Home › Engine / Hybrid System › 2AD-FTV FUEL › FUEL INJECTOR
RM3090E _51 Engine / Hybrid System _008735 2AD-FTV FUEL _0049724 FUEL INJECTOR A

2AD-FTV FUEL  FUEL INJECTOR  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the injector assemblies (including shuffling the injector assemblies between the cylinders), common rail assembly, intake manifold or cylinder head sub-assembly, it is necessary to replace the injection pipes with new ones.

·

When replacing the fuel supply pump assembly, common rail assembly, intake manifold or cylinder head sub-assembly, it is necessary to replace the fuel inlet pipe sub-assembly with a new one.



PROCEDURE

Hide 23670 1.INSTALL INJECTOR ASSEMBLY

NOTICE:

Before installing the injector assembly, check for carbon, foreign matter, etc. on the seal surfaces of the cylinder head and injector assembly. If there is foreign matter, remove it before installing the injector assembly.


a.

Install 4 new injection nozzle seats to the cylinder head sub-assembly.


b.
A203043C02
1.336,1.149 1.615,1.149 false 1.116,1.074 1.278,1.237 0.162,0.163 10 *1
*1 New O-Ring


Install a new O-ring to each injector assembly.


c.

Apply a light coat of engine oil to the O-ring on each injector assembly.


d.

Install the 4 injector assemblies to the cylinder head sub-assembly.

NOTICE:

Fit the injector assembly to the injection nozzle seats.



e.
A264752C02
3.125,0.146 2.938,0.146 2.938,0.146 2.823,0.323 true 3.167,0.052 3.396,0.219 0.229,0.167 10 *1
*1 Washer


Install the nozzle holder clamps and washers as shown in the illustration.

NOTICE:

Pay attention to the mounting orientation (beveled edge) of the washer.



f.

Temporarily install the No. 1 nozzle holder clamp bolts.

NOTICE:

When temporarily installing the No. 1 nozzle holder clamp bolt to the No. 1 nozzle holder clamp, make sure that the bolt and clamp are not at an angle.


HINT:

Apply a light coat of engine oil to the threads of the No. 1 nozzle holder clamp bolts.



g.

Temporarily install the 4 injection pipes.


h.

Temporarily install the No. 1 nozzle leakage pipe and 4 new gaskets with the 4 union bolts and bolt.


i.

Tighten the 4 nozzle holder clamp bolts.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


j.

Tighten the 4 union bolts of the No. 1 nozzle leakage pipe.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


k.

Tighten the bolt of the nozzle leakage pipe.

Torque:
21 N*m (209 kgf*cm, 15 ft.*lbf)


Hide 23812D 2.INSTALL NO. 2 FUEL PIPE (for CCo)

Hide 23901E 3.INSTALL FUEL TUBE SUB-ASSEMBLY (for DPF)

Hide 5.INSTALL INJECTION PIPE SUB-ASSEMBLY

a.
A271585C01
0.094,0.115 0.406,0.271 0.313,0.156 10 *a 0.094,2.406 0.406,2.563 0.313,0.156 10 *b
*a Common Rail Assembly Side
*b Injector Assembly Side


Using a 14 mm union nut wrench, tighten the 4 injection pipe union nuts on the common rail assembly side.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



b.

Using a 14 mm union nut wrench, tighten the 4 injection pipe union nuts on the injector assembly side.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



c.

Install the 4 No. 2 injection pipe clamps with the 2 bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 23762 6.INSTALL NO. 2 NOZZLE LEAKAGE PIPE

a.

Temporarily install the No. 2 nozzle leakage pipe and a new gasket with the check valve and bolt.


b.

Tighten the check valve.

Torque:
32 N*m (321 kgf*cm, 23 ft.*lbf)


c.

Tighten the bolt.

Torque:
32 N*m (321 kgf*cm, 23 ft.*lbf)


d.

Connect the No. 2 fuel hose, No. 3 fuel hose and No. 4 fuel hose to the No. 2 Nozzle leakage pipe, and slide the 3 clamps to secure the hoses.


Hide 82121 7.CONNECT ENGINE WIRE

a.

Connect the engine wire with the 2 bolts and 5 nuts.

Torque:
7.65 N*m (78 kgf*cm, 68 in.*lbf)


b.

Connect the pressure discharge valve connector.


c.

Connect the diesel turbo pressure sensor connector.


d.

Connect the fuel pressure sensor connector and electric EGR control valve connector.


e.

Connect the glow plug wire harness with the nut and No. 1 screw grommet.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


f.

Connect the 4 fuel injector connectors.


g.

Connect the No. 1 vacuum switching valve connector and vacuum regulating valve connector.


h.

for DPF:

Connect the exhaust fuel addition injector connector.


i.

for DPF:

Install the fuel hose protector with the bolt and attach the clamp.

Torque:
20.5 N*m (209 kgf*cm, 15 ft.*lbf)


j.

Connect the engine coolant temperature sensor connector.


k.

Connect the fuel temperature sensor connector and suction control valve connector.


l.

Install the bolt to the wire harness bracket.

Torque:
7.65 N*m (78 kgf*cm, 68 in.*lbf)


Hide 17801 9.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 17705 10.INSTALL AIR CLEANER CAP SUB-ASSEMBLY

Hide 11.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 12.PERFORM REGISTRATION