Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM(w/o Occupant Classification System)
RM3090E _58 Vehicle Interior _008786 SUPPLEMENTAL RESTRAINT SYSTEMS _0049192 AIRBAG SYSTEM(w/o Occupant Classification System) C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(w/o Occupant Classification System)  B1651/33  Manual Cut off Switch Trouble  


DESCRIPTION

HINT:

"Manual cut off switch" refers to the airbag cutoff switch cylinder.


The airbag cutoff switch cylinder sub-assembly consists of the airbag sensor assembly and airbag cutoff switch cylinder sub-assembly.

The instrument panel passenger airbag assembly can be optionally deactivated via this circuit by turning the airbag cutoff switch cylinder sub-assembly to the "OFF" position.

If the instrument panel passenger airbag assembly is deactivated, the airbag cutoff switch cylinder sub-assembly comes on to inform the passengers.

DTC B1651/33 is stored when a malfunction is detected in the airbag cutoff switch cylinder sub-assembly circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1651/33 Manual Cut off Switch Trouble One of the following conditions is met:
·

The airbag sensor assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the airbag cutoff switch cylinder circuit for 2 seconds.

·

An airbag cutoff switch cylinder malfunction.

·

A airbag sensor assembly malfunction.


·

Instrument panel wire

·

Airbag cutoff switch cylinder sub-assembly

·

Airbag sensor assembly



WIRING DIAGRAM

C262371E01
2.094,1.063 2.573,1.26 0.479,0.198 10 false PMC+ 2.125,2.24 2.604,2.438 0.479,0.198 10 false PMC- 5.594,3.063 5.938,3.26 0.344,0.198 10 false G92 0.344,3.198 3.167,3.406 2.823,0.208 10 false Airbag Cutoff Switch Cylinder Sub-assembly 2.573,1.073 2.813,1.281 0.24,0.208 10 false 2 2.573,2.24 2.813,2.448 0.24,0.208 10 false 1 5.51,1.063 5.76,1.271 0.25,0.208 10 false 11 5.552,2.24 5.813,2.448 0.26,0.208 10 false 12 5.771,1.146 6.302,1.344 0.531,0.198 10 false MSW+ 5.771,2.344 6.302,2.542 0.531,0.198 10 false MSW- 0.344,3.042 0.708,3.229 0.365,0.188 10 false G59 5.563,3.219 7.156,3.469 1.594,0.25 10 false Airbag Sensor Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After replacing the airbag sensor assembly, refer to initialization.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



HINT:

The 11 (MSW+) and 12 (MSW-) terminals in this circuit have an activation prevention mechanism. This mechanism can be used to check for an open circuit in the wire harness. In case of other checks (check for short, short to ground or short to B+), it is necessary to release this mechanism.


PROCEDURE

1.CHECK INSTRUMENT PANEL WIRE
a.
C279115C01
0.719,2.229 1.104,2.427 0.385,0.198 0.5,3.448 0.885,3.646 0.385,0.198 1.323,2.542 1.625,2.385 false 2.292,2.573 1.979,2.385 false 2.74,4.031 2.333,3.594 false 0.979,4.063 2.177,3.604 false 0.833,1.125 1.146,1.281 0.313,0.156 10 *1 2.406,1.469 2.719,1.625 0.313,0.156 10 *2 2.344,2.156 2.656,2.313 0.313,0.156 10 *3 2.76,3.583 3.073,3.74 0.313,0.156 10 *4 0.583,1.792 0.896,1.948 0.313,0.156 10 *a 0.667,3.156 0.979,3.313 0.313,0.156 10 *b 1.01,0.563 1.323,0.719 0.313,0.156 10 D 1.396,0.823 1.708,0.979 0.313,0.156 10 C 1.802,0.823 2.115,0.979 0.313,0.156 10 B 2.167,0.552 2.479,0.708 0.313,0.156 10 A 0.771,2.25 1.083,2.406 0.313,0.156 10 G59 0.563,3.469 0.875,3.625 0.313,0.156 10 G92 1.021,2.573 1.542,2.802 0.521,0.229 10 PMC- 2.25,2.594 2.854,2.823 0.604,0.229 10 PMC+ 0.708,4.135 1.229,4.365 0.521,0.229 10 MSW- 2.542,4.115 3.146,4.344 0.604,0.229 10 MSW+
*1 Airbag Cutoff Switch Cylinder Sub-assembly
*2 Airbag Sensor Assembly
*3 Connector C
*4 Connector B
*a Front view of wire harness connector
(to Airbag Cutoff Switch Cylinder Sub-assembly)
*b Rear view of wire harness connector
(to Airbag Sensor Assembly)


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connectors from the airbag sensor assembly and airbag cut off switch cylinder.


d.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


e.

Turn the ignition switch to ON.


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G59-2 (PMC+) - Body ground Ignition switch ON Below 1 V
G59-1 (PMC-) - Body ground Ignition switch ON Below 1 V



g.

Turn the ignition switch off.


h.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G59-2 (PMC+) - G59-1 (PMC-) Always Below 1 Ω



j.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/o Occupant Classification System)>DIAGNOSIS SYSTEM


k.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G59-2 (PMC+) - G59-1 (PMC-) Always 1 MΩ or higher
G59-2 (PMC+) - Body ground Always 1 MΩ or higher
G59-1 (PMC-) - Body ground Always 1 MΩ or higher



l.

Restore the released activation prevention mechanism of connector B to its original condition.


Result:
Proceed to
OK
NG



OK

2.INSPECT AIRBAG CUTOFF SWITCH CYLINDER SUB-ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE

2.INSPECT AIRBAG CUTOFF SWITCH CYLINDER SUB-ASSEMBLY
a.

Remove the airbag cutoff switch cylinder sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG CUT-OFF SWITCH>REMOVAL


b.

Inspect the airbag cutoff switch cylinder sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG CUT-OFF SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK AIR BAG SENSOR ASSEMBLY

NG

REPLACE AIRBAG CUTOFF SWITCH CYLINDER SUB-ASSEMBLY

3.CHECK AIR BAG SENSOR ASSEMBLY
a.
C146229C15
1.042,0.99 1.354,1.146 0.313,0.156 10 *1 2.125,1.333 2.438,1.49 0.313,0.156 10 *2
*1 Airbag Cutoff Switch Cylinder Sub-assembly
*2 Airbag Sensor Assembly


Connect the connectors to the airbag sensor assembly and airbag cutoff switch cylinder.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/o Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/o Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B1651/33 is not output
DTC B1651/33 is output


HINT:

Codes other than DTC B1651/33 may be output at this time, but they are not related to this check.




DTC B1651/33 is not output

DTC B1651/33 is output