Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING UNIT › 2012.12–2013.11
RM3090E _58 Vehicle Interior _008789 HEATING / AIR CONDITIONING _0050143 AIR CONDITIONING UNIT A

HEATING / AIR CONDITIONING  AIR CONDITIONING UNIT  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

A bolt without a torque specification is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS



PROCEDURE

Hide 82210K 1.INSTALL AIR CONDITIONING HARNESS ASSEMBLY (for Automatic Air Conditioning System)

a.

Route the air conditioning harness assembly as shown in the illustration.

E260966


b.

Connect each connector.


c.

Engage each clamp to install the air conditioning harness assembly.


Hide 88539J 2.INSTALL DRAIN COOLER HOSE

a.
E265970C01
0.458,1.823 0.573,1.677 false 0.698,1.885 0.688,1.708 false 0.646,1.896 0.958,2.094 0.313,0.198 10 *a 0.385,1.833 0.698,2.031 0.313,0.198 10 *b
*a Hose Notch
*b Rib


Align the hose notch and rib as shown in the illustration and install the drain cooler hose.


Hide 88650N 3.INSTALL AIR CONDITIONING AMPLIFIER ASSEMBLY

Hide 55388B 4.INSTALL CONSOLE MOUNTING BRACKET RH

a.

Attach the 2 claws to install the console mounting bracket RH.


Hide 55389 5.INSTALL CONSOLE MOUNTING BRACKET LH

a.

Install the console mounting bracket LH with the screw.


Hide 88505 6.INSTALL AIR CONDITIONING DUCT SUB-ASSEMBLY (for Automatic Air Conditioning System)

a.

Engage the 2 claws to install the air conditioning duct sub-assembly.


Hide 8.TEMPORARILY INSTALL AIR CONDITIONER UNIT ASSEMBLY

a.

Temporarily install the air conditioner unit assembly with the bolt and nut.

NOTICE:

To prevent damage to the installation bracket for the air conditioner unit assembly, be sure to support the air conditioner unit assembly in place.



b.

Connect the drain cooler hose.


Hide 55330B 9.INSTALL INSTRUMENT PANEL REINFORCEMENT ASSEMBLY

a.

Install the instrument panel reinforcement assembly with the 6 bolts <A>.

E270981N01
1.135,0.875 1.458,1.083 0.323,0.208 10 <A> 2.99,0.417 3.313,0.625 0.323,0.208 10 <A> 4.719,0.177 5.042,0.385 0.323,0.208 10 <A> 5.49,0.177 5.813,0.385 0.323,0.208 10 <A> 6.635,3.385 6.958,3.594 0.323,0.208 10 <B> 5.927,4.938 6.25,5.146 0.323,0.208 10 <B> 4.042,4.885 4.365,5.094 0.323,0.208 10 <B>


b.

Temporarily install the 3 bolts <B>.


Hide 55307C 10.INSTALL NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

a.

Install the No. 2 instrument panel brace sub-assembly with the bolt, screw and nut.

HINT:

Do not fully tighten the screw.



b.

Install the front floor carpet assembly to the original position and install the clip.


Hide 55306A 11.INSTALL NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

a.

Install the No. 1 instrument panel brace sub-assembly with the bolt, screw and nut.

HINT:

Do not fully tighten the screw.



b.

Install the front floor carpet assembly to the original position and install the clip.


Hide 82141 12.INSTALL INSTRUMENT PANEL WIRE (for LHD)

a.

Attach each clamp.

E269765C01
6.781,1.24 7.156,1.438 0.375,0.198 10 <A> 4.958,0.229 5.333,0.427 0.375,0.198 10 <C> 1.99,0.167 2.365,0.365 0.375,0.198 10 <A> 2.135,5.844 2.51,6.042 0.375,0.198 10 <B> 5.917,1.24 6.292,1.438 0.375,0.198 10 <B> 5.896,3.177 6.125,3.375 0.229,0.198 10 *1 0.146,5.083 0.375,5.281 0.229,0.198 10 *2
*1 ECU Integration Box RH *2 Instrument Panel Junction Block Assembly



b.

Connect each connector.


c.

Connect the ECU integration box RH with the 2 nuts and bolt.

Torque:
for Nut : 5.5 N*m (56 kgf*cm, 49 in.*lbf)
for Bolt : 12 N*m (122 kgf*cm, 9 ft.*lbf)


d.

Connect the instrument panel junction block assembly with the 2 bolts.

Torque:
3.2 N*m (33 kgf*cm, 28 in.*lbf)


e.

Connect the instrument panel wire with the 2 bolts <A>.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


f.

Connect the ground wire with the 3 bolts.

Torque:
for Bolt <B> : 8.4 N*m (86 kgf*cm, 74 in.*lbf)
for Bolt <C> : 8.5 N*m (87 kgf*cm, 75 in.*lbf)


g.

w/ PTC Heater:

Connect the 2 or 3 connectors.


Hide 82141 13.INSTALL INSTRUMENT PANEL WIRE (for RHD)

a.

Attach each clamp.

E270982C01
0.333,6.49 0.51,6.25 true 0.927,6.354 1.083,6.219 true 5.823,4.906 6.135,5.063 0.313,0.156 10 false *1 0.167,6.49 0.479,6.646 0.313,0.156 10 false *2 6.26,1.396 6.604,1.594 0.344,0.198 10 false <A> 6.802,0.229 7.146,0.427 0.344,0.198 10 false <A> 5.073,2.135 5.417,2.333 0.344,0.198 10 false <B> 5.292,0.635 5.635,0.833 0.344,0.198 10 false <C> 1.094,2.552 1.438,2.75 0.344,0.198 10 false <A> 0.813,2.031 1.156,2.229 0.344,0.198 10 false <B> 1.104,6.083 1.323,6.302 0.219,0.219 10 true *3
*1 ECU Integration Box RH *2 Instrument Panel Junction Block Assembly
*3 Engeine Stop and Start ECU - -



b.

Connect each connector.


c.

Connect the ECU integration box RH with the 3 bolts.

Torque:
for Nut : 5.5 N*m (56 kgf*cm, 49 in.*lbf)
for Bolt : 12 N*m (122 kgf*cm, 9 ft.*lbf)


d.

Connect the instrument panel junction block assembly with the 2 nuts and bolt.

Torque:
for Nut : 8.4 N*m (86 kgf*cm, 74 in.*lbf)
for Bolt : 8.4 N*m (86 kgf*cm, 74 in.*lbf)


e.

Install the engine stop and start ECU with the bolt and nut.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


f.

Connect the instrument panel wire with the 3 bolts <A>.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


g.

Connect the ground wire with the 3 bolts.

Torque:
for Bolt <B> : 8.4 N*m (86 kgf*cm, 74 in.*lbf)
for Bolt <C> : 8.5 N*m (87 kgf*cm, 75 in.*lbf)


h.

w/ PTC Heater:

Connect the 2 or 3 connectors.


Hide 14.INSTALL AIR CONDITIONER UNIT ASSEMBLY

a.

for LHD:

Tighten the 4 bolts, 2 screws and nut.

E269762N01
3.135,1.24 3.292,1.438 0.156,0.198 10 1 5.531,1.198 5.688,1.396 0.156,0.198 10 2 0.792,1.26 0.948,1.458 0.156,0.198 10 3 1.833,5.76 2.031,5.948 0.198,0.188 10 4 3.76,6.104 3.917,6.302 0.156,0.198 10 5 4.979,6.281 5.135,6.479 0.156,0.198 10 6 6.052,6.25 6.208,6.448 0.156,0.198 10 7

Torque:
for Bolt : 9.8 N*m (100 kgf*cm, 7 ft.*lbf)

NOTICE:

Tighten the bolts, screws and nut in the order shown in the illustration to install the air conditioner unit assembly.



b.

for RHD:

Tighten the 4 bolts, 2 screws and nut.

E270983N01
6.323,1.208 6.479,1.406 0.156,0.198 10 1 1.667,1.25 1.823,1.448 0.156,0.198 10 2 4.052,1.208 4.208,1.406 0.156,0.198 10 3 6.229,6.208 6.385,6.406 0.156,0.198 10 4 4.135,5.76 4.292,5.958 0.156,0.198 10 5 1.188,6.063 1.344,6.26 0.156,0.198 10 6 1.052,6.406 1.208,6.604 0.156,0.198 10 7

Torque:
for Bolt : 9.8 N*m (100 kgf*cm, 7 ft.*lbf)

NOTICE:

Tighten the bolts, screws and nut in the order shown in the illustration to install the air conditioner unit assembly.



Hide 87201F 15.INSTALL NO. 3 AIR DUCT SUB-ASSEMBLY

a.

Attach the 2 claws to install the No. 3 air duct sub-assembly.

NOTICE:

If any of the claws of the No. 3 air duct sub-assembly are cracked or deformed, make sure to replace the air duct with a new one. Failure to do so may cause the No. 3 air duct sub-assembly to fall off or noise to occur.



Hide 87201B 16.INSTALL NO. 2 AIR DUCT SUB-ASSEMBLY

a.

Attach the 2 claws to install the No. 2 air duct sub-assembly.

NOTICE:

If any of the claws of the No. 2 air duct sub-assembly are cracked or deformed, make sure to replace the air duct with a new one. Failure to do so may cause the No. 2 air duct sub-assembly to fall off or noise to occur.



Hide 55950G 17.INSTALL DEFROSTER NOZZLE ASSEMBLY

a.

Attach the 3 hooks to install the defroster nozzle assembly.


b.

Connect the automatic light control sensor (solar sensor) connector and attach the 2 harness clamps.


Hide 87220 18.INSTALL AIR DUCT ASSEMBLY

a.

Install the air duct assembly with the 2 nuts.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 87212 19.INSTALL REAR NO. 1 AIR DUCT

a.

Attach the 8 claws to install the rear No. 1 air duct.


Hide 20.INSTALL STEERING COLUMN ASSEMBLY

Hide 55303B 21.INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY

Hide 87245A 22.CONNECT HEATER WATER HOSE

a.
E269763C01
1.74,2.656 2.344,2.417 true 1.75,3.615 2.417,3.323 false 2.198,0.74 2.51,0.896 0.313,0.156 10 *a 2.406,2.302 2.719,2.458 0.313,0.156 10 *b 2.479,3.229 2.792,3.385 0.313,0.156 10 *c 1.646,2.198 1.958,2.354 0.313,0.156 10 *d 1.635,4.51 1.948,4.667 0.313,0.156 10 *d
*a View A
*b Heater Water Outlet Hose Paint Mark
*c Heater Water Inlet Hose Paint Mark
*d Clip installation angle (270°)


Connect the heater water outlet hose A and heater water inlet hose A with the paint mark facing up and attach the clip within the area shown in the illustration.

Paint Mark Color:
Engine Transmission Hose Color
2AR All Outlet Purple
Inlet Purple
3ZR Manual Transmission Outlet Pink
Inlet Pink
CVT Outlet Pink
Inlet Orange
1AD, 2AD w/o Fuel Heater Outlet Blue
Inlet Blue
w/ Fuel Heater Outlet Grean
Inlet Grean


NOTICE:

Do not apply excessive force to the heater water outlet hose A and heater water inlet hose A.



Hide 88707 23.CONNECT AIR CONDITIONING TUBE

a.
E269764

Remove the vinyl tape from the suction tube sub-assembly and liquid tube sub-assembly.


b.

Sufficiently apply compressor oil to 2 new O-rings and fitting surface of the suction tube sub-assembly and liquid tube sub-assembly.

Compressor Oil:

ND-OIL 8 or equivalent



c.

Install the 2 O-rings to the suction tube sub-assembly liquid tube sub-assembly.


d.

Connect the liquid tube sub-assembly and suction tube sub-assembly.


e.

Rotate the hook connector in the direction indicated by the arrow in the illustration and install the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 24.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 26.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT

Hide 30.INITIALIZATION SERVO MOTOR