Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM(for 1AD-FTV) › 2012.12–2013.11
RM3090E _51 Engine / Hybrid System _009049 STOP AND START _0049492 STOP AND START SYSTEM(for 1AD-FTV) J

STOP AND START  STOP AND START SYSTEM(for 1AD-FTV)  Backup Boost Converter Circuit  


DESCRIPTION

A backup boost converter is built into the engine stop and start ECU. The backup boost converter helps maintain the power source voltage when the engine is restarted by stop and start control.

This prevents various functions such as the audio and visual system or navigation system from failing if the power source voltage drops due to the battery voltage dropping when the engine is restarted by stop and start control. If a DTC is output, troubleshoot the DTC first.

HINT:

A relay function and fuse function are provided in the backup boost converter.

If there is a malfunction in any of the electrical system circuits connected to the backup boost converter, the fuse and relay functions shut off the malfunctioning circuit to protect other circuits (remains shut off until next trip).

When the electrical system circuit is shut off, power to the circuit is cut off, causing any systems connected to the circuit to be disabled.

The fuse function is reset* when the ignition switch is turned off. If the malfunction still exists in the electrical system circuit that has been shut off by the relay function, it will be shut off again by the relay and fuse functions the next time the ignition switch is turned to ON.

*: A semiconductor fuse self-resets according to electric signals.

Backup boost converter supplies power to:

·

Main body ECU (multiplex network body ECU)

·

Vehicle stability control system

·

Power steering system

·

Meter/gauge system

·

Audio and visual system or navigation system

·

Automatic glare-resistant EC mirror

·

Lane departure alert system

·

Tire pressure warning system



CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>REGISTRATION

·

After replacing the engine stop and start ECU or airbag sensor assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>REGISTRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK PROBLEM SYMPTOMS
a.

Determine the trouble area by referring to the table below.

Effect on Vehicle Trouble Area/Cause Fail-safe DTC Output Stop and start cancel indicator light Symptom Proceed to
When the engine is restarted by stop and start control, the following symptoms may occur.
·

The audio and visual system or navigation system is reset

·

The combination meter assembly fades out

·

The steering wheel feels heavy when the engine is restarted*

*: A DTC may be stored in the power steering system


Backup boost converter internal malfunction
·

Internal power source malfunction

·

Internal power source overvoltage

·

Duty error

·

Communication cycle error


Stop and start control prohibited P323B Blinks Converter output voltage cannot be boosted when the engine is restarted A
Battery voltage drop
Systems on the converter output side do not operate
BO1 terminal: The audio and visual system or navigation system will not function
IGO1 terminal: All of the following will not operate
·

Vehicle stability control system

·

Power steering system

·

Automatic glare-resistant EC mirror

·

Systems whose power is supplied from the main body ECU (multiplex network body ECU)

·

Lane departure alert system

·

Tire pressure warning system


Overcurrent applied to an output terminal (output terminal relay circuit is shutoff) Stop and start control is prohibited
(Connected ECUs or sensors may detect power source malfunction DTCs)
B22C0 Blinks Systems do not operate as power supply from the converter is cut off A
Systems do not operate
(Due to converter input side malfunction)
IG1 terminal: All of the following do not operate
·

Vehicle stability control system

·

Power steering system

·

Systems whose power is supplied from the main body ECU (multiplex network body ECU)

·

Automatic glare-resistant EC mirror

·

Lane departure alert system

·

Tire pressure warning system


IG2 terminal: The combination meter assembly will not function
ACC terminal: The audio will not function
Converter input circuit malfunction
·

Open or short to GND in IG1 circuit

·

Open or short to GND in IG2 circuit

·

Open or short to GND in ACC circuit


Stop and start control prohibited - Does not blink (Blinks when communication error DTCs are stored) Systems do not operate as power supply from the converter is cut off B
Systems on the converter output side do not operate
(varies depending on the malfunctioning relay circuit the converter detected)
ACO terminal: The audio and visual system or navigation system will not function
IGO2 terminal: The combination meter assembly will not function
Malfunction in circuits the converter supplies power to
(between the converter and ECUs or sensors)
·

Open or short in the combination meter assembly circuit


Related systems do not operate as the relay circuit in the converter is turned off - Does not blink (Blinks when communication error DTCs are stored) Systems do not operate as power supply from the converter is cut off B
All of the following will operate
·

Audio and visual system or navigation system

·

Vehicle stability control system

·

Power steering system

·

Systems whose power is supplied from the main body ECU (multiplex network body ECU)

·

Meter/gauge system

·

Automatic glare-resistant EC mirror

·

Lane departure alert system

·

Tire pressure warning system


·

Open in BBC fuse circuit

·

Short in converter circuit

·

Backup boost converter malfunction


Stop and start control prohibited P0617 Does not blink (Due to disabled meter/gauge system) All systems that the converter supplies power to do not operate (see circuit diagram) A
P323B
The audio and visual system or navigation system does not function
(until the ignition switch is turned off)
Excessive audio volume
Data List item "State of BBC" displays "BBC Overcurrent" while the circuit is protected
The relay circuit in the converter is turned off to cut off power supply to the audio and visual system or navigation system (Returns to normal when the ignition switch is turned off) - Does not blink If overcurrent is detected in the audio and visual system or navigation system, system operation is disabled while the ignition switch is ON
(Returns to normal when the ignition switch is turned off)
C
The audio and visual system or navigation system cannot be turned off (short between ACO and +B)
The combination meter assembly cannot be turned off (short between IGO2 and +B)
Communication error DTCs may be stored due to short between IGO1 and +B
HINT:

Varies depending on the number of times an open occurs in the +B circuit


Converter circuit malfunction
·

Short between ACO and +B

·

Short between IGO1 and +B

·

Short between IGO2 and +B


- - Does not blink The converter cannot shut off power source when the ignition switch is turned off B
Ignition switch does not turn to ACC (short between ACC and +B)
Ignition switch does not turn off (short between IG1 or IG2 and +B)
Engine stop and start ECU power source circuit malfunction
·

Short between ACC and +B

·

Short between IG1 and +B

·

Short between IG2 and +B


- - Does not blink
·

Ignition switch does not turn to ACC

·

Ignition switch does not turn off


B


Result:
Proceed to
A
B
C



A

B

2.CHECK ENGINE STOP AND START ECU (POWER SOURCE CIRCUIT)

C

5.CHECK AUDIO AND VISUAL SYSTEM OR NAVIGATION SYSTEM
2.CHECK ENGINE STOP AND START ECU (POWER SOURCE CIRCUIT)
a.
A285704C10
0.281,3.281 0.625,3.521 0.344,0.24 0.385,1.323 0.729,1.563 0.344,0.24 1.333,2.063 1.448,1.688 false 1.26,4.083 1.354,3.771 false 1.708,4.083 1.573,3.781 false 2.094,4.094 1.885,3.781 false 0.229,0.208 0.563,0.5 0.333,0.292 10 *a 0.438,1.375 0.896,1.573 0.458,0.198 10 A65 0.333,3.323 0.792,3.521 0.458,0.198 10 G87 1.208,2.104 1.667,2.302 0.458,0.198 10 BIN 2,4.115 2.458,4.313 0.458,0.198 10 IG2 1.156,4.115 1.615,4.313 0.458,0.198 10 IG1 1.563,4.115 2.021,4.313 0.458,0.198 10 ACC
*a Front view of wire harness connector:
(to Engine Stop and Start ECU)


Disconnect the A65 and G87 engine stop and start ECU connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A65-7 (BIN) - Body ground Always 9.5 to 14 V



c.

Turn the ignition switch to ACC.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G87-19 (ACC) - Body ground Ignition switch ACC 9.5 to 14 V



e.

Turn the ignition switch to ON.


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G87-17 (IG1) - Body ground Ignition switch ON 9.5 to 14 V
G87-20 (IG2) - Body ground Ignition switch ON 9.5 to 14 V



g.

Turn the ignition switch off.


h.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G87-17 (IG1) - Body ground Ignition switch off 0 to 1 V
G87-19 (ACC) - Body ground Ignition switch off 0 to 1 V
G87-20 (IG2) - Body ground Ignition switch off 0 to 1 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)
a.

Disconnect the connector from the corresponding system ECU/sensor.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Radio Receiver Assembly (for Radio Receiver Type)
Tester Connection Condition Specified Condition
G87-2 (BO1) - G46-4 (+B1) Always Below 1 Ω
G87-3 (ACO) - G46-3 (ACC1) Always Below 1 Ω
G87-2 (BO1) - Body ground Always 10 kΩ or higher
G87-3 (ACO) - Body ground Always 10 kΩ or higher
G46-4 (+B1) - Body ground Always 10 kΩ or higher
G46-3 (ACC1) - Body ground Always 10 kΩ or higher

Navigation ECU Sub-assembly (for Navigation Receiver Type)
Tester Connection Condition Specified Condition
G87-2 (BO1) - G137-4 (+B1) Always Below 1 Ω
G87-3 (ACO) - G137-3 (ACC1) Always Below 1 Ω
G87-2 (BO1) - Body ground Always 10 kΩ or higher
G87-3 (ACO) - Body ground Always 10 kΩ or higher
G137-4 (+B1) - Body ground Always 10 kΩ or higher
G137-3 (ACC1) - Body ground Always 10 kΩ or higher

Radio and Display Receiver Assembly (for Radio and Display Receiver Type)
Tester Connection Condition Specified Condition
G87-2 (BO1) - G141-4 (+B1) Always Below 1 Ω
G87-3 (ACO) - G141-3 (ACC1) Always Below 1 Ω
G87-2 (BO1) - Body ground Always 10 kΩ or higher
G87-3 (ACO) - Body ground Always 10 kΩ or higher
G141-4 (+B1) - Body ground Always 10 kΩ or higher
G141-3 (ACC1) - Body ground Always 10 kΩ or higher

Skid Control ECU (Brake Actuator Assembly)
Tester Connection Condition Specified Condition
G87-12 (IGO1) - A64-34 (IG1)* Always Below 1 Ω
G87-12 (IGO1) - Body ground Always 10 kΩ or higher
A64-34 (IG1) - Body ground Always 10 kΩ or higher

Steering Angle Sensor (Spiral with Sensor Cable Sub-assembly)
Tester Connection Condition Specified Condition
G87-12 (IGO1) - G12-4 (IG) Always Below 1 Ω
G87-12 (IGO1) - Body ground Always 10 kΩ or higher
G12-4 (IG) - Body ground Always 10 kΩ or higher

Power Steering ECU Assembly
Tester Connection Condition Specified Condition
G87-12 (IGO1) - h1-1 (IG) Always Below 1 Ω
G87-12 (IGO1) - Body ground Always 10 kΩ or higher
h1-1 (IG) - Body ground Always 10 kΩ or higher

Combination Meter Assembly
Tester Connection Condition Specified Condition
G87-11 (IGO2) - G16-39 (IG+) Always Below 1 Ω
G87-11 (IGO2) - Body ground Always 10 kΩ or higher
G16-39 (IG+) - Body ground Always 10 kΩ or higher

Instrument Panel Junction Block Assembly (Main Body ECU (Multiplex Network Body ECU))
Tester Connection Condition Specified Condition
G87-12 (IGO1) - 3D-40 (IG) Always Below 1 Ω
G87-12 (IGO1) - Body ground Always 10 kΩ or higher
3D-40 (IG) - Body ground Always 10 kΩ or higher

Inner Rear View Mirror Assembly (w/ Automatic Glare-resistant EC mirror)
Tester Connection Condition Specified Condition
G87-12 (IGO1) - Q6-4 (IG) Always Below 1 Ω
G87-12 (IGO1) - Body ground Always 10 kΩ or higher
Q6-4 (IG) - Body ground Always 10 kΩ or higher

Lane Departure Warning Camera (w/ Lane Departure Alert System)
Tester Connection Condition Specified Condition
G87-12 (IGO1) - Q13-7 (IGB) Always Below 1 Ω
G87-12 (IGO1) - Body ground Always 10 kΩ or higher
Q13-7 (IGB) - Body ground Always 10 kΩ or higher

Tire Pressure Warning ECU and Receiver (w/ Tire Pressure Warning System)
Tester Connection Condition Specified Condition
G87-12 (IGO1) - M30-1 (IG) Always Below 1 Ω
G87-12 (IGO1) - Body ground Always 10 kΩ or higher
M30-1 (IG) - Body ground Always 10 kΩ or higher


*: There is a diode between the electrical wiring for RHD vehicles.



Result:
Proceed to
OK
NG



OK

4.CHECK ENGINE STOP AND START ECU (EACH ECU OR SENSOR POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK ENGINE STOP AND START ECU (EACH ECU OR SENSOR POWER SOURCE CIRCUIT)
A299962C01
0.833,0.646 1.25,0.896 0.417,0.25 0.833,0.365 1.25,0.615 0.417,0.25 0.833,0.083 1.25,0.333 0.417,0.25 4.917,0.167 5.333,0.417 0.417,0.25 1.083,2.333 1.5,2.583 0.417,0.25 1.833,3.833 2.25,4.083 0.417,0.25 4.583,3.75 5,4 0.417,0.25 0.854,5.458 1.271,5.708 0.417,0.25 3.302,5.25 3.719,5.5 0.417,0.25 5.833,5.25 6.25,5.5 0.417,0.25 5,2.333 5.417,2.583 0.417,0.25 1.833,1.333 2.167,1.333 true 1.667,1.167 1.719,0.708 1.719,0.708 1.969,0.708 true 6.583,1.833 6.5,1.833 6.5,1.833 5.531,1.438 false 2.198,3.271 2.417,3.5 2.417,3.5 2.5,3.5 true 2.167,4.625 2.542,4.167 2.542,4.167 2.708,4.167 true 4.5,4.594 4.25,4.417 4.25,4.417 4.083,4.417 true 1.25,6.24 1.594,5.917 1.594,5.917 1.75,5.917 true 3,6.333 2.667,6.333 true 5.531,6.083 5.198,6.083 true 4.583,3.229 5.833,3.833 5.833,3.833 6.167,3.833 true 0.917,0.135 1.375,0.333 0.458,0.198 10 G46 0.875,0.417 1.333,0.615 0.458,0.198 10 G137 0.875,0.688 1.333,0.885 0.458,0.198 10 G141 1.333,0.135 1.646,0.333 0.313,0.198 10 *A 1.333,0.406 1.646,0.604 0.313,0.198 10 *B 1.333,0.677 1.646,0.875 0.313,0.198 10 *C 2.292,1.25 2.75,1.448 0.458,0.198 10 +B1 2.042,0.635 2.5,0.833 0.458,0.198 10 ACC1 5,0.219 5.458,0.417 0.458,0.198 10 A64 6.667,1.75 7,2.083 0.333,0.333 10 IG1 0.521,0.167 0.833,0.365 0.313,0.198 10 *a 4.021,0.167 4.333,0.365 0.313,0.198 10 *b 1.125,2.365 1.583,2.563 0.458,0.198 10 G16 2.583,3.417 2.917,3.75 0.333,0.333 10 IG1 0.271,2.417 0.583,2.615 0.313,0.198 10 *c 1.917,3.885 2.375,4.083 0.458,0.198 10 G12 3.917,2.302 4.229,2.5 0.313,0.198 10 *d 2.75,4.083 3.083,4.417 0.333,0.333 10 IG 1.438,3.833 1.75,4.031 0.313,0.198 10 *e 4.708,3.802 5.167,4 0.458,0.198 10 h1 3.917,4.333 4.25,4.667 0.333,0.333 10 IG 0.958,5.5 1.417,5.698 0.458,0.198 10 Q6 4.25,3.75 4.563,3.948 0.313,0.198 10 *f 0.521,5.302 0.833,5.5 0.313,0.198 10 *g 1.813,5.854 2.146,6.188 0.333,0.333 10 IG 2.854,5.135 3.167,5.333 0.313,0.198 10 *h 3.385,5.302 3.844,5.5 0.458,0.198 10 Q13 5.917,5.302 6.375,5.5 0.458,0.198 10 M30 5.417,5.135 5.729,5.333 0.313,0.198 10 *i 2.417,6.25 2.75,6.583 0.333,0.333 10 IGB 5,6 5.333,6.333 0.333,0.333 10 IG 5.125,2.385 5.583,2.583 0.458,0.198 10 3D 6.25,3.75 6.583,4.083 0.333,0.333 10 IG
*A for Radio Receiver Type *B for Navigation Receiver Type
*C for Radio and Display Receiver Type - -
*a Front view of wire harness connector
(to Radio Receiver Assembly, Navigation ECU Sub-assembly or Radio and Display Receiver Assembly)
*b Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))
*c Front view of wire harness connector
(to Combination Meter Assembly)
*d Front view of wire harness connector
(to Instrument Panel Junction Block Assembly (Main Body ECU (Multiplex Network Body ECU)))
*e Front view of wire harness connector
(to Steering Angle Sensor (Spiral with Sensor Cable Sub-assembly))
*f Front view of wire harness connector
(to Power Steering ECU Assembly)
*g Front view of wire harness connector
(to Inner Rear View Mirror Assembly)
*h Front view of wire harness connector
(to Lane Departure Warning Camera)
*i Front view of wire harness connector
(to Tire Pressure Warning ECU and Receiver)
- -


a.

Disconnect the connector from the corresponding system ECU/sensor.


b.

Measure the voltage according to the value(s) in the table below.

HINT:

Measure the voltage at the corresponding terminals.


Standard Voltage:
Radio Receiver Assembly (for Radio Receiver Type)
Tester Connection Condition Specified Condition
G46-4 (+B1) - Body ground Always 9.5 to 14 V

Navigation ECU Sub-assembly (for Navigation Receiver Type)
Tester Connection Condition Specified Condition
G137-4 (+B1) - Body ground Always 9.5 to 14 V

Radio and Display Receiver Assembly (for Radio and Display Receiver Type)
Tester Connection Condition Specified Condition
G141-4 (+B1) - Body ground Always 9.5 to 14 V



c.

Turn the ignition switch to ACC.


d.

Measure the voltage according to the value(s) in the table below.

HINT:

Measure the voltage at the corresponding terminals.


Standard Voltage:
Radio Receiver Assembly (for Radio Receiver Type)
Tester Connection Switch Condition Specified Condition
G46-3 (ACC1) - Body ground Ignition switch ACC 9.5 to 14 V

Navigation ECU Sub-assembly (for Navigation Receiver Type)
Tester Connection Switch Condition Specified Condition
G137-3 (ACC1) - Body ground Ignition switch ACC 9.5 to 14 V

Radio and Display Receiver Assembly (for Radio and Display Receiver Type)
Tester Connection Switch Condition Specified Condition
G141-3 (ACC1) - Body ground Ignition switch ACC 9.5 to 14 V



e.

Turn the ignition switch to ON.


f.

Measure the voltage according to the value(s) in the table below.

HINT:

Measure the voltage at the corresponding terminals.


Standard Voltage:
Tester Connection Switch Condition Specified Condition
A64-34 (IG1) - Body ground Ignition switch ON 9.5 to 14 V
G16-39 (IG+) - Body ground Ignition switch ON 9.5 to 14 V
G12-4 (IG) - Body ground Ignition switch ON 9.5 to 14 V
h1-1 (IG) - Body ground Ignition switch ON 9.5 to 14 V
3D-40 (IG) - Body ground Ignition switch ON 9.5 to 14 V
Q6-4 (IG) - Body ground*1 Ignition switch ON 9.5 to 14 V
Q13-7 (IGB) - Body ground*2 Ignition switch ON 9.5 to 14 V
M30-1 (IG) - Body ground*3 Ignition switch ON 9.5 to 14 V


*1: w/ Automatic Glare-resistant EC Mirror

*2: w/ Lane Departure Alert System

*3: w/ Tire Pressure Warning System



Result:
Proceed to
OK
NG



OK

CHECK POWER SOURCE CIRCUIT (POWER SOURCE CIRCUIT OF RELATED SYSTEM)

NG

5.CHECK AUDIO AND VISUAL SYSTEM OR NAVIGATION SYSTEM
a.

Turn the ignition switch off and wait for 1 minute.


b.

Turn the ignition switch to ON.


c.

Lower the audio volume.


d.

for Radio Receiver Type/Radio and Display Receiver Type:

Check if the audio and visual system operates normally.

OK:

Audio and visual system operates normally.



e.

for Navigation Receiver Type:

Check if the navigation system operates normally.

OK:

Navigation system operates normally.



Result:
Proceed to
NG
OK



NG

6.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - RADIO AND DISPLAY RECEIVER)

OK

END

6.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - RADIO AND DISPLAY RECEIVER)
a.

Disconnect the G87 engine stop and start ECU connector.


b.

for Radio Receiver Type:

Disconnect the G46 radio receiver assembly connector.


c.

for Navigation Receiver Type:

Disconnect the G137 navigation ECU sub-assembly connector.


d.

for Radio and Display Receiver Type:

Disconnect the G141 radio and display receiver assembly connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for Radio Receiver Type:
Tester Connection Condition Specified Condition
G87-2 (BO1) - Body ground Always 10 kΩ or higher
G46-4 (+B1) - Body ground Always 10 kΩ or higher
G87-3 (ACO) - Body ground Always 10 kΩ or higher
G46-3 (ACC1) - Body ground Always 10 kΩ or higher

for Navigation Receiver Type:
Tester Connection Condition Specified Condition
G87-2 (BO1) - Body ground Always 10 kΩ or higher
G137-4 (+B1) - Body ground Always 10 kΩ or higher
G87-3 (ACO) - Body ground Always 10 kΩ or higher
G137-3 (ACC1) - Body ground Always 10 kΩ or higher

for Radio and Display Receiver Type:
Tester Connection Condition Specified Condition
G87-2 (BO1) - Body ground Always 10 kΩ or higher
G141-4 (+B1) - Body ground Always 10 kΩ or higher
G87-3 (ACO) - Body ground Always 10 kΩ or higher
G141-3 (ACC1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK (for Radio Receiver Type/Radio and Display Receiver Type)
OK (for Navigation Receiver Type)
NG



OK (for Radio Receiver Type/Radio and Display Receiver Type)

OK (for Navigation Receiver Type)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR