE HANDLE PAD
Detach the 2 claws and remove the rear door rear outside handle pad.
69204A
31.REMOVE REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH
| *A | Inside |
| *B | Outside |
Using a T30 "TORX" socket wrench, loosen the screw.
Slide the rear door outside handle frame sub-assembly LH to detach the claw of the rear door outside handle frame sub-assembly LH, and then remove it.
68640A
32.REMOVE REAR DOOR CHECK ASSEMBLY LH
Remove the 3 bolts and rear door check assembly LH.
67872
33.REMOVE REAR DOOR WEATHERSTRIP LH
Detach the 19 clips and remove the rear door weatherstrip LH.
67674A
34.REMOVE REAR DOOR FRAME GARNISH LH
Detach the claw and remove the rear door frame garnish LH.
75792
35.REMOVE DOOR WINDOW FRAME MOULDING CLIP
75076
36.REMOVE REAR DOOR OUTSIDE MOULDING SUB-ASSEMBLY LH
75988E
37.REMOVE REAR DOOR OUTSIDE STRIPE LH
75978H
38.REMOVE REAR DOOR LOWER OUTSIDE STRIPE LH
75078
39.REMOVE REAR DOOR LOWER OUTSIDE MOULDING SUB-ASSEMBLY LH
67003C
40.REMOVE REAR DOOR PANEL CUSHION
Detach the 2 claws and remove the rear door panel cushion.