Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM(for 1AD-FTV) › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _009049 STOP AND START _0049492 STOP AND START SYSTEM(for 1AD-FTV) C

STOP AND START  STOP AND START SYSTEM(for 1AD-FTV)  P1541  Brake Booster Sensor Circuit  


DESCRIPTION

The engine stop and start ECU determines changes in the brake booster assembly pressure based on the voltage signal received from the vacuum sensor assembly in the brake booster assembly.

If the input value from the vacuum sensor assembly remains the same even though the brake booster assembly pressure changes when the brake pedal is operated or the vehicle is being driven, the engine stop and start ECU judges that the sensor is stuck.

When sticking of the sensor is detected, the engine stop and start ECU stores DTC P1541 and blinks the stop and start cancel indicator light.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
P1541 Brake Booster Sensor Circuit The following condition is met (1 trip detection logic):
·

Vacuum does not change while brake pedal is operated 3 times in a row.


Both of the following conditions are met (1 trip detection logic):
·

Vehicle speed exceeds 30 km/h (18.6 mph) 30 times or more.

·

Changes in vacuum (difference between the maximum and minimum values) is 0.3 kPa (0.003 kgf/cm2, 0.04 psi) or less.


·

Vacuum sensor assembly

·

Brake booster assembly

·

Check valve to connector tube hose (Brake booster hose)

·

Engine stop and start ECU


Blinking DTC stored

CONFIRMATION DRIVING PATTERN

HINT:

DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>DTC CHECK / CLEAR


CONFIRMATION AFTER TROUBLESHOOTING


HINT:
·

When the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited for a certain amount of time. After connecting the cable, drive the vehicle until stop and start control is permitted (approximately 15 to 40 minutes).

·

Allow the engine to idle for 3 minutes after the engine warms up and check that the engine speed is within 50 rpm of the target idle speed.



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>DTC CHECK / CLEAR

Powertrain > Stop and Start > Clear DTCs
50002 227

d.

Start the engine and warm it up.


e.

Enter the following menus: Powertrain / Stop and Start / Data List / Brake Boost Pressure.

Powertrain > Stop and Start > Data List
Tester Display
Brake Boost Pressure
50003 227 61

f.

Drive the vehicle at 30 km/h (18.6 mph) or more and stop the vehicle. Repeat this driving pattern 30 times to allow the brake booster vacuum to change.


g.

Stop the vehicle.


h.

Check that DTCs are not output.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>DTC CHECK / CLEAR

Powertrain > Stop and Start > Trouble Codes
50001 227


STOP AND START SYSTEM OPERATION CHECK


HINT:

When the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited for a certain amount of time. After connecting the cable, drive the vehicle until stop and start control is permitted (approximately 15 to 40 minutes).


a.

Start the engine and warm it up.


b.

Turn the air conditioning system off.


c.

Drive the vehicle at 7 km/h (4.3 mph) or more.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.



d.

Stop the vehicle, move the shift lever to neutral and release the clutch pedal.


e.

Allow the engine to stop by stop and start control.


f.

Depress the clutch pedal and start the engine.



CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>REGISTRATION

·

After replacing the engine stop and start ECU or airbag sensor assembly, perform deceleration sensor zero point clear and calibration.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>REGISTRATION



HINT:
·

DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>DTC CHECK / CLEAR

·

Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>FREEZE FRAME DATA



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Stop and Start / Trouble Codes.


e.

Read the other DTCs.

Powertrain > Stop and Start > Trouble Codes
50001 227
Result:
Proceed to
Other DTCs are not output
Other DTCs are output




Other DTCs are not output

2.READ VALUE USING GTS (BRAKE BOOST PRESSURE)

Other DTCs are output

2.READ VALUE USING GTS (BRAKE BOOST PRESSURE)
a.

Start the engine and warm it up.


b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Stop and Start / Data List / Brake Boost Pressure.


f.

Depress the brake pedal 5 times and read the changes in the following pressure value.

Powertrain > Stop and Start > Data List
Tester Display Normal Condition Diagnostic Note
Brake Boost Pressure Changes by 20 kPa (0.2 kgf/cm2, 2.9 psi) or higher Condition:
·

Ignition switch ON

·

Brake pedal depressed 5 times


Powertrain > Stop and Start > Data List
Tester Display
Brake Boost Pressure
50003 227 61

Result:
Proceed to
NG
OK



NG

3.INSPECT CHECK VALVE TO CONNECTOR TUBE HOSE (BRAKE BOOSTER HOSE)

OK

3.INSPECT CHECK VALVE TO CONNECTOR TUBE HOSE (BRAKE BOOSTER HOSE)
a.

Check the check valve to connector tube hose (brake booster hose) for cracks or clogging (visual check).

OK:

No cracks or clogging in the check valve to connector tube hose (brake booster hose).



Result:
Proceed to
OK
NG



OK

4.REPLACE VACUUM SENSOR ASSEMBLY

NG

REPLACE CHECK VALVE TO CONNECTOR TUBE HOSE

4.REPLACE VACUUM SENSOR ASSEMBLY
a.

Replace the vacuum sensor assembly.

Click hereEngine / Hybrid System>STOP AND START>VACUUM SENSOR ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CLEAR DTC
5.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the GTS on.


c.

Enter the following menus: Powertrain / Stop and Start / Trouble Codes.


d.

Clear the DTC.

Powertrain > Stop and Start > Clear DTCs
50002 227

Result:
Proceed to
NEXT



NEXT

6.CHECK DTC OUTPUT
6.CHECK DTC OUTPUT
a.

Start the engine and warm it up.


b.

Turn the GTS on.


c.

Enter the following menus: Powertrain / Stop and Start / Data List / Brake Boost Pressure.

Powertrain > Stop and Start > Data List
Tester Display
Brake Boost Pressure
50003 227 61

d.

Drive the vehicle at 30 km/h (18.6 mph) or more and stop the vehicle. Repeat this driving pattern 30 times to allow the brake booster vacuum to change.


e.

Stop the vehicle.


f.

Check that no DTCs are output.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>DTC CHECK / CLEAR

Powertrain > Stop and Start > Trouble Codes
50001 227
Result:
Proceed to
DTC is not output
DTC is output




DTC is not output

END

DTC is output