Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › BLACK OUT TAPE(for Front Door)
RM3090E _59 Vehicle Exterior _008798 EXTERIOR PANELS / TRIM _0050115 BLACK OUT TAPE(for Front Door) A

EXTERIOR PANELS / TRIM  BLACK OUT TAPE(for Front Door)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.

·

A bolt without a torque specification is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS



PROCEDURE

Hide 1. REPAIR INSTRUCTION

a.

Clean the vehicle body surface.

i.

Using a heat light, heat the vehicle body surface.


ii.

Wipe off any tape adhesive residue with cleaner.



b.

Installation temperature.

i.

When the ambient temperature is below 15°C (59°F), perform the installation procedure after warming the vehicle body surface (installation surface of the door frame) and tape to between 20 and 30°C (68 and 86°F) using a heat light. When the ambient temperature is higher than 35°C (95°F), cool the vehicle body surface (installation surface of the door frame) and tape to between 20 and 30°C (68 and 86°F) prior to installation.

HINT:
·

The most appropriate temperature for installing the tape is 25°C (77°F).

·

When the temperature is low, the tape turns stiff and falls off easily. When the temperature is high, the tape loses elasticity.





c.

Before installation.

i.

Make sure any dirt on and around the vehicle body surface where the tape will be installed (installation surface of the door frame) is removed, and that the surface is smooth. If the surface is rough or dirt remains when pressing the tape onto the surface, air will be trapped under the tape and result in a poor appearance.

HINT:

Spray water on the shop floor to settle any dust.




d.

Key points for handling the tape.

i.

The tape bends and rolls up easily. Store the tape between flat pieces of cardboard or other similar objects and keep it dry and level.

NOTICE:

Do not bend the tape or leave it in a place with a high temperature.




e.

Key points for the installation of the tape (how to use a squeegee and the installation procedure for a flat surface).

NOTICE:
·

Position the tape with a high level of accuracy to achieve a neat finish and to avoid peeling.

·

The tape cannot be reused because it deforms and will not fit after removal.



i.

To avoid air bubbles, slightly raise the part of the tape that is going to be applied so that its adhesive surface does not touch the vehicle body while applying the tape. Tilt the squeegee 40 to 50° (for pressing forward) or 30 to 45° (for pulling) from the vehicle body surface and press with a force of 20 to 30 N (2 to 3 kgf) while moving the squeegee at a constant slow speed of 3 to 7 cm (1.2 to 2.8 in.) per second.

B233855C06
0.083,0.073 3.875,1.563 3.792,1.49 0.688,0.625 0.833,0.479 0.833,0.479 1,0.479 false 2.177,0.698 2.292,0.323 2.292,0.323 2.542,0.323 false 2.156,1.24 2.813,1.24 false 2.146,1.99 2.146,1.823 2.146,1.823 2.604,1.823 false 2.094,3.427 2.646,3.427 false 4.594,2.625 4.99,2.625 false 4.875,3.052 5.302,3.052 false 5.729,2.604 5.969,2.948 5.969,2.948 6.083,2.948 false 5.677,3.271 6.073,3.271 false 1.042,2.844 1.802,2.844 1.802,2.844 2.042,2.292 false 1.125,3.25 1.646,3.25 false 0.865,2.344 1.75,2.521 0.885,0.177 10 3 to 7 cm/sec. 3.885,2.219 4.771,2.396 0.885,0.177 10 3 to 7 cm/sec. 2.677,1.75 3.25,1.927 0.573,0.177 10 40 to 50° 6.135,2.885 6.708,3.063 0.573,0.177 10 30 to 45° 2.844,2.563 3.635,2.74 0.792,0.177 10 10 to 20 mm 6.125,2.521 6.917,2.698 0.792,0.177 10 10 to 20 mm 0.125,0.115 0.313,0.271 0.188,0.156 10 *a 2.552,0.25 2.74,0.417 0.188,0.167 10 *b 2.833,1.177 3.01,1.323 0.177,0.146 10 *c 1.021,0.396 1.188,0.542 0.167,0.146 10 *1 0.885,2.771 1.052,2.917 0.167,0.146 10 *1 0.083,1.594 0.302,1.76 0.219,0.167 10 *A 0.958,3.177 1.125,3.344 0.167,0.167 10 *2 4.438,2.573 4.604,2.719 0.167,0.146 10 *1 4.708,2.979 4.875,3.146 0.167,0.167 10 *2 2.667,3.354 2.865,3.521 0.198,0.167 10 *3 3.656,1.615 3.854,1.781 0.198,0.167 10 *B 6.104,3.198 6.281,3.365 0.177,0.167 10 *3
*A Pressing *B Pulling
*1 Squeegee *2 Black Out Tape
*3 Release Paper - -
*a Sectional View *b Non-padded Side
*c Padded Side - -


NOTICE:

Be sure to observe the specified pressing speed, force and angle of the squeegee to avoid wrinkles and air bubbles.


HINT:
·

Either angle of the squeegee (for pressing forward or for pulling) is acceptable.

·

Be sure to apply the tape while removing the release paper 10 to 20 mm (0.393 to 0.787 in.) from the edge of the squeegee.





f.
B233856C06
0.972,1.789 1.087,1.789 1.087,1.789 1.2,1.697 false 0.736,1.699 0.93,1.859 0.193,0.161 10 *1 2.335,0.435 2.514,0.615 0.179,0.179 10 *a 1.63,0.332 1.823,0.507 0.193,0.175 10 *b 0.908,0.424 1.116,0.617 0.207,0.193 10 *c
*1 Squeegee
*a First
*b Second
*c Third


Key points for the installation of the tape (how to use a squeegee and the installation procedure for hemming surfaces).

i.

If it is difficult to press the tape, press it in several steps as shown in the illustration. Use your fingers or the padded surface of a squeegee to slowly apply the tape to the hem of the vehicle, especially for a small hem.

HINT:

When applying tape to the backside of a hem, remove the release paper and use your fingers or the padded surface of a squeegee.




g.

Key points for the installation of the tape (how to use a squeegee and the installation procedure for corners).

i.

Remove the release paper and apply the tape carefully with your fingers.


ii.

Before applying the tape to each corner, heat the tape using a heat light and gradually apply it to avoid wrinkles in the tape and achieve a neat finish.



h.

Check after installation.

i.

After completing the application, check if the tape is applied neatly. If the tape is not applied neatly, apply new tape.

NOTICE:

Do not reuse the tape.




Hide 75922M 2.INSTALL NO. 1 BLACK OUT TAPE LH

HINT:

When installing the No. 1 black out tape, heat the front door panel and No. 1 black out tape using a heat light.


Standard:
Item Temperature
Front Door Panel 40 to 60°C (104 to 140°F)
No. 1 Black Out Tape 20 to 30°C (68 to 86°F)


NOTICE:

Do not heat the front door panel or No. 1 black out tape excessively.


a.
B340214E01
2.646,2.76 2.802,2.958 0.156,0.198 10 a 2.5,3.281 2.656,3.479 0.156,0.198 10 a 0.146,0.198 0.479,0.385 0.333,0.188 10 a - a 1.365,0.573 1.521,0.771 0.156,0.198 10 A 1.646,1.24 1.802,1.438 0.156,0.198 10 B

Refer to the illustration to position a new No. 1 black out tape.

Reference Value:
Area Specified Condition
A 2 to 4 mm (0.0787 to 0.157 in.)
B 5 mm (0.1969 in.)



b.

Remove the release paper from the No. 1 black out tape.


Hide 75792 3.INSTALL DOOR WINDOW FRAME MOULDING CLIP

Hide 75756C 4.INSTALL FRONT DOOR WINDOW REAR FRAME MOULDING LH

Hide 75720 6.INSTALL FRONT DOOR BELT MOULDING ASSEMBLY LH

Hide 68151D 7.INSTALL FRONT DOOR GLASS RUN LH

Hide 68102 8.INSTALL FRONT DOOR GLASS SUB-ASSEMBLY LH

Hide 67832 9.INSTALL FRONT DOOR SERVICE HOLE COVER LH

Hide 87940 10.INSTALL OUTER REAR VIEW MIRROR ASSEMBLY LH

Hide 67602 11.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

Hide 69284C 12.INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG LH

Hide 74642A 13.INSTALL FRONT DOOR ASSIST GRIP COVER LH

Hide 14.INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL

Hide 67492A 15.INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH LH

Hide 16.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION