Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › BLACK OUT TAPE(for Rear Door)
RM3090E _59 Vehicle Exterior _008798 EXTERIOR PANELS / TRIM _0050116 BLACK OUT TAPE(for Rear Door) A

EXTERIOR PANELS / TRIM  BLACK OUT TAPE(for Rear Door)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.

·

A bolt without a torque specification is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS



PROCEDURE

Hide 75978H 2.INSTALL REAR DOOR LOWER OUTSIDE STRIPE LH

HINT:

When installing the rear door lower outside stripe, heat the rear door panel and rear door lower outside stripe using a heat light.


Standard:
Item Temperature
Rear Door Panel 40 to 60°C (104 to 140°F)
Rear Door Lower Outside Stripe 20 to 30°C (68 to 86°F)


NOTICE:

Do not heat the rear door panel or rear door lower outside stripe excessively.


a.
B340215E01
3.01,2.458 3.167,2.656 0.156,0.198 10 a 2.49,2.406 2.646,2.604 0.156,0.198 10 a 1.542,0.146 1.875,0.333 0.333,0.188 10 a - a 2.646,0.167 2.802,0.344 0.156,0.177 10 A 2.063,0.177 2.219,0.354 0.156,0.177 10 B

Refer to the illustration to position a new rear door lower outside stripe.

Reference Value:
Area Specified Condition
A 2 to 4 mm (0.0787 to 0.157 in.)
B 5 mm (0.1969 in.)



b.

Remove the release paper from the rear door lower outside stripe.


Hide 75988E 3.INSTALL REAR DOOR OUTSIDE STRIPE LH

HINT:

When installing the rear door outside stripe, heat the rear door panel and rear door outside stripe using a heat light.


Standard:
Item Temperature
Rear Door Panel 40 to 60°C (104 to 140°F)
Rear Door Outside Stripe 20 to 30°C (68 to 86°F)


NOTICE:

Do not heat the rear door panel or rear door outside stripe excessively.


a.
B340217E01
2.094,1.698 2.25,1.896 0.156,0.198 10 a 1.979,2.25 2.135,2.448 0.156,0.198 10 a 2.656,1.781 2.813,1.979 0.156,0.198 10 b 2.76,2.396 2.917,2.594 0.156,0.198 10 b 0.146,0.135 0.531,0.385 0.385,0.25 10 a - a 2.188,0.135 2.573,0.385 0.385,0.25 10 b - b 0.698,0.229 0.854,0.427 0.156,0.198 10 A 0.427,0.594 0.583,0.792 0.156,0.198 10 B 3.135,0.542 3.292,0.74 0.156,0.198 10 C

Refer to the illustration to position a new rear door outside stripe.

Reference Value:
Area Specified Condition
A 2 to 4 mm (0.0787 to 0.157 in.)
B 5 mm (0.1969 in.)
C 1.5 to 2.5 mm (0.0591 to 0.0984 in.)



b.

Remove the release paper from the rear door outside stripe.


Hide 75792 4.INSTALL DOOR WINDOW FRAME MOULDING CLIP

Hide 75076 5.INSTALL REAR DOOR OUTSIDE MOULDING SUB-ASSEMBLY LH

Hide 75740 7.INSTALL REAR DOOR BELT MOULDING ASSEMBLY LH

Hide 68104 8.INSTALL REAR DOOR GLASS SUB-ASSEMBLY LH

Hide 68124B 9.INSTALL REAR DOOR QUARTER WINDOW GLASS LH

Hide 67408E 10.INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH

Hide 68152C 11.INSTALL REAR DOOR GLASS RUN LH

Hide 67842E 12.INSTALL REAR DOOR SERVICE HOLE COVER LH

Hide 67604 13.INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

Hide 69284D 14.INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG LH

Hide 74646A 15.INSTALL DOOR ASSIST GRIP COVER LH

Hide 16.INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL

Hide 17.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION