Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM(for 1AD-FTV) › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _009049 STOP AND START _0049492 STOP AND START SYSTEM(for 1AD-FTV) C

STOP AND START  STOP AND START SYSTEM(for 1AD-FTV)  P1644  ECU Internal Error  


DESCRIPTION

If a malfunction is detected in the starter circuit, the engine stop and start ECU stores DTC P1644 and illuminates the stop and start cancel indicator light.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
P1644 ECU Internal Error The following condition continues for 0.2 seconds or more (1 trip detection logic):
·

Malfunction in the engine stop and start ECU internal drive circuit for the starter assembly.


·

Wire harness or connector

·

ST relay

·

Engine stop and start ECU


Blinking DTC stored

CONFIRMATION DRIVING PATTERN

HINT:

DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>DTC CHECK / CLEAR


CONFIRMATION AFTER TROUBLESHOOTING


HINT:
·

When the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited for a certain amount of time. After connecting the cable, drive the vehicle until stop and start control is permitted (approximately 15 to 40 minutes).

·

Allow the engine to idle for 3 minutes after the engine warms up and check that the engine speed is within 50 rpm of the target idle speed.



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>DTC CHECK / CLEAR

Powertrain > Stop and Start > Clear DTCs
50002 227

d.

Start the engine and warm it up.


e.

Drive the vehicle at 7 km/h (12.4 mph) or more.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.



f.

Stop the vehicle, move the shift lever to neutral and release the clutch pedal.


g.

Allow the engine to stop by stop and start control.


h.

Depress the clutch pedal and start the engine.


i.

Check that DTCs are not output.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>DTC CHECK / CLEAR

Powertrain > Stop and Start > Trouble Codes
50001 227


STOP AND START SYSTEM OPERATION CHECK


HINT:

When the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited for a certain amount of time. After connecting the cable, drive the vehicle until stop and start control is permitted (approximately 15 to 40 minutes).


a.

Start the engine and warm it up.


b.

Turn the air conditioning system off.


c.

Drive the vehicle at 7 km/h (4.3 mph) or more.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.



d.

Stop the vehicle, move the shift lever to neutral and release the clutch pedal.


e.

Allow the engine to stop by stop and start control.


f.

Depress the clutch pedal and start the engine.



CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>REGISTRATION

·

After replacing the engine stop and start ECU or airbag sensor assembly, perform deceleration sensor zero point clear and calibration.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>REGISTRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>DTC CHECK / CLEAR

·

Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>FREEZE FRAME DATA

·

If DTCs P060B and P1644 are output simultaneously, perform troubleshooting for DTC P060B (Analog to Digital Converter Malfunction) first as it may have caused DTC P1644 (ECU Internal Error) to be stored.

·

If DTCs P0617 and P1644 are output simultaneously, perform troubleshooting for DTC P0617 (Starter Relay Circuit High) first as it may have caused DTC P1644 (ECU Internal Error) to be stored.

·

If DTCs P0641 and P1644 are output simultaneously, perform troubleshooting for DTC P0641 (Sensor Reference Voltage "A" Circuit/Open) first as it may have caused DTC P1644 (ECU Internal Error) to be stored.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P1644)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Stop and Start / Trouble Codes.


e.

Read the DTCs.

Powertrain > Stop and Start > Trouble Codes
50001 227
Result:
Proceed to
DTC P1644 is output
DTC P060B and DTC P1644 are output
DTC P0617 and DTC P1644 are output
DTC P0641 and DTC P1644 are output




DTC P1644 is output

2.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ST RELAY)

DTC P060B and DTC P1644 are output

DTC P0617 and DTC P1644 are output

DTC P0641 and DTC P1644 are output

2.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ST RELAY)

OK

3.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - CLUTCH START SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - CLUTCH START SWITCH ASSEMBLY)

OK

4.INSPECT RELAY (ST RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT RELAY (ST RELAY)

Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (ST RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (ST RELAY - BODY GROUND)

OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR