Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM(w/o Occupant Classification System)
RM3090E _58 Vehicle Interior _008788 SEAT BELT _0049193 SEAT BELT WARNING SYSTEM(w/o Occupant Classification System) J

SEAT BELT  SEAT BELT WARNING SYSTEM(w/o Occupant Classification System)  Rear Seat Belt Warning Light Malfunction  


DESCRIPTION

When a rear door is opened and closed (the rear door courtesy light switch turns on and off) with the ignition switch ON, or when a rear door is opened and closed (the rear door courtesy light switch turns on and off) and then the ignition switch is turned to ON, the rear seat belt warning light in the combination meter assembly turns on to inform the driver of condition of the rear seat belts. If a rear seat belt is fastened or unfastened, the warning light changes to indicate the current condition of the rear seat belts.

Only for vehicles with a rear seat belt indicator.

WIRING DIAGRAM

C279309E01
3.281,0.729 3.99,0.927 0.708,0.198 10 false LCTY 3.292,1.708 4,1.906 0.708,0.198 10 false RCTY 3.031,0.594 3.344,0.792 0.313,0.198 10 false 24 3.125,1.604 3.438,1.802 0.313,0.198 10 false 6 2.104,1.594 2.417,1.792 0.313,0.198 10 false 1 2.115,0.615 2.427,0.813 0.313,0.198 10 false 1 3.021,2.135 3.729,2.333 0.708,0.198 10 false G78 3.01,2.302 5.188,2.667 2.177,0.365 10 false Main Body ECU (Multiplex Network Body ECU) 1,0.99 1.708,1.188 0.708,0.198 10 false N8 0.979,1.135 3.198,1.469 2.219,0.333 10 false Rear Door Courtesy Light Switch Assembly LH 1.177,1.969 1.885,2.167 0.708,0.198 10 false M6 1.156,2.115 2.729,2.458 1.573,0.344 10 false Rear Door Courtesy Light Switch Assembly RH 0.604,3.729 1.313,3.927 0.708,0.198 10 false M14 2.25,4.323 2.958,4.521 0.708,0.198 10 false M13 0.594,3.906 2.031,4.25 1.438,0.344 10 false Rear Seat Inner Belt Assembly LH 2.229,4.49 3.479,4.844 1.25,0.354 10 false Rear Center Lap Type Seat Belt Assembly RH 3.448,4.979 4.156,5.177 0.708,0.198 10 false M12 3.417,5.125 5.75,5.333 2.333,0.208 10 false Rear Seat Inner Belt Assembly RH 1.542,2.802 1.854,3 0.313,0.198 10 false 1 1.531,3.208 1.844,3.406 0.313,0.198 10 false 2 3.292,3.438 3.604,3.635 0.313,0.198 10 false 1 4.865,4.135 5.177,4.333 0.313,0.198 10 false 1 3.271,3.917 3.583,4.115 0.313,0.198 10 false 2 4.865,4.583 5.177,4.781 0.313,0.198 10 false 2 1.698,6.906 2.406,7.104 0.708,0.198 10 false G43 1.688,7.073 3.177,7.271 1.49,0.198 10 false Telltale Light Assembly 0.719,7.417 2.865,7.615 2.146,0.198 10 false : CAN Communication Line 5.615,6.865 6.323,7.063 0.708,0.198 10 false G16 5.615,7.021 6.875,7.375 1.26,0.354 10 false Combination Meter Assembly 5.792,2.865 6.5,3.063 0.708,0.198 10 false RLSB 5.792,3.542 6.5,3.74 0.708,0.198 10 false RCSB 5.792,4.24 6.5,4.438 0.708,0.198 10 false RRSB 5.771,5.438 6.479,5.635 0.708,0.198 10 false RLMT 5.781,5.938 6.49,6.135 0.708,0.198 10 false RCMT 5.771,6.448 6.479,6.646 0.708,0.198 10 false RRMT 5.604,5.365 5.917,5.563 0.313,0.198 10 false 1 5.604,5.833 5.917,6.031 0.313,0.198 10 false 2 5.604,6.333 5.917,6.531 0.313,0.198 10 false 3 2.844,5.323 3.156,5.521 0.313,0.198 10 false 22 2.844,5.844 3.156,6.042 0.313,0.198 10 false 23 2.844,6.333 3.156,6.531 0.313,0.198 10 false 24 5.542,2.771 5.854,2.969 0.313,0.198 10 false 24 5.542,3.438 5.854,3.635 0.313,0.198 10 false 25 5.542,4.125 5.854,4.323 0.313,0.198 10 false 26 2.448,5.469 2.896,5.667 0.448,0.198 10 false RLID 2.438,5.979 2.885,6.177 0.448,0.198 10 false RCID 2.438,6.469 2.885,6.667 0.448,0.198 10 false RRID

CAUTION / NOTICE / HINT

NOTICE:
·

The seat belt warning system uses a CAN communication system. Inspect the communication function by following How to Proceed with troubleshooting.


·

When replacing the main body ECU (multiplex network body ECU), make sure to replace it with a new one.



PROCEDURE

1.READ VALUE USING GTS (RL DOOR COURTESY SW, RR DOOR COURTESY SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Door Courtesy SW Rear door LH courtesy light switch signal ON/OFF ON: Rear door LH open
OFF: Rear door LH closed
-
RL Door Courtesy SW Rear door RH courtesy light switch signal ON/OFF ON: Rear door RH open
OFF: Rear door RH closed
-
Body Electrical > Main Body > Data List
Tester Display
RR Door Courtesy SW
RL Door Courtesy SW
50003 123 24,25

Result:
Result Proceed to
ON or OFF is displayed on the GTS screen according to the rear door courtesy light switch condition A
ON or OFF is not displayed normally on the GTS screen according to the rear door courtesy light switch condition B



A

2.READ VALUE USING GTS (2ND-ROW SEATBELT BUCKLE [R], 2ND-ROW SEATBELT BUCKLE [L], 2ND-ROW SEATBELT BUCKLE [C])

B

2.READ VALUE USING GTS (2ND-ROW SEATBELT BUCKLE [R], 2ND-ROW SEATBELT BUCKLE [L], 2ND-ROW SEATBELT BUCKLE [C])
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
2nd-Row Seatbelt Buckle (R) Rear seat belt buckle RH signal ON/OFF ON: Rear seat belt RH fastened
OFF: Rear seat belt RH unfastened
-
2nd-Row Seatbelt Buckle (L) Rear seat belt buckle LH signal ON/OFF ON: Rear seat belt LH fastened
OFF: Rear seat belt LH unfastened
-
2nd-Row Seatbelt Buckle (C) Rear seat center belt buckle signal ON/OFF ON: Rear seat center belt fastened
OFF: Rear seat center belt unfastened
-
Body Electrical > Combination Meter > Data List
Tester Display
2nd-Row Seatbelt Buckle (R)
2nd-Row Seatbelt Buckle (L)
2nd-Row Seatbelt Buckle (C)
50003 122 74,75,76

Result:
Result Proceed to
ON or OFF is displayed on the GTS screen according to the rear seat belt condition A
ON or OFF is not displayed normally on the GTS screen according to the rear seat belt condition B



A

3.PERFORM ACTIVE TEST USING GTS (REAR SEAT BELT)

B

8.INSPECT REAR SEAT INNER BELT ASSEMBLY
3.PERFORM ACTIVE TEST USING GTS (REAR SEAT BELT)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Rear Seat Belt Rear seat belt warning light ON/OFF Confirm that the vehicle is stopped and the engine is idling.
Body Electrical > Combination Meter > Active Test
Tester Display
Rear Seat Belt
50004 122 100
OK:

The rear seat belt warning light on the combination meter assembly operates normally.



Result:
Proceed to
OK
NG



OK

4.REPLACE COMBINATION METER ASSEMBLY

NG

6.INSPECT TELLTALE LIGHT ASSEMBLY
4.REPLACE COMBINATION METER ASSEMBLY
a.

Replace the combination meter assembly with a new one.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CHECK REAR SEAT BELT WARNING LIGHT
5.CHECK REAR SEAT BELT WARNING LIGHT
a.

Check the operation of the rear seat belt warning light.

Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING LIGHT>INSPECTION


Result:
Proceed to
The rear seat belt warning light operates normally.
The rear seat belt warning light operates abnormally.



The rear seat belt warning light operates normally.

The rear seat belt warning light operates abnormally.

END (COMBINATION METER ASSEMBLY WAS DEFECTIVE)

6.INSPECT TELLTALE LIGHT ASSEMBLY
a.

Remove the telltale light assembly.

Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING LIGHT>REMOVAL


b.

Inspect the telltale light assembly.

Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING LIGHT>INSPECTION


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (TELLTALE LIGHT ASSEMBLY - COMBINATION METER ASSEMBLY AND BODY GROUND)

NG

REPLACE TELLTALE LIGHT ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (TELLTALE LIGHT ASSEMBLY - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the G43 telltale light assembly connector.


b.

Disconnect the G16 combination meter assembly meter connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G43-22 (RLID) - G16-1 (RLMT) Always Below 1 Ω
G43-23 (RCID) - G16-2 (RCMT)
G43-24 (RRID) - G16-3 (RRMT)
G43-22 (RLID) - Body ground Always 10 kΩ or higher
G43-23 (RCID) - Body ground
G43-24 (RRID) - Body ground



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT REAR SEAT INNER BELT ASSEMBLY
a.

for LH, RH:

Remove the rear seat inner belt assembly.

Click hereVehicle Interior>SEAT BELT>REAR SEAT INNER BELT ASSEMBLY>REMOVAL


b.

for Center:

Remove the rear center lap type seat belt assembly RH.

Click hereVehicle Interior>SEAT BELT>REAR CENTER SEAT OUTER BELT ASSEMBLY>REMOVAL


c.

for LH, RH:

Inspect the rear seat inner belt assembly.

Click hereVehicle Interior>SEAT BELT>REAR SEAT INNER BELT ASSEMBLY>INSPECTION


d.

for Center:

Inspect the rear center lap type seat belt assembly RH.

Click hereVehicle Interior>SEAT BELT>REAR CENTER SEAT OUTER BELT ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG (for LH)
NG (for Center)
NG (for RH)



OK

9.CHECK HARNESS AND CONNECTOR (REAR SEAT INNER BELT ASSEMBLY - COMBINATION METER ASSEMBLY AND BODY GROUND)

NG (for LH)

REPLACE REAR SEAT INNER BELT ASSEMBLY LH

NG (for Center)

REPLACE REAR CENTER LAP TYPE SEAT BELT ASSEMBLY RH

NG (for RH)

REPLACE REAR SEAT INNER BELT ASSEMBLY RH

9.CHECK HARNESS AND CONNECTOR (REAR SEAT INNER BELT ASSEMBLY - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the M12*1, M13*2 or M14*3 rear seat inner belt assembly connector.

*1: for RH

*2: for Center

*3: for LH



b.

Disconnect the G16 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LH:
Tester Connection Condition Specified Condition
M14-1 - G16-24 (RLSB) Always Below 1 Ω
M14-2 - Body ground
M14-1 - Body ground Always 10 kΩ or higher

for Center:
Tester Connection Condition Specified Condition
M13-1 - G16-25 (RCSB) Always Below 1 Ω
M13-2 - Body ground
M13-1 - Body ground Always 10 kΩ or higher

for RH:
Tester Connection Condition Specified Condition
M12-1 - G16-26 (RRSB) Always Below 1 Ω
M12-2 - Body ground
M12-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR